Abstract
In this study, a three-phase unified power quality conditioner (UPQC) topology based on a quadruple-active-bridge (QAB) is presented as an attractive solution to power quality issues. It is composed of three single-phase series converters, a three-phase shunt converter and a QAB converter located at the common DC-link. Since the bulky low frequency isolation transformers are replaced by the high frequency ones in QAB, it leads to higher power density, reduced weight and volume. The QAB converter could function as an energy router to provide multiple DC-link voltage access ports in the UPQC, which increase the flexibility of the UPQC. Finally, the MATLAB/Simulink simulation results and hardware-in-the-loop testing verify the correctness and effectiveness of the proposed topology and control method.
Introduction
As the modern power grid increasingly integrates renewable energy sources and electric vehicle charging infrastructure, power quality (PQ) issues such as voltage sags, swells, and harmonic distortions have become more prevalent. The Unified Power Quality Conditioner (UPQC) is often considered the ultimate solution for these issues, as it can simultaneously compensate for both voltage and current disturbances.
However, traditional UPQC designs rely heavily on bulky, low-frequency (LF) isolation transformers, which significantly increase the system's weight and footprint. While transformer-less designs exist, they often struggle with unbalanced loads or lack the modularity needed for multi-source integration. This paper introduces a novel UPQC topology that utilizes a high-frequency Quadruple-Active-Bridge (QAB) converter to replace traditional LF transformers, creating a compact "energy router" capable of handling complex grid conditions and renewable integration.
Proposed System Architecture
The core of the proposed system is the integration of a QAB converter at the common DC-link. The topology consists of three single-phase series converters designed to mitigate voltage-side issues and one three-phase shunt converter to address current-side distortions.
As shown in the system diagram, the QAB acts as a central hub with four ports: three ports connect to the individual series converters, while the fourth connects to the shunt converter. This multi-port structure allows for independent control of each phase, which is critical for managing unbalanced grid currents—a common limitation in simpler Dual-Active-Bridge (DAB) designs.
The QAB as an Energy Router
By shifting isolation to the high-frequency stage (operating at 100kHz), the physical size of the isolation components is drastically reduced. The QAB serves as an energy router, facilitating power flow between the different phases and the shunt converter. To analyze and control this flow, the authors developed equivalent circuit models to represent the interactions between the ports.
These models allow for precise Phase-Shift Modulation (PSM) to control the active power exchange between the DC links. Furthermore, the DC ports on the QAB provide a "plug-and-play" interface for renewable sources like PV arrays, allowing the UPQC to support the load's active power demand directly.
Advanced Control and Validation
To ensure stability under distorted grid conditions, the system employs several advanced control strategies:
- Adaptive Filtering: Replaces standard Phase-Locked Loops (PLL) for more accurate frequency tracking in noisy environments.
- Proportional Resonant (PR) Control: Specifically used in series converters to handle negative sequence and harmonic components.
- Moving Average Filter (MAF): Integrated into the shunt converter control to extract clean DC components from distorted signals.
The design was validated using MATLAB/Simulink and Hardware-in-the-Loop (HIL) testing with an OPAL-RT 4510 simulator. Key results include:
- Harmonic Mitigation: Reduced Total Harmonic Distortion (THD) from 8.56% to 2.06% under unbalanced conditions.
- Distortion Rejection: Maintained a clean load voltage (0.74% THD) even when the grid was heavily distorted (25% THD).
- Renewable Support: Successfully integrated a solar array, reducing grid active power demand from 8kW to 5kW.
Conclusion
The QAB-based UPQC topology offers a high-power-density solution for modern power quality challenges. By replacing bulky transformers with a high-frequency energy router, the system achieves superior flexibility and performance, particularly in unbalanced and renewable-heavy environments. Future work will focus on optimizing the Volt-Ampere (VA) capacity of components and expanding the energy router concept to include battery storage and fuel cell integration.
Summary updated