Time-Resolved Temperature Mapping Leveraging the Strong Thermo-Optic Effect in Phase-Change Materials

Nicholas A. Nobile, John R. Erickson, Carlos Ríos, Yifei Zhang, Juejun Hu, Steven A. Vitale, Feng Xiong, Nathan YoungbloodACS 2023 · DOI

TL;DR

This paper introduces a novel, non-invasive technique to precisely map the temperature dynamics of phase-change materials (PCMs) like GST. By leveraging the strong thermo-optic effect in crystalline GST, researchers can now accurately characterize the heating and cooling rates of integrated photonic devices, crucial for their development and large-scale integration.

What Problem Does This Paper Address?

Phase-change materials (PCMs) are exciting for applications like tunable optical devices and non-volatile memory due to their ability to switch between crystalline and amorphous states. However, achieving this switch reliably, especially in large-scale integrated photonic circuits, is challenging. This is because PCMs often require high temperatures and extremely fast cooling rates (quenching) to revert to their amorphous state. While optical methods can achieve these conditions, electrically controlled heating and cooling in integrated devices are difficult to precisely characterize, especially in terms of their spatial and temporal thermal profiles. Existing methods for temperature measurement are often invasive, slow, or lack the necessary spatial resolution. This paper tackles the need for a non-invasive, high-resolution method to understand the thermal behavior of these devices after fabrication.

Methods

The core of this work is a thermo-optic (TO) reflectometry technique. Here's how it works:

  • Leveraging the Thermo-Optic Effect: Crystalline GST exhibits a strong thermo-optic effect, meaning its refractive index changes significantly with temperature. This change in refractive index alters how light reflects off the material.
  • Optical Probe: A continuous-wave (CW) diode laser acts as an optical probe. This probe is carefully chosen to have a low power density, ensuring it doesn't induce phase changes in the GST itself.
  • Reflectometry Setup: The reflected probe light is collected and analyzed. By measuring changes in the reflected light's intensity, researchers can infer changes in the GST's temperature.
  • Temperature Calibration: The relationship between the reflected light intensity and temperature is established using temperature-dependent ellipsometry. This allows for the extraction of thermo-optic coefficients for GST.
  • Spatial Mapping: The optical probe is rastered across the device, allowing for spatial mapping of the temperature response.
  • Temporal Resolution: The reflected signal is detected using a fast photodetector and oscilloscope, enabling sub-10 ns temporal resolution for capturing dynamic heating and cooling processes.
  • Device Fabrication: The technique is demonstrated on two common electro-thermal microheater designs: a platinum (Pt) heater and a doped-silicon heater, both integrated with a GST pixel.

This approach is non-invasive because it uses an optical probe and doesn't require electrical contacts to the PCM itself. It also offers diffraction-limited spatial resolution and high temporal resolution, overcoming limitations of previous methods.

Datasets

Not discussed in the paper.

Key Insights and Ideas

  • GST as a Built-in Thermometer: The strong thermo-optic effect in crystalline GST makes it an excellent intrinsic sensor for its own temperature. This bypasses the need for external temperature sensors that could interfere with device performance.
  • Direct Comparison of Heater Designs: The technique allows for a direct, quantitative comparison of the thermal performance of different microheater designs (Pt vs. doped-Si). This is crucial for optimizing device integration.
  • Validation of Simulations: The experimental results show excellent agreement with COMSOL Multiphysics simulations, validating both the simulation models and the experimental technique itself. This dual validation is powerful for device design and understanding.
  • Spatial Non-uniformity Matters: The spatial mapping reveals that while the center of the device might perform well, variations in heating and cooling rates near the edges can impact the reversibility of the phase change across the entire pixel. This highlights the importance of spatial characterization for reliable device operation.

Key Results

  • Heating Efficiency: The doped-silicon microheater demonstrates approximately 2x higher heating efficiency compared to the Pt microheater at steady state.
  • Dynamic Response: The silicon microheater exhibits significantly faster heating and cooling time constants (on the order of hundreds of nanoseconds) compared to the metal heater (on the order of microseconds), enabling much faster switching.
  • Spatial Uniformity: For the silicon microheater, the heating and cooling time constants were found to be largely spatially independent across the GST layer, indicating good uniformity.
  • Agreement with Simulations: Experimental measurements of temperature profiles and time constants showed excellent agreement with COMSOL simulations, with deviations primarily observed near the device edges.

Limitations and Future Work

  • Temperature Limit: The technique is limited to temperatures below the melting point of GST (~600 °C), as the thermo-optic effect deviates significantly during amorphization.
  • Probe Power: While the probe power is kept low to avoid phase changes, it still needs to be sufficient to generate a measurable reflection change.
  • Future Work: The authors suggest that this technique can be extended to other phase-change materials and used to optimize the design and integration of robust, reversible phase-change devices for large-scale applications. The ability to spatially map thermal dynamics is key to understanding and overcoming challenges in device performance and reliability.

Summary updated

Abstract

Optical phase-change materials are highly promising for emerging applications such as tunable metasurfaces, reconfigurable photonic circuits, and non-von Neumann computing. However, these materials typically require both high melting temperatures and fast quenching rates to reversibly switch between their crystalline and amorphous phases: a significant challenge for large-scale integration. In this work, we use temperature-dependent ellipsometry to study the thermo-optic effect in GST and use these results to demonstrate an experimental technique that leverages the thermo-optic effect in GST to enable both spatial and temporal thermal measurements of two common electro-thermal microheater designs currently used by the phase-change community. Our approach shows excellent agreement between experimental results and numerical simulations and provides a noninvasive method for rapid characterization of electrically programmable phase-change devices.
BibTeX
@inproceedings{nobile2023time,
  author = {Nicholas A. Nobile and John R. Erickson and Carlos Ríos and Yifei Zhang and Juejun Hu and Steven A. Vitale and Feng Xiong and Nathan Youngblood},
  title = {{Time-Resolved Temperature Mapping Leveraging the Strong Thermo-Optic Effect in Phase-Change Materials}},
  booktitle = {ACS},
  year = {2023},
  doi = {10.1021/acsphotonics.3c00620},
}
Figure