Structural Performance of Highway Bridges under Given Foundation Settlements

Zhan Su, Qian Wang, Huanzi Wang2025 · DOI

TL;DR

This paper investigates how foundation settlements impact the structural integrity of concrete box girder bridges, a common highway design. By using finite element modeling, the authors demonstrate that factors like bridge skew and curvature significantly amplify the internal stresses caused by sinking piers, highlighting a gap in current design standards.

What Problem Does This Paper Address?

Soil settles. Whether due to consolidation, poor drainage, or heavy traffic, bridge foundations move over time. While geotechnical engineers provide estimates for these movements, structural engineers lack clear, quantitative guidelines in standards like AASHTO on what constitutes an "acceptable" settlement for the bridge superstructure itself.

Most existing research has focused on the "bump at the end of the bridge" (approach slabs), but this paper addresses the internal stresses induced in the actual bridge girders. Without understanding how geometry—like curves and skew angles—interacts with settlement, engineers cannot accurately predict if a bridge will remain safe or service-ready after its foundation shifts.

Methods

The researchers conducted a numerical parametric study using Finite Element (FE) analysis via the industry-standard software CSI-Bridge.

They modeled two specific types of cast-in-place posttensioned concrete box girder bridges:

  • Example 1 (EX1): A 3-span bridge (100'-150'-100').
  • Example 2 (EX2): A 2-span bridge (150' typical span).

The study varied three primary parameters to observe their impact on girder stress:

  1. Skew Angles: 0°, 15°, 30°, 45°, and 60°.
  2. Horizontal Curve Radii: 250 ft, 500 ft, 1,000 ft, and infinite (straight).
  3. Settlement Scenarios: 0.5-inch and 1.0-inch vertical settlements at one or two piers.

Datasets

The study does not use external datasets. Instead, it utilizes two representative bridge models (EX1 and EX2) designed to reflect typical California highway bridge construction standards.

Key Insights and Ideas

  • Skew is a Stress Multiplier: The most significant finding is that as the skew angle increases, the bridge becomes much more sensitive to settlement. The magnitude of stress change can effectively double as the skew moves from 0° to 60°.
  • The Curvature Threshold: The horizontal curve radius has a diminishing effect on settlement stress. Once the radius exceeds 500 feet, the bridge's response to settlement becomes nearly identical to that of a straight bridge.
  • Span Sensitivity: 3-span bridges are significantly more vulnerable to pier settlement than 2-span bridges. This suggests that continuous spans over multiple piers create more internal redundancy—and thus more internal stress—when one support drops.
  • Location of Failure: The maximum induced stresses (both tension and compression) consistently occur at the pier supports, identifying these as the critical zones for inspection after a known settlement event.

Key Results

  • Stress Magnitude: For 3-span bridges, a 1-inch settlement at a single pier increased girder stress by 20-40% relative to dead load stresses. For 2-span bridges, the increase was much lower, at 5-10%.
  • Skew Impact: In the 3-span model, increasing the skew from 0° to 60° raised the maximum stress change from roughly 40% to 60%.
  • Two-Pier vs. One-Pier: Simultaneous settlement of two piers generally induces higher stresses than a single-pier settlement, particularly when the skew angle is low (<40°) and the curve radius is large (>500 ft).

Limitations and Future Work

The authors acknowledge that this study is based on linear elastic analysis. In reality, concrete is a nonlinear material that experiences creep, shrinkage, and cracking over time, which could either mitigate or exacerbate these stresses.

Future research directions include:

  • Nonlinear Modeling: Incorporating concrete creep and shrinkage into the FE models.
  • Staged Construction: Simulating the bridge's life cycle more accurately.
  • Field Verification: The authors highlight a critical lack of field data to calibrate these models and propose actual bridge testing to verify their numerical findings.
  • Complex Movements: Expanding the study to include pier rotations and differential settlements.

Summary updated

Abstract

This paper presents a study of structural performance of highway bridges under given foundation settlements.The ultimate objective of this research is to analyze and develop acceptable levels of bridge foundation settlements under ultimate and service limit states, which are not adequately addressed in current bridge design standards.In order to design modern bridges to accommodate any expected foundation settlements, structural engineers need to consider foundation movements and quantify their impacts on the performance of bridge superstructures.In this paper, one type of widely used highway bridges, cast-in-place posttensioned concrete box girder bridges, is considered and settlement analyses are performed to study the induced bridge girder stresses due to foundation or pier settlements.Two sets of bridge examples are studied with different bridge skew angles and horizontal curve radii, to investigate the effects of these parameters.A state-of-art bridge analysis finite element (FE) program is used to analyze various bridge responses.It is shown that the bridge girder curvature and skew angle can impact the girder stresses due to foundation or pier settlements, and the trends are plotted using a numerical parametric study.Based on the evaluation of stress increase due to settlements, an acceptable pier settlement limit can be further determined based on allowable girder stresses in the next stage of the study.
BibTeX
@misc{su2025structural,
  author = {Zhan Su and Qian Wang and Huanzi Wang},
  title = {{Structural Performance of Highway Bridges under Given Foundation Settlements}},
  year = {2025},
  doi = {10.18260/1-2-1153-53946},
}
Figure