The Morphological Characteristics of the Particles of Woody Biomass Pulverized by Three Kinds of Mills

Chengbao Wu, Guosheng Gai, Yufen Yang, Lieshu Lin, Zhenghua Chen2016 · DOI

Abstract

This study investigates the pulverization of woody biomass with varying moisture levels using three distinct mechanical processes: universal (impact) milling, cutting milling, and cage (shear) milling. Using Scanning Electron Microscopy (SEM), the researchers analyzed the resulting particle morphologies and measured specific energy consumption. Findings reveal that cutting mills produce neat, flank-like particles and are the most energy-efficient. In contrast, cage mills produce smooth, rounded particles but consume significantly more energy, particularly as moisture content increases.

Introduction

As global energy demands shift toward renewables, woody biomass is projected to provide a substantial portion of the world's energy. However, converting raw wood into a form suitable for gasification or liquefaction requires pulverization—a process that increases surface area but is notoriously energy-intensive. This research compares how different mechanical forces (cutting, impact, and shear) influence both the physical shape of the particles and the energy required to produce them under different moisture conditions.

Experimental Methods

The study utilized woody chips (~5mm) sourced from the furniture industry. Three pulverization technologies were evaluated:

  1. Cutting Mill: Employs a rotary cutter and screen to shear wood into "flank" particles.
  2. Universal Mill (Impact): Uses high-speed hammers to break particles through repeated impact.
  3. Cage Mill (Shear): A high-power system utilizing intense friction and shear forces, often integrated with drying gases.
Process flow of the cage mill system, showing the separation of coarse and fine products through cyclone collection and bag filtration.

Samples were prepared at 0% and 20% moisture content. The resulting powders were analyzed via SEM to characterize surface morphology, and specific energy consumption was recorded in kWh/t.

Morphological Insights

The mechanical mechanism of each mill directly dictates the final particle shape:

  • Cutting Mill: Produces particles with neat, clean cross-sections due to the direct shearing of fibers.
  • Universal Mill: Results in rough, jagged surfaces caused by impact forces that bend and snap the wood fibers.
  • Cage Mill: Produces smooth, rounded particles. The prolonged residence time and intense friction within the cage mill actually deform the wood's internal structure.
Visual comparison of woody biomass particles. Image (a) shows the coarser, sheared shavings typical of cutting processes, while (b) displays the finer, more processed powder.

Energy Consumption and Moisture Effects

Moisture content is a critical factor in pulverization efficiency. As moisture increases, wood becomes more plastic, leading to "soft shear deformation" rather than brittle breakage. This transition significantly increases the energy required to achieve the same level of fineness.

Mill Type Energy at 0% Moisture (kWh/t) Energy at 20% Moisture (kWh/t)
Cutting Mill 47.00 90.76
Universal Mill 158.48 213.53
Cage Mill 120.99 255.47

The cutting mill proved to be the most efficient across both moisture levels. While the cage mill is relatively efficient for dry wood, its energy consumption more than doubles when moisture reaches 20%, making it the most energy-expensive option for damp biomass.

Conclusion

The choice of milling technology fundamentally alters the physical characteristics of woody biomass particles. While cutting mills offer the highest energy efficiency and produce neat, sheared particles, cage mills produce a unique, rounded morphology at a higher energy cost. These findings suggest that the selection of a mill should be guided by the specific requirements of downstream chemical processes and the moisture profile of the raw feedstock.

Summary updated

Abstract

The wood biomass with certain moisture content prepared by spraying artificially was pulverized by universal mill, cutting mill and the cage mill with the drying and transporting gas. The morphological characteristics of powder of the wood biomass with different moisture content were investigated by the scanning electrical microscope (SEM). The results indicated that particles of woody biomass pulverized by the cutting mill were flank and their cross sections of breakage were neatly, the breakage cross sections of those pulverized by the universal mill were rough, and the morphology of the particles of the woody product pulverized by cage mill was smooth, rounded, and their inner structure was deformed. When the moisture content was 0%, the specific energy consumption of the cutting mill, the cage mill and the universal mill was 47.00, 120.99 and 158.48 kWh/t, respectively; as the moisture content was 20%, the specific energy consumption of the cutting mill, the cage mill and the universal mill was 90.76, 255.47, 213.53 kWh/t, respectively.
BibTeX
@misc{wu2016morphological,
  author = {Chengbao Wu and Guosheng Gai and Yufen Yang and Lieshu Lin and Zhenghua Chen},
  title = {{The Morphological Characteristics of the Particles of Woody Biomass Pulverized by Three Kinds of Mills}},
  year = {2016},
  doi = {10.2991/icmcm-16.2016.62},
}
Figure