The Gibbs free energy of homogeneous nucleation: From atomistic nuclei to the planar limit

Bingqing Cheng, Gareth A. Tribello, Michele CeriottiThe Journal of Chemical Physics 2017 · DOI · arXiv

Abstract

In this paper we discuss how the information contained in atomistic simulations of homogeneous nucleation should be used when fitting the parameters in macroscopic nucleation models. We show how the number of solid and liquid atoms in such simulations can be determined unambiguously by using a Gibbs dividing surface and how the free energy as a function of the number of solid atoms in the nucleus can thus be extracted. We then show that the parameters (the chemical potential, the interfacial free energy, and a Tolman correction) of a model based on classical nucleation theory can be fitted using the information contained in these free-energy profiles but that the parameters in such models are highly correlated. This correlation is unfortunate as it ensures that small errors in the computed free energy surface can give rise to large errors in the extrapolated properties of the fitted model. To resolve this problem we thus propose a method for fitting macroscopic nucleation models that uses simulations of planar interfaces and simulations of three-dimensional nuclei in tandem. We show that when the chemical potentials and the interface energy are pinned to their planar-interface values, more precise estimates for the Tolman length are obtained. Extrapolating the free energy profile obtained from small simulation boxes to larger nuclei is thus more reliable.

Introduction

Nucleation—the initial stage of a phase transition, such as a liquid freezing into a solid—is a ubiquitous phenomenon in nature and technology. Despite its importance, accurately predicting the free energy barrier of nucleation remains a significant challenge in computational materials science. This paper addresses the limitations of standard fitting procedures in Classical Nucleation Theory (CNT) and proposes a more robust "tandem" approach to improve the reliability of atomistic simulations.

The Challenge of Classical Nucleation Theory

In molecular dynamics simulations, researchers typically observe the formation of nanoscopic nuclei. To predict the behavior of larger, macroscopic systems, they rely on CNT. This model describes the free energy $G(n)$ as a balance between the energy gain from forming the bulk solid (proportional to the chemical potential difference $\mu$) and the energy cost of creating an interface (proportional to the surface tension $\gamma$).

However, fitting these parameters to simulation data is notoriously difficult due to two main issues:

  1. Ambiguity in Cluster Definition: Defining which atoms belong to a small, fluctuating nucleus is non-trivial. Different definitions lead to different calculated energies.
  2. Parameter Correlation: The bulk and surface terms are highly correlated. Because both terms increase with the size of the nucleus, fitting algorithms struggle to distinguish their individual contributions.
Correlation between the chemical potential ($\mu_{sl}$) and surface tension ($\gamma_{\infty}^\Phi$) parameters, illustrating the "correlation trap" in standard CNT fitting.

As shown in Figure 2, small variations in the input data can lead to a wide range of correlated parameter values, making extrapolations to larger nuclei highly sensitive to error.

The Tandem Approach: Decoupling Parameters

To overcome these hurdles, the authors introduce a rigorous thermodynamic framework. First, they utilize a Gibbs dividing surface based on a global order parameter to define the number of atoms in a cluster ($n$) unambiguously. To map out the free energy surface efficiently, they employ well-tempered metadynamics.

The core innovation is the tandem approach. Instead of attempting to fit all CNT parameters solely to 3D cluster data, the researchers perform separate simulations of planar interfaces. These flat-slab simulations provide independent, high-precision values for the chemical potential ($\mu$) and the surface tension ($\gamma$). By "pinning" these values, the fitting of the 3D cluster data is reduced to a single variable: the Tolman correction ($\zeta$), which accounts for the curvature dependence of surface tension in small nuclei.

Key Results: Achieving Physical Consistency

The study, conducted on a Lennard-Jones system across various temperatures, demonstrates that this tandem approach significantly reduces statistical uncertainty. By anchoring the model with planar-interface data, the extrapolated properties of the 3D nuclei become far more reliable.

Temperature dependence of the chemical potential difference, surface tension, and Tolman length, comparing results from the tandem approach (red circles) with independent planar simulations (dashed lines/open circles).

As illustrated in Figure 3, the values for surface tension and chemical potential extracted from 3D clusters using the new method align almost perfectly with the independent planar results. This consistency confirms that the framework successfully bridges the gap between tiny atomistic nuclei and the macroscopic planar limit.

Limitations and Future Outlook

While the method proves highly effective for the isotropic Lennard-Jones system, real-world materials often exhibit anisotropic surface energies. Extending this framework to non-spherical, Wulff-shaped nuclei is a necessary next step. Additionally, the authors note that calculating the Tolman length from pressure tensors in planar simulations remains computationally demanding. Future research could also apply this methodology to heterogeneous nucleation, where the presence of surfaces adds further complexity to the modeling process.

Summary updated

Abstract

In this paper we discuss how the information contained in atomistic simulations of homogeneous nucleation should be used when fitting the parameters in macroscopic nucleation models. We show how the number of solid and liquid atoms in such simulations can be determined unambiguously by using a Gibbs dividing surface and how the free energy as a function of the number of solid atoms in the nucleus can thus be extracted. We then show that the parameters (the chemical potential, the interfacial free energy, and a Tolman correction) of a model based on classical nucleation theory can be fitted using the information contained in these free-energy profiles but that the parameters in such models are highly correlated. This correlation is unfortunate as it ensures that small errors in the computed free energy surface can give rise to large errors in the extrapolated properties of the fitted model. To resolve this problem we thus propose a method for fitting macroscopic nucleation models that uses simulations of planar interfaces and simulations of three-dimensional nuclei in tandem. We show that when the chemical potentials and the interface energy are pinned to their planar-interface values, more precise estimates for the Tolman length are obtained. Extrapolating the free energy profile obtained from small simulation boxes to larger nuclei is thus more reliable.
BibTeX
@article{cheng2017gibbs,
  author = {Bingqing Cheng and Gareth A. Tribello and Michele Ceriotti},
  title = {{The Gibbs free energy of homogeneous nucleation: From atomistic nuclei to the planar limit}},
  journal = {The Journal of Chemical Physics},
  year = {2017},
  doi = {10.1063/1.4997180},
}
Figure