Study on the Abrasive Retention Capacity on the Surface of Electroplated Diamond Wire Saw

Jintao Zheng, Qian Xie, Peiqi Ge, Jianfeng Meng, Wenbo BiResearch 2021 · DOI

Abstract

The quality and efficiency of slicing brittle materials like silicon are significantly compromised if diamond abrasives shed from the wire saw surface during operation. These abrasives are typically held by a nickel-plated layer, and their retention capacity is characterized by the plastic deformation at the interface. This study utilizes a finite element model of a double-cone diamond abrasive to investigate how residual compressive stress, plating hardness, and protrusion height affect retention. Results indicate that higher plating hardness enhances retention, while residual compressive stress and increased protrusion height diminish it. Experimental slicing of single-crystal silicon rods validated these findings, showing a shedding rate of 29.4%, closely matching theoretical predictions.

Introduction: The Challenge of Abrasive Shedding

In the semiconductor and photovoltaic industries, electroplated diamond wire saws are essential for slicing brittle materials into thin wafers. These tools consist of a high-strength steel core coated with a nickel layer that mechanically "locks" diamond abrasives in place.

SEM image of an electroplated diamond wire saw showing the nickel-plated layer and diamond abrasives.

The primary failure mode for these saws is abrasive shedding. When sawing forces exceed the mechanical retention capacity of the nickel layer, diamonds pull out, leading to reduced cutting efficiency and poor surface quality. This paper investigates the mechanical "occlusion" effect—the physical clamping of the diamond—and how the plating's internal properties influence this grip.

Diagram illustrating the debonding of a diamond abrasive from the plating layer.

Methodology

The researchers employed a dual-track approach combining simulation and physical testing:

  1. Finite Element Modeling (FEM): A 3D simulation of a "double-cone" diamond particle embedded in a nickel layer was created. The model used an equivalent cooling method to simulate residual stresses and converted Vickers hardness data into yield stress values. A "critical shedding state" was defined as reaching 8% plastic strain in the nickel layer.
  2. Experimental Validation:
    • Material Testing: X-ray diffraction measured residual stress, and nano-hardness testers characterized the nickel plating.
  3. Slicing Trials: Actual slicing of a 60mm single-crystal silicon rod was performed using a Meyer Burger RTD6800 multi-wire sawing machine.
  4. Topography Analysis: A wire saw topography analyzer counted diamonds before and after sawing across ten 1.5mm regions to calculate the actual shedding rate.

Key Insights and Results

The study revealed several critical factors influencing tool longevity:

  • The Hardness Advantage: Increasing the hardness of the nickel layer by approximately 108% resulted in a 23% increase in retention capacity. Harder plating better resists the plastic deformation that leads to diamond loss.
  • The Residual Stress Trap: Contrary to some mechanical applications, residual compressive stress in the plating is detrimental. It predisposes the nickel layer to reach the critical deformation threshold under load, reducing retention.
  • The Protrusion Trade-off: There is a direct conflict between cutting efficiency and tool life. Increasing the diamond's protrusion height by 61% (to improve cutting speed) decreased retention capacity by 31% due to the reduced "buried" surface area.
  • Predictive Accuracy: The theoretical model predicted a shedding rate of 24.6% (±1.55%), while experimental results showed a rate of 29.4%. This ~16% variance suggests the model is a viable tool for pre-production quality evaluation.

Conclusion

This research provides a mechanical roadmap for optimizing electroplating parameters. By balancing plating hardness against residual stress and protrusion height, manufacturers can produce longer-lasting, more efficient cutting tools for the high-precision silicon wafer industry. Future work will focus on modeling irregular diamond shapes and size distributions to further refine predictive accuracy.

Summary updated

Abstract

Abstract The quality and efficiency of slicing will be reduced if the abrasives on the surface of diamond wire saw shed in sawing. Generally, the diamond abrasives are held on the surface of electroplated diamond wire saw by a nickel-plated layer, and the abrasive retention state, reflecting abrasive shedding, can be characterized by the plastic deformation of the plating layer at the interface between the nickel-plated layer and the abrasive. To gain an in-depth understanding of the abrasive shedding mechanism, a finite element model of the double-cone diamond abrasive embedded in a nickel-plated layer was established in this paper to research the effects of the residual compressive stress and hardness of the nickel-plated layer as well as the protrusion height of the diamond abrasive on the abrasive retention capacity. The results show that the presence of the residual compressive stress in the nickel-plated layer resulted in the decrease of the abrasive retention capacity. And the higher hardness of the nickel-plated layer could enhance its abrasive retention capacity. Furthermore, the depth of the diamond abrasive inside the nickel-plated layer was decreased with the increase of its protrusion height, which would reduce the abrasive retention capacity. Based on the results of the finite element analysis, a calculation procedure of abrasive shedding rate was presented. Subsequently, the slicing experiment of a single crystal silicon rod was carried out by the Meyer Burger RTD6800 multi-wire sawing machine and the electroplated diamond wire saw with a core wire diameter of 65μm. The abrasive shedding rate of the diamond wire saw caused by sawing was analyzed theoretically and experimentally. The research work is of great significance to improve the quality detection and evaluation of electroplated diamond wire saw.
BibTeX
@inproceedings{zheng2021study,
  author = {Jintao Zheng and Qian Xie and Peiqi Ge and Jianfeng Meng and Wenbo Bi},
  title = {{Study on the Abrasive Retention Capacity\ on the Surface of Electroplated Diamond\ Wire Saw}},
  booktitle = {Research},
  year = {2021},
  doi = {10.21203/rs.3.rs-347682/v1},
}
Figure