SunLightBots: Turning sunlight into self-sustained, high-power motion in soft robots

Yoo Jin Lee, Melanie Torres Crespo, Zhongxiao Deng, Andrew Tejada-Vega, Rebecca Kramer-Bottiglio, Wenzhong Yan, Yimin LuoarXiv 2026 · arXiv

TL;DR

SunLightBots are a new class of subgram soft robots that achieve autonomous, high-power locomotion using nothing but unconcentrated sunlight. By pairing optimized liquid crystal elastomers (LCEs) with a "self-resetting snapping" (SRS) mechanism, these robots accumulate low-intensity solar energy and release it in rapid bursts, achieving a peak mass-specific power of 89 W/kg.

What Problem Does This Paper Address?

The "power mismatch" is a fundamental hurdle in soft robotics. Environmental energy sources like sunlight are abundant but have low power density. Conversely, effective robotic actions—like jumping, swimming, or rapid shape-shifting—require high mechanical power delivered in short durations.

For subgram-scale robots, this problem is even worse: they are too small to carry heavy batteries or complex electronic controllers. While previous light-powered robots existed, they typically required highly concentrated light (often >6 Suns) or produced only "one-shot" motions. The authors sought a way to achieve autonomous, cyclic, and high-power motion under standard, unconcentrated sunlight (~1 Sun).

Methods

The researchers developed a self-resetting snapping (SRS) mechanism that functions like a mechanical capacitor. It consists of three main components:

  1. Optimized LCE Actuator: A photoresponsive material that contracts when heated by light. The team systematically screened material formulations (varying monomers, crosslink densities, and chain extenders) to find a "sweet spot": an LCE that generates high stress (0.1 MPa) at a relatively low actuation temperature (~60 °C).
  2. Monostable Curved Beam: The LCE is bonded to a curved elastomer beam. As the LCE contracts, it slowly loads the beam with elastic energy until it reaches a "snap-through" instability point, releasing that stored energy almost instantaneously.
  3. Self-Shadowing Shutters: Integrated shutters act as a physical feedback loop. When the beam is up, the LCE is exposed to light. Once it snaps down, the shutters close, shading the LCE so it can cool down, relax, and "snap back" to its original state to start the cycle again.
Overview of the SunLightBots mechanism and locomotion types.

To boost photothermal efficiency, they embedded silver (Ag) and copper (Cu) microparticles into the LCE, optimizing the loading to maximize heating without compromising the material's mechanical strength.

Datasets

As an experimental materials science and mechanics paper, this work does not use traditional computational datasets. Instead, the "data" consists of:

  • Thermomechanical Characterization: Extensive stress-strain-temperature profiles for dozens of LCE formulations (see Figure 2).
  • Ball-Launch Experiments: A custom setup used to quantify the energy released during snap-through by measuring the height a steel ball reaches when launched by the actuator.
  • Locomotion Benchmarks: Comparative data against previously reported light-driven swimmers and jumpers.

Key Insights and Ideas

  • Embodied Control: The robot doesn't need a "brain" or sensors to decide when to move. The control is "embodied" in the physical interaction between the light, the material's thermal response, and the structural geometry of the shutters.
  • The Power of Instability: Usually, engineers try to avoid mechanical instabilities like buckling or snapping. Here, the authors embrace "snap-through" as a vital tool for power amplification, concentrating slowly harvested energy into a high-intensity event.
  • Material-Mechanics Co-design: A high-performance LCE isn't enough on its own. The energy barrier of the passive elastomer beam must be perfectly matched to the stress the LCE can generate at 1 Sun. If the beam is too stiff, it never snaps; if it's too soft, it releases very little energy.
Optimization of LCE thermomechanical properties through various chemical strategies.

Key Results

  • High Power at Low Input: The system operates at ~1 Sun (100 mW/cm²) and achieves a peak mass-specific mechanical power of 89 W/kg, outperforming most previously reported photothermal actuators.
  • Versatile Locomotion:
    • Swimmer: Advances more than 3 body lengths per cycle under 1.5 Suns, making it one of the fastest light-powered swimmers to date.
  • Crawler: Achieves directional motion on solid surfaces by using asymmetric shutters and tilted legs.
  • Jumper: Performs repeated impulsive jumps (over 20 consecutive cycles) at 1.9 Suns, a significant improvement over previous designs requiring 6 Suns.
The sunlight-powered swimmer mechanism and performance.

Limitations and Future Work

  • Cycle Rate: While the peak power is high, the average power is limited by the time it takes for the LCE to thermally load and cool down. Future work could focus on thinner structures or active cooling to speed up the cycle.
  • Spectral Range: The current photothermal agents are efficient but could be further optimized for broader solar spectrum absorption.
  • Navigation: The robots currently move in a fixed direction relative to the light. Integrating phototactic mechanisms (moving toward or away from light) would be a major step toward true robotic autonomy.
  • Durability: Real-world deployment will require testing these materials against long-term UV degradation and varying environmental temperatures.

Summary updated

Abstract

Soft robots built from active materials can directly convert environmental stimuli into motion, offering a route to energy autonomy and embodied control. However, environmental energy is generally harvested at low power, whereas rapid, mechanically demanding actions require high mechanical output power. Reconciling this mismatch while sustaining self-regulated cyclic actuation is challenging, particularly at the subgram scale, where limited payload capacity constrains the integration of conventional power and control hardware. Here, we present SunLightBots, a class of subgram, sunlight-powered, untethered soft robots that achieve autonomous locomotion under continuous illumination near 1 Sun (100 mW/cm2). Their operation is enabled by a self-resetting snapping (SRS) mechanism that integrates liquid crystal elastomers (LCEs) with snap-through instability to accumulate solar energy supplied at low power, release it as rapid, high-power motion, and reset through photothermal-mechanical feedback. Through coordinated optimization of the LCE actuation temperature, photothermal conversion, actuation stress, and structural energy barrier, the system operates near 1 Sun and achieves a peak mass-specific mechanical power of 89 W/kg. At this irradiance, the optimized LCE generates an actuation stress of 0.1 MPa at approximately 60 deg C. SunLightBots demonstrate sustained swimming, crawling, and repeated impulsive jumping. Under 1.5 Suns, the swimmer advances more than three body lengths per cycle. This work provides a materials-mechanics route toward autonomous soft robots powered entirely by the environment.
BibTeX
@misc{lee2026sunlightbots,
  author = {Yoo Jin Lee and Melanie Torres Crespo and Zhongxiao Deng and Andrew Tejada-Vega and Rebecca Kramer-Bottiglio and Wenzhong Yan and Yimin Luo},
  title = {{SunLightBots: Turning sunlight into self-sustained, high-power motion in soft robots}},
  year = {2026},
  eprint = {2611.14729},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2611.14729},
}
Figure