Surface nanaostructure evolution of functionalized polypropylene fibers

Qufu Weı, Yingying Wang, Xueqian Wang, Fenglin Huang, Shengwei YangJournal of Applied Polymer Science 2007 · DOI

TL;DR

This paper investigates how treating polypropylene (PP) fibers with plasma and then coating them with copper changes their surface structure and properties. The researchers found that these treatments significantly alter the fiber's surface morphology, nanomechanical behavior, and electrical conductivity, opening doors for new functional materials.

What Problem Does This Paper Address?

Many everyday materials, from filters and bandages to protective clothing, rely on fibrous structures like those found in meltblown polypropylene (PP) nonwovens. The performance of these materials is heavily influenced by their surface characteristics, including how they interact with liquids (wetting), how easily they slide against other surfaces (friction), and their ability to conduct electricity. While PP fibers are versatile, their inherent properties might not be ideal for all applications. This paper addresses the challenge of modifying these PP fiber surfaces to enhance specific properties, aiming to expand their utility in various technological fields. The core question is how controlled surface treatments, specifically plasma activation followed by metal sputtering, can precisely engineer the nanostructure and, consequently, the functional performance of these fibers.

Methods

The researchers employed a multi-pronged approach to characterize the changes in the PP fibers:

  • Plasma Treatment: The PP nonwoven substrate was treated with oxygen plasma. This is a standard technique for surface activation, aiming to introduce reactive functional groups and alter surface energy.
  • Copper Sputter Coating: Following plasma treatment, the fibers were coated with a thin layer of copper (Cu) using a magnetron sputtering system. This technique allows for precise deposition of metal nanoclusters onto the fiber surface. The sputtering time was varied (10 and 20 minutes) to investigate the effect of coating thickness.
  • Scanning Probe Microscopy (SPM): This was the primary tool for visualizing the nanostructure.
  • Atomic Force Microscopy (AFM): Used to observe the topographical changes on the fiber surface at the nanoscale.
  • Lateral Force Microscopy (LFM): Employed to probe the nanomechanical properties, specifically changes in friction at the surface.
  • Environmental Scanning Electron Microscopy (ESEM): Used to examine the overall web structure of the nonwoven material and the morphology of the fibers at a lower magnification. ESEM also allowed for elemental analysis.
  • Energy Dispersive X-ray Analysis (EDX): Integrated with the ESEM, EDX was used to determine the elemental composition of the fiber surfaces, confirming the presence and distribution of copper after sputtering.
  • Electrical Resistivity Measurement: A standard four-probe array method was used to quantify the change in electrical conductivity of the treated fibers.

Datasets

Not discussed in the paper. The study uses a commercially available polypropylene meltblown nonwoven fabric as the substrate.

Key Insights and Ideas

  • Plasma as a Surface Primer: Oxygen plasma treatment doesn't just clean the surface; it actively creates "aggregate structures" on the PP fibers, roughening them and increasing surface friction. This suggests plasma prepares the surface for subsequent functionalization.
  • Copper Nanoclusters as Building Blocks: Sputter coating doesn't create a uniform film initially. Instead, it forms distinct copper nanoclusters on the fiber surface. The size and density of these clusters evolve with sputtering time.
  • Nanostructure Dictates Properties: The observed changes in surface morphology (roughening by plasma, nanocluster formation by Cu) directly correlate with changes in nanomechanical properties (increased friction) and electrical conductivity.
  • Tunable Conductivity: The electrical resistivity of the PP fibers can be dramatically reduced by copper sputtering, with longer sputtering times leading to lower resistivity. This is a direct consequence of the conductive copper layer.

Key Results

  • Morphology: AFM revealed that original PP fibers are relatively smooth. Plasma treatment roughened the surface, creating aggregate structures. Copper sputtering resulted in the formation of distinct nanoclusters (10-20 nm initially, growing larger and more compact with longer sputtering times).
  • Nanomechanical Properties: LFM showed that plasma treatment significantly increased surface friction. Further increases in friction were observed after copper sputtering, attributed to the presence of nanoclusters. Surface friction increased from less than 0.4 nN for untreated fibers to approximately 1.5 nN after 20 minutes of Cu sputtering.
  • Chemistry: EDX confirmed that plasma treatment introduced a small amount of oxygen, indicating the formation of functional groups. Copper was clearly detected after sputtering, with its signal increasing significantly with longer sputtering times.
  • Electrical Conductivity: Untreated and plasma-treated PP fibers exhibited very high surface resistivity (out of range, >10⁴ Ω cm). Copper sputtering dramatically reduced this resistivity, dropping to 0.95 Ω cm after 10 minutes and 0.27 Ω cm after 20 minutes.

Limitations and Future Work

  • Limited Sputtering Times: The study focused on 10 and 20 minutes of copper sputtering. Longer sputtering times or different sputtering pressures and powers could lead to further changes in nanostructure and properties.
  • Specific Plasma Gas: Only oxygen plasma was used. Other plasma gases or treatment parameters might yield different surface modifications.
  • Focus on PP: The findings are specific to polypropylene fibers. Extending this research to other polymer types could reveal broader applicability.
  • Future Work: The authors suggest that the ability to deposit well-controlled coatings on polymer fibers through techniques like sputtering can expand the applications of meltblown materials. This implies future research could explore specific applications where these enhanced properties (e.g., conductivity, altered friction) are beneficial, such as in antistatic textiles, sensors, or specialized filtration media.

Summary updated

Abstract

Abstract It is well‐known that fiber surface characteristics affect friction, wetting, conductivity, and other performance properties. This paper reports the evolution of the surface nanostructures of meltblown polypropylene (PP) fibers during the process of plasma treatment followed by copper (Cu) sputter coating. The effects of plasma treatment and Cu sputter coating on the surface morphology, chemistry, and properties of the fibers were characterized using scanning probe microscope (SPM), environmental scanning electron microscopy (ESEM), and electrical analysis. The atomic force mode (AFM) and lateral force mode (LFM) in the SPM were used to scan the fiber surface. AFM observations revealed the evolution of the surface morphology formed by surface treatment. The LFM images also indicated the change in surface nanomechanical behavior. A full energy dispersive X‐ray analysis (EDX) mounted on the ESEM was used to examine the change in the chemical compositions of the functional surfaces. The electrical properties of the functionalized materials were analyzed using electrical resistance test. The Cu sputter coating significantly altered the surface conductivity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007
BibTeX
@article{we2007surface,
  author = {Qufu Weı and Yingying Wang and Xueqian Wang and Fenglin Huang and Shengwei Yang},
  title = {{Surface nanaostructure evolution of functionalized polypropylene fibers}},
  journal = {Journal of Applied Polymer Science},
  year = {2007},
  doi = {10.1002/app.25401},
}
Figure