Abstract
Graphene mechanical resonators are the ultimate two-dimensional nanoelectromechanical systems (NEMS) with applications in sensing and signal processing. While initial devices have shown promising results, an ideal graphene NEMS resonator should be strain engineered, clamped at the edge without trapping gas underneath, and electrically integratable. In this letter, we demonstrate fabrication and direct electrical measurement of circular SU-8 polymer-clamped chemical vapor deposition (CVD) graphene drum resonators. The clamping increases device yield and responsivity, while providing a cleaner resonance spectrum from eliminated edge modes. Furthermore, this resonator is highly strained, indicating its potential in strain engineering for performance enhancement.
Introduction
Graphene's unique mechanical and electrical properties make it an ideal candidate for next-generation nanoelectromechanical systems (NEMS). However, the path to practical application is hindered by significant fabrication hurdles. Traditional "doubly-clamped" rectangular resonators often suffer from spurious edge modes and parasitic vibrations from metal contacts, which clutter the resonance signal.
While circular "drum" resonators are theoretically superior, they are traditionally fabricated by depositing graphene over pre-patterned holes. This method frequently traps gas beneath the membrane, causing unwanted damping, and makes subsequent lithography for electrical integration nearly impossible without damaging the fragile, suspended graphene. This research introduces a novel "release-last" fabrication technique using SU-8 polymer as a top-clamping layer to create fully integrated, high-performance drum resonators.
Fabrication Methodology
The researchers developed a robust fabrication flow designed to maximize yield and enable strain engineering:
- Substrate Preparation: Highly resistive silicon or fused silica substrates with buried local gates were used. Chemical Mechanical Polishing (CMP) was employed to smooth the surface, ensuring optimal graphene adhesion.
- Graphene Transfer and Patterning: Large-grain CVD graphene was transferred onto the substrate and patterned into strips.
- The SU-8 Clamp: A 2 $\mu$m layer of SU-8 polymer was spin-coated directly on top of the graphene. A hole was then patterned in the SU-8 to define the specific drum area.
- Strain Engineering via Hard-Bake: The structure underwent a hard-bake at 170°C to cross-link the SU-8. As the polymer shrinks during this thermal process, it pulls the graphene taut, inducing significant built-in strain.
- Suspension: In the final step, the device was immersed in a buffered oxide etchant (BOE) to remove the sacrificial oxide layer beneath the graphene. This creates a suspended drum without the risk of trapped gas.
Key Results and Insights
Enhanced Yield and Responsivity
The SU-8 clamp acts as a rigid frame, providing the structural integrity necessary to place the graphene much closer to the gate (50 nm) than traditional methods allow. This proximity, combined with the ability to handle higher DC voltages (up to 10V compared to the typical 3V), leads to significantly higher responsivity. The SU-8 method achieved a device yield of over 70% for 50 nm gaps, a stark contrast to the <10% yield associated with standard fabrication techniques.
Spectral Purity
By clamping the graphene membrane on all sides, the researchers successfully eliminated "edge modes"—the vibrations from the loose sides of rectangular strips that typically plague NEMS devices. The resulting resonance spectra are remarkably clean, showing a regular series of resonant frequencies without the interference of independent metal contact resonances. Fundamental resonant modes as high as 260 MHz were recorded for 1.5 $\mu$m diameter drums.
Intentional Strain Engineering
While polymer shrinkage is often viewed as a defect in microfabrication, this study leveraged the thermal contraction of SU-8 to intentionally tension the graphene. The measured built-in strain ranged from 0.0023 to 0.004, which is an order of magnitude higher than what is typically achieved in room-temperature resonators.
Electrical Performance
Importantly, the SU-8 process proved to be "graphene-friendly." Field-effect mobility measurements remained high (~3000–6000 cm²/V-s), confirming that the polymer clamping does not degrade the electrical integrity of the CVD graphene.
Discussion and Future Outlook
Despite the significant gains in yield and spectral purity, the room-temperature Quality Factor (Q) was measured at approximately 60. This is lower than some optical-readout drum resonators, a trade-off likely caused by SU-8 residue, displacement current dissipation, or non-uniform strain (wrinkling).
Future work will focus on refining the processing steps to minimize residue and optimizing hard-bake parameters to further tune the strain. The ultimate objective is to push these resonators into the GHz range, targeting a Frequency-Quality (F·Q) product exceeding $10^{12}$ for high-performance sensing and signal processing applications.
Summary updated