The Precipitation and Strengthening Behavior of Ni<sub>2</sub>(Mo,Cr) in HASTELLOY C-22HS Alloy, a Newly Developed High Molybdenum Ni-Base Superalloy

Xiaoyu Xie, Y. Zeng, Linlin Kou, Jianfeng Dong, L.m. Pike, D.l. Klarstrom2008 · DOI

Abstract

The precipitation and strengthening behavior has been studied in a newly developed high molybdenum Ni-base superalloy, HASTELLOY C-22HS alloy, for long time exposures of 1000hrs at 600, 625 and 650°C. The homogeneous precipitation of the long range ordered (LRO) phase Ni<sub>2</sub>(Mo,Cr) with an average size on the order of 10nm after a specially designed heat treatment contributes an excellent strengthening effect for this new superalloy. The grain boundary precipitation of high molybdenum containing phases such as M<sub>6</sub>C and μ phase has been studied via isothermal exposures in a wide temperature range of 600-1050°C.

Introduction

In high-performance engineering, nickel-base superalloys often face a difficult trade-off between mechanical strength and corrosion resistance. While many alloys rely on γ' or γ'' precipitates for strength, these chemistries are not always optimized for the most aggressive corrosive environments. HASTELLOY® C-22HS® was developed to bridge this gap, offering a rare combination of high strength and exceptional corrosion resistance.

To ensure the reliability of this alloy in industrial applications, researchers have characterized its microstructural stability. This involves understanding how strengthening precipitates evolve over time and identifying the conditions under which deleterious brittle phases, such as μ or P phases, might form at grain boundaries and cause intergranular embrittlement.

Strengthening via Long-Range Ordering

The exceptional strength of C-22HS is derived from the homogeneous precipitation of the Ni<sub>2</sub>(Mo,Cr) phase. Unlike the bulky precipitates found in many other superalloys, these are "Long-Range Ordered" (LRO) domains, typically only ~10nm in size. Their fine distribution allows the alloy to double its yield strength while maintaining high ductility.

Extracted figure from page 3 of The Precipitation and Strengthening Behavior of Ni&lt;sub&gt;2&lt;/sub&gt;(Mo,Cr) in HASTELLOY C-22HS Alloy, a Newly Developed High Molybdenum Ni-Base Superalloy

The stability of these LRO phases is highly temperature-dependent. At 600°C, the precipitates grow very slowly, maintaining their small size and strengthening effect. However, at 650°C, the precipitates coarsen significantly, reaching sizes of nearly 60nm over 1,000 hours of exposure.

Mechanical Performance

The impact of this LRO precipitation on mechanical properties is profound. Tensile testing reveals that the yield strength of age-hardened (MA+HT) C-22HS is approximately double that of the standard mill-annealed (MA) condition, both at room temperature and at elevated service temperatures like 595°C.

Comparative yield strengths of C-22 and C-22HS alloys showing the significant strengthening effect of age-hardening (MA+HT) compared to the standard mill-annealed (MA) condition.

Remarkably, despite this massive increase in strength, the material retains excellent ductility, with a reduction in area of 50-55%.

Microstructural Stability and Limitations

While the LRO phase provides internal grain strength, other phases can form at grain boundaries. Thermal exposure tests show that M<sub>6</sub>C carbides and μ phases are the primary grain boundary precipitates. At 650°C, the appearance of high-chromium M<sub>23</sub>C<sub>6</sub> carbides correlates with a sharp decline in impact toughness after 500 hours, as a continuous network forms along the boundaries.

Thermodynamic modeling and experimental T-T-T (Time-Temperature-Transformation) mapping indicate that above 800°C, these potentially embrittling phases can form in as little as 10 minutes. This suggests a clear upper temperature limit for long-term structural applications where toughness is critical.

Conclusion

HASTELLOY C-22HS represents a significant advancement in Ni-Cr-Mo alloy design. By leveraging the nanometer-scale Ni<sub>2</sub>(Mo,Cr) LRO phase, it achieves high strength without sacrificing the corrosion resistance or ductility typical of the C-22 family. While highly stable at temperatures up to 625°C, users must account for grain boundary precipitation and coarsening at higher temperatures to ensure long-term component integrity.

Summary updated

Abstract

The precipitation and strengthening behavior has been studied in a newly developed high molybdenum Ni-base superalloy, HASTELLOY C-22HS alloy, for long time exposures of 1000hrs at 600, 625 and 650C. The homogeneous precipitation of the long range ordered (LRO) phase Ni 2 (Mo,Cr) with an average size on the order of 10nm after a specially designed heat treatment contributes an excellent strengthening effect for this new superalloy. The grain boundary precipitation of high molybdenum containing phases such as M 6 C and phase has been studied via isothermal exposures in a wide temperature range of 600-1050C.
BibTeX
@misc{xie2008precipitation,
  author = {Xiaoyu Xie and Y. Zeng and Linlin Kou and Jianfeng Dong and L.M. Pike and D.L. Klarstrom},
  title = {{The Precipitation and Strengthening Behavior of Ni\&lt;sub\&gt;2\&lt;/sub\&gt;(Mo,Cr) in HASTELLOY C-22HS Alloy, a Newly Developed High Molybdenum Ni-Base Superalloy}},
  year = {2008},
  doi = {10.7449/2008/superalloys\_2008\_799\_805},
}
Figure