Toward three-dimensional hybrid inorganic/organic optoelectronics based on GaN/oCVD-PEDOT structures

Linus Krieg, Florian Meierhofer, Sascha Gorny, Stefan Leis, Daniel Splith, Zhipeng Zhang, Holger von Wenckstern, Marius Grundmann, Xiaoxue Wang, Jana Hartmann, Christoph Margenfeld, Irene Manglano Clavero, Adrian Avramescu, Tilman Schimpke, Dominik Scholz, Hans‐Jürgen Lugauer, Martin Straßburg, Jörgen Jungclaus, Steffen Bornemann, Hendrik Spende, A. Waag, Karen K. Gleason, T. VossNature Communications 2020 · DOI

TL;DR

This paper presents a novel method for creating 3D hybrid inorganic-organic optoelectronic devices by using oxidative chemical vapor deposition (oCVD) to grow conductive PEDOT polymer as a p-type contact on GaN microrods. This approach overcomes challenges in fabricating 3D GaN devices and demonstrates improved light emission properties in hybrid microrod LEDs compared to their purely inorganic counterparts.

What Problem Does This Paper Address?

The development of three-dimensional (3D) semiconductor nano- and micro-devices, particularly light-emitting diodes (LEDs), holds significant promise for cost reduction and enhanced performance. GaN-based micro- and nanostructures are attractive due to their potential for large emission areas and defect-free surfaces. However, a major hurdle in realizing 3D GaN devices is the complex fabrication of electrical contacts and optimizing light outcoupling, especially for structures with high aspect ratios where traditional planar fabrication techniques fail. Hybrid integration with organic functional films offers a flexible solution, but achieving conformal, high-quality coatings on 3D structures remains a challenge. Specifically, the paper addresses the need for a scalable and reliable method to create p-type contacts on 3D GaN structures, which is crucial for efficient optoelectronic device operation.

Methods

The core of this research lies in the application of Oxidative Chemical Vapor Deposition (oCVD) for growing conductive polymer thin films. Unlike conventional spin-coating methods, oCVD allows for the in-situ polymerization and doping of monomers from the gas phase, resulting in highly conformal, pinhole-free coatings on complex 3D substrates. The authors specifically used oCVD to deposit poly(3,4-ethylenedioxythiophene) (PEDOT), a hole-conductive polymer, onto GaN microrods.

Key techniques employed include:

  • Oxidative Chemical Vapor Deposition (oCVD): Used to deposit conformal PEDOT layers on both planar GaN substrates and 3D GaN microrod structures. This method is highlighted for its ability to maintain the morphology of the underlying 3D structures.
  • Scanning Electron Microscopy (SEM): Used for imaging the morphology of the uncoated and coated microrods, as well as the planar devices, to assess the quality and conformality of the PEDOT layers.
  • Raman Spectroscopy: Employed to confirm the presence of PEDOT on the coated microrods and to analyze the characteristic peaks of both GaN and PEDOT.
  • Current-Voltage (I-V) Measurements: Performed on planar n-GaN/PEDOT heterojunctions to characterize their electrical properties, including rectification ratios, temporal and thermal stability, and to extract parameters like barrier heights and ideality factors using a Schottky model.
  • Electroluminescence (EL) and Cathodoluminescence (CL) Spectroscopy: Used to analyze the light emission properties of both planar and 3D hybrid LEDs, comparing them to purely inorganic GaN-based devices. CL was used for mapping emission along the height of microrods.
  • Capacitance-Voltage (C-V) Measurements: Used to determine donor densities in GaN layers and to cross-validate barrier height measurements.

The paper emphasizes that oCVD is a superior method for achieving homogeneous coatings on 3D structures compared to spin-coating, which often leads to non-uniform layers and bridging.

Datasets

Not discussed in the paper. The study focuses on fabricating and characterizing novel device structures rather than training on or evaluating against existing datasets.

Key Insights and Ideas

  • oCVD as a Game-Changer for 3D Hybrid Devices: The research strongly advocates for oCVD as the go-to technique for depositing conductive polymers onto complex 3D nanostructures. Its ability to create conformal, pinhole-free layers without damaging the underlying morphology is a significant advantage over traditional methods.
  • PSS-Free PEDOT for High-Quality Interfaces: By using oCVD to deposit pure PEDOT (without the insulating PSS additive commonly used in solution-processed PEDOT), the authors achieve superior electrical properties and a lower defect density at the GaN/PEDOT interface. This is crucial for efficient charge transport and device performance.
  • PEDOT as a Viable p-Type Contact for GaN LEDs: The study demonstrates that oCVD PEDOT can effectively replace traditional p-GaN layers in GaN-based LEDs, offering a more flexible and potentially lower-cost fabrication route.
  • Enhanced Light Emission in Hybrid 3D LEDs: The hybrid microrod LEDs fabricated using oCVD PEDOT exhibit improved optical properties, specifically a larger light-emitting area due to superior lateral current spreading by the PEDOT layer compared to p-GaN. This is a critical finding for realizing efficient 3D optoelectronic devices.
  • Excellent Stability of Hybrid Interfaces: The n-GaN/PEDOT heterojunctions show remarkable temporal and thermal stability, with high rectification ratios maintained over extended periods and after thermal cycling. This is a key requirement for practical device applications.

Key Results

  • High Rectification Ratios: Planar n-GaN/PEDOT heterojunctions achieved rectification ratios of up to $10^7$ at ±2 V, demonstrating excellent diode characteristics.
  • Excellent Temporal and Thermal Stability: The electrical properties of the hybrid junctions remained stable for over 2 years under ambient conditions and after heating to 423 K.
  • Low Ideality Factors: Ideality factors for the hybrid interface were found to be in the range of 1.30-2.01, which are among the lowest reported for PEDOT/GaN structures, indicating a high-quality interface with low defect density.
  • Mean Barrier Height: The mean barrier height at zero bias for the n-GaN/PEDOT interface was determined to be (1.42 ± 0.01) eV, consistent with the difference between PEDOT work function and GaN electron affinity.
  • Improved Light Emission in Hybrid LEDs: Hybrid planar LEDs showed homogeneous light emission over the entire active area, attributed to the superior current spreading of PEDOT compared to p-GaN.
  • Demonstration of 3D Hybrid Microrod LEDs: The paper successfully fabricated and characterized 3D hybrid microrod LEDs, showcasing their electroluminescence and comparing their performance to purely inorganic microrod LEDs. The hybrid structures exhibited enhanced current spreading, leading to a larger light-emitting area.

Limitations and Future Work

  • Limitations:
    • While the study demonstrates excellent stability, the authors note that the Au encapsulation on top of the PEDOT layer likely prevents degradation effects observed in other studies. The long-term stability without such encapsulation might be a concern.
  • The breakdown voltage of the hybrid structure was found to be around -7.8 V, with a hard irreversible breakdown occurring at -10.8 V. Further investigation into the breakdown mechanisms and potential improvements might be necessary for high-power applications.
  • The defect luminescence around 560 nm was observed to be more pronounced in conventional LEDs compared to hybrid LEDs, suggesting that while the hybrid structure improves light emission, further optimization might be needed to completely suppress defect-related emission.
  • Future Work:
    • The authors suggest that higher crystallinity of PEDOT layers, achievable with higher substrate temperatures or liquid oxidants during deposition, could further improve electrical characteristics.
  • The research opens avenues for fabricating more complex 3D microstructures for optoelectronics by leveraging the capabilities of oCVD PEDOT.
  • Further exploration of the band alignment and interface properties could lead to optimized device designs.
  • Investigating the impact of PEDOT's properties (e.g., conductivity, work function) on device performance in more detail would be beneficial.

Summary updated

Abstract

The combination of inorganic semiconductors with organic thin films promises new strategies for the realization of complex hybrid optoelectronic devices. Oxidative chemical vapor deposition (oCVD) of conductive polymers offers a flexible and scalable path towards high-quality three-dimensional inorganic/organic optoelectronic structures. Here, hole-conductive poly(3,4-ethylenedioxythiophene) (PEDOT) grown by oxidative chemical vapor deposition is used to fabricate transparent and conformal wrap-around p-type contacts on three-dimensional microLEDs with large aspect ratios, a yet unsolved challenge in three-dimensional gallium nitride technology. The electrical characteristics of two-dimensional reference structures confirm the quasi-metallic state of the polymer, show high rectification ratios, and exhibit excellent thermal and temporal stability. We analyze the electroluminescence from a three-dimensional hybrid microrod/polymer LED array and demonstrate its improved optical properties compared with a purely inorganic microrod LED. The findings highlight a way towards the fabrication of hybrid three-dimensional optoelectronics on the sub-micron scale.
BibTeX
@inproceedings{krieg2020toward,
  author = {Linus Krieg and Florian Meierhofer and Sascha Gorny and Stefan Leis and Daniel Splith and Zhipeng Zhang and Holger von Wenckstern and Marius Grundmann and Xiaoxue Wang and Jana Hartmann and Christoph Margenfeld and Irene Manglano Clavero and Adrian Avramescu and Tilman Schimpke and Dominik Scholz and Hans‐Jürgen Lugauer and Martin Straßburg and Jörgen Jungclaus and Steffen Bornemann and Hendrik Spende and A. Waag and Karen K. Gleason and T. Voss},
  title = {{Toward three-dimensional hybrid inorganic/organic optoelectronics based on GaN/oCVD-PEDOT structures}},
  booktitle = {Nature Communications},
  year = {2020},
  doi = {10.1038/s41467-020-18914-7},
}
Figure