Surface passivation using pyridinium iodide for highly efficient planar perovskite solar cells

Yitian Du, Jihuai Wu, Xinpeng Zhang, Qianjin Zhu, Mingjing Zhang, Xuping Liu, Yu Zou, Shibo Wang, Weihai SunJournal of Energy Chemistry 2020 · DOI

TL;DR

Researchers have developed a new surface passivation technique for perovskite solar cells using pyridinium iodide (PyI). This method significantly boosts cell efficiency and stability by effectively addressing surface defects, outperforming traditional passivation methods and leading to a champion efficiency of 21.42%.

What Problem Does This Paper Address?

Perovskite solar cells (PSCs) hold immense promise for next-generation photovoltaics due to their ease of fabrication and excellent optoelectronic properties. However, their widespread adoption is hindered by two major challenges: non-radiative recombination losses that limit their power conversion efficiency (PCE) below theoretical limits, and degradation issues accelerated by defects. These defects, often found at the surface and grain boundaries of perovskite films, act as "traps" for charge carriers, leading to recombination and reduced device performance. Furthermore, these defects can create pathways for moisture and oxygen ingress, accelerating material degradation. Therefore, effectively passivating these surface defects is crucial for achieving both high efficiency and long-term stability in PSCs.

Methods

The study introduces pyridinium iodide (PyI) as a novel surface passivation agent for perovskite solar cells. PyI is synthesized through a straightforward reaction between pyridine and hydroiodic acid. The researchers then fabricated planar perovskite solar cells using a standard architecture (FTO/TiO2/perovskite/HTL/Au).

The passivation process involved spin-coating a solution of PyI onto the perovskite layer, followed by a mild annealing step. For comparison, they also employed pyridine (Py), a Lewis base known to passivate under-coordinated Pb ions, under identical conditions.

To characterize the passivation effects, a suite of advanced techniques was utilized:

  • X-ray Photoelectron Spectroscopy (XPS): To investigate changes in the elemental composition and chemical states of the perovskite surface, specifically focusing on Pb 4f and C 1s core-level spectra.
  • Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM): To analyze the surface morphology and roughness of the perovskite films.
  • X-ray Diffraction (XRD): To confirm the crystal structure of the perovskite films after passivation.
  • UV-Vis Absorption and Tauc Plots: To assess changes in the optical properties and band gap of the perovskite films.
  • Steady-State Photoluminescence (PL) and Time-Resolved Photoluminescence (TRPL): To probe the charge carrier dynamics, specifically the suppression of non-radiative recombination and the increase in carrier lifetime.
  • Current Density-Voltage (J-V) Measurements: To evaluate the photovoltaic performance (PCE, open-circuit voltage (Voc), short-circuit current density (Jsc), and fill factor (FF)) under simulated sunlight. This included forward and reverse scans to assess hysteresis.
  • Dark J-V Measurements: To calculate the trap state density (ntrap) in the perovskite films.
  • Stability Tests: To assess the long-term performance of the devices under ambient conditions without encapsulation.

Datasets

Not discussed in the paper. The study focuses on experimental fabrication and characterization of perovskite solar cells.

Key Insights and Ideas

  • Dual-Action Passivation of PyI: Unlike pyridine (Py), which primarily interacts with positively charged defects (e.g., under-coordinated Pb), the zwitterionic nature of PyI allows it to interact with both positively charged defects and negatively charged iodine vacancies. This dual-action is key to its superior performance.
  • Effective Filling of Iodine Vacancies: XPS analysis revealed that PyI treatment significantly increased the Pb:I ratio, indicating the filling of iodine vacancies, which are known detrimental defects.
  • Smoother Surfaces, Better Interfaces: AFM measurements showed that PyI treatment resulted in the smoothest perovskite surfaces among the pristine, Py-treated, and PyI-treated samples. Smoother surfaces lead to better interfacial contact with the charge transport layers, reducing recombination.
  • Suppression of Non-Radiative Recombination: Both steady-state and time-resolved photoluminescence measurements demonstrated that PyI passivation effectively suppressed non-radiative recombination, leading to longer carrier lifetimes.
  • Reduced Trap State Density: Dark J-V measurements revealed a significant reduction in trap state density (ntrap) in PyI-treated devices, directly correlating with improved Voc and FF.
  • Enhanced Stability: PyI-treated devices exhibited superior stability under ambient conditions, retaining a higher percentage of their initial efficiency over 30 days compared to pristine and Py-treated devices. This is attributed to the elimination of surface defects that trigger degradation.

Key Results

  • Champion Efficiency: The PyI-treated planar perovskite solar cell achieved a champion power conversion efficiency (PCE) of 21.42%.
  • Improved Voc: The open-circuit voltage (Voc) was significantly enhanced to 1.187 V for PyI-treated devices, compared to 1.099 V for pristine devices.
  • Reduced Hysteresis: PyI treatment resulted in a very low hysteresis index (HI) of 0.012, indicating improved device stability and reliability.
  • Enhanced Stability: After 30 days of testing under ambient conditions, PyI-treated devices retained 81.4% of their initial efficiency, while pristine devices dropped to 49.4%.
  • Comparison with Py: PyI-treated devices outperformed Py-treated devices, achieving a higher PCE (21.42% vs. 20.37%) and a higher Voc (1.187 V vs. 1.144 V).

Limitations and Future Work

  • Concentration Optimization: While the paper optimized the concentration of PyI and Py, further fine-tuning might yield even better results.
  • Encapsulation: The stability tests were performed without encapsulation. Future work could explore the performance of encapsulated PyI-treated devices under more demanding conditions.
  • Mechanism Elucidation: While the study provides strong evidence for the dual-action passivation of PyI, further in-depth theoretical modeling could offer even deeper insights into the precise bonding and interaction mechanisms at the perovskite surface.
  • Scalability: The fabrication process is described at a lab scale. Investigating the scalability of this passivation method for large-area devices would be a valuable next step.

Summary updated

BibTeX
@article{du2020surface,
  author = {Yitian Du and Jihuai Wu and Xinpeng Zhang and Qianjin Zhu and Mingjing Zhang and Xuping Liu and Yu Zou and Shibo Wang and Weihai Sun},
  title = {{Surface passivation using pyridinium iodide for highly efficient planar perovskite solar cells}},
  journal = {Journal of Energy Chemistry},
  year = {2020},
  doi = {10.1016/j.jechem.2020.04.049},
}
Figure