TL;DR
Researchers have developed a simple method to improve the efficiency of perovskite solar cells by controlling the "hot-casting" temperature of the nickel oxide (NiOx) hole transport layer. By precisely adjusting this temperature, they can tune the concentration of defects within the NiOx, leading to better energy level alignment and improved charge transport, ultimately boosting the solar cell's power conversion efficiency by over 36%.
What Problem Does This Paper Address?
Perovskite solar cells (PSCs) are a promising next-generation photovoltaic technology due to their high efficiency and low manufacturing costs. A critical component in PSCs is the hole transport layer (HTL), which facilitates the extraction of positive charges (holes) from the perovskite layer to the electrode. Nickel oxide (NiOx) is a popular choice for HTLs due to its stability and favorable electronic properties. However, the efficiency of NiOx-based PSCs can be limited by issues like energy losses at the interface between the perovskite and the HTL, and inefficient charge transport. Existing methods for fabricating NiOx films, such as spin coating, often require expensive vacuum techniques or can lead to inconsistent results. This paper aims to address the challenge of optimizing NiOx for efficient hole transport and improved PSC performance by exploring a facile, solution-based method to control its electronic structure.
Methods
The researchers employed a hot-casting spin-coating technique to deposit NiOx thin films. This method involves spinning a precursor solution onto a substrate while simultaneously heating the substrate. The key innovation here is the systematic variation of the deposition temperature (from room temperature to 150°C) to intentionally modulate the concentration of nickel vacancies (Ni²⁺ defects) within the NiOx film.
To characterize the NiOx films and their impact on solar cell performance, a suite of techniques was utilized:
- X-ray Photoelectron Spectroscopy (XPS): Used to analyze the chemical states of nickel (Ni²⁺ and Ni³⁺) and determine the ratio of Ni³⁺/Ni²⁺, which is directly related to the concentration of nickel vacancies.
- Ultraviolet Photoelectron Spectroscopy (UPS): Employed to measure the work function (WF) and valence band maximum (VBM) of the NiOx films, crucial for understanding energy level alignment.
- Linear Sweep Voltammetry (LSV) and Dark-Current-Voltage (J-V) measurements: Used to probe the electrical conductivity of the NiOx films.
- Dark-Charge Extraction by Linearly-Increasing Voltage (dark-CELIV): Utilized to assess relative permittivity and infer conductivity.
- X-ray Diffraction (XRD): Used to confirm the crystalline structure of the perovskite layer deposited on the NiOx films.
- Photoluminescence (PL) and Time-Resolved Photoluminescence (TRPL): Investigated charge carrier dynamics and recombination within the perovskite layer when paired with different NiOx films.
- Device Fabrication and Characterization: Full perovskite solar cell devices were fabricated with varying NiOx HTLs. Their performance was evaluated using current density-voltage (J-V) curves, Incident Photon-to-Electron Conversion Efficiency (IPCE) spectra, and stability tests.
- Density Functional Theory (DFT) Calculations: Performed to provide theoretical insights into how nickel vacancies affect the electronic structure and conductivity of NiOx.
Datasets
Not discussed in the paper. The study focuses on experimental fabrication and characterization of solar cells using materials readily available from commercial suppliers.
Key Insights and Ideas
- Defect Engineering is Key: The study highlights that controlling point defects, specifically nickel vacancies, in NiOx is a powerful strategy to tune its electronic properties.
- Hot-Casting Temperature Matters: The deposition temperature during the hot-casting process directly influences the Ni³⁺/Ni²⁺ ratio, and thus the defect concentration. An optimal temperature (120°C in this case) was found to yield the best results.
- Lower HOMO Level, Better Performance: Modulating NiOx defects leads to a lower-lying Highest Occupied Molecular Orbital (HOMO) level. This improved energy level alignment with the perovskite layer reduces energy losses and enhances hole injection efficiency.
- Conductivity and Mobility Boost: Increased nickel vacancies not only improve energy level alignment but also significantly enhance the electrical conductivity and hole mobility of the NiOx film. This facilitates balanced charge transport and prevents charge accumulation at the perovskite/HTL interface.
- DFT Supports Experiment: Theoretical DFT calculations corroborate the experimental findings, demonstrating that nickel vacancies alter the electronic structure and promote metallic properties in NiOx.
Key Results
- Optimal NiOx Deposition Temperature: A deposition temperature of 120°C for the NiOx film resulted in the highest power conversion efficiency (PCE).
- Efficiency Improvement: The champion device fabricated with NiOx deposited at 120°C achieved a PCE of 17.03%, representing a 36.24% improvement compared to the device with NiOx deposited at room temperature (25°C), which had a PCE of 12.5%.
- Improved J-V Parameters: The optimized NiOx film led to significant enhancements in short-circuit current density (Jsc) and fill factor (FF), along with a slight increase in open-circuit voltage (Voc).
- Enhanced Charge Transport: PL and TRPL measurements showed a stronger quenching effect and reduced carrier lifetimes for perovskite films on NiOx-120, indicating improved hole extraction. SCLC measurements revealed a significantly higher hole mobility (1.073 × 10⁻⁴ cm² V⁻¹ s⁻¹) for NiOx-120 compared to other samples.
- Reduced Recombination: EIS and TPV measurements indicated a higher recombination resistance and longer recombination time for devices using NiOx-120, suggesting suppressed charge recombination.
- Negligible Hysteresis: The optimized device exhibited a very low hysteresis index, indicating stable performance.
- Good Stability: The NiOx-120 based devices showed satisfactory long-term stability under both environmental and thermal stress conditions.
Limitations and Future Work
- Thickness of NiOx: The paper notes that the NiOx films are very thin, making them difficult to detect with XRD. While this is typical for HTLs, further investigation into thicker NiOx layers or alternative deposition methods might be explored.
- Scalability of Hot-Casting: While hot-casting is presented as a facile method, further studies would be needed to assess its scalability for large-area device fabrication.
- Broader Material Systems: The study focuses on NiOx as an HTL in a specific perovskite composition (MAPbI₃). Future work could explore the applicability of this defect modulation strategy to other perovskite compositions and device architectures.
- In-depth Defect Characterization: While XPS provides evidence for Ni³⁺/Ni²⁺ ratios, more advanced techniques could offer deeper insights into the precise nature and distribution of vacancies and their impact on electronic structure.
The authors suggest that this facile method of manipulating NiOx electronic structure through deposition temperature offers a promising avenue for further improving the performance of perovskite solar cells and other related optoelectronic devices.
Summary updated