TL;DR
This paper compares two methods for compressing high-power laser pulses: hollow-core fiber (HCF) and multi-pass cell (MPC). While both achieve shorter pulses, the HCF surprisingly improves beam quality, making it superior for applications like generating extreme ultraviolet (XUV) light, despite lower efficiency than the MPC.
What Problem Does This Paper Address?
Modern scientific applications, from materials processing to attosecond science, demand laser pulses with extremely high peak power and short durations. While Ytterbium (Yb)-doped fiber lasers are excellent for generating high average power, their inherent gain bandwidth limits pulse durations to hundreds of femtoseconds, which is too long for many cutting-edge applications. To overcome this, researchers use post-compression techniques to shorten these pulses further. However, simply shortening pulses isn't enough; the quality of the laser beam, particularly its spatial wavefront, is critical for applications like high harmonic generation (HHG), which are used to create coherent extreme ultraviolet (XUV) light. This paper addresses the need to understand how different post-compression techniques affect both the temporal (pulse duration) and spatial (beam quality) characteristics of these high-power laser pulses, and how these characteristics impact downstream applications like XUV generation.
Methods
The researchers compared two primary post-compression techniques:
- Gas-filled Hollow-Core Fiber (HCF): A 1.35-meter long fiber filled with argon gas. The laser pulse propagates through this fiber, undergoing self-phase modulation (SPM) which broadens its spectrum. This broadened spectrum is then recompressed using chirped mirrors.
- Multi-Pass Cell (MPC): A Herriott-type optical cavity designed for multiple reflections (28 round trips in this case) of the laser beam. Similar to the HCF, argon gas within the MPC induces SPM for spectral broadening, followed by compression with chirped mirrors.
Both systems were driven by a commercial 70W Yb-doped fiber laser producing 230 fs pulses. The researchers meticulously characterized the output of each system by measuring:
- Temporal pulse duration: Using an autocorrelator.
- Spectral bandwidth: Using a spectrometer.
- Spatial beam profile and wavefront quality: Using a Shack-Hartmann wavefront sensor.
- Efficiency: Measuring the throughput of each system.
- High Harmonic Generation (HHG) performance: Using the compressed pulses to generate XUV light and comparing the resulting photon flux.
Datasets
Not discussed in the paper. The experiments utilize a commercial Yb-doped fiber laser as the input source and argon gas as the nonlinear medium.
Key Insights and Ideas
- HCF as a "Spatial Filter": Surprisingly, the HCF not only compressed the pulse but also acted as a modal filter, improving the beam's spatial wavefront quality. This is a significant advantage over the MPC.
- MPC's Aberration Accumulation: The multiple reflections within the MPC, while efficient for spectral broadening, led to a cumulative build-up of aberrations, particularly astigmatism, degrading the wavefront quality.
- Wavefront Quality Dominates HHG Flux: Even though the MPC produced higher pulse energy, the HCF's superior beam quality resulted in a significantly higher photon flux in the generated XUV spectrum. This highlights that for applications like HHG, beam quality is as crucial as pulse energy.
- Pressure-Mediated Tuning: The spectral broadening in both HCF and MPC systems is critically dependent on gas pressure, offering a way to tune the output spectrum.
Key Results
- HCF: Achieved 27 fs pulses from 230 fs input with >50% efficiency. It also improved wavefront quality, reducing PV and RMS values by over a factor of two.
- MPC: Achieved 34 fs pulses with significantly higher efficiency (>88%). However, it introduced wavefront aberrations, notably increasing astigmatism 45°.
- HHG Comparison: The HCF-driven HHG produced approximately 2.5 times higher photon flux compared to the MPC-driven HHG, despite the MPC having higher single pulse energy.
Limitations and Future Work
- Limitations:
- The MPC's efficiency, while high, showed a slight monotonic decrease with increasing input power, potentially due to thermal effects.
- The MPC's wavefront degradation is a significant drawback for applications requiring pristine beam quality.
- Future Work:
- The authors suggest using the HCF as a single compressor or as an output component in a cascaded compressor for further improvement of spatial wavefront quality.
- They propose integrating adaptive optics to pre-compensate for wavefront distortions, enabling active tailoring of the XUV beam properties.
- A cascaded MPC and HCF configuration is mentioned as a promising avenue for achieving superior spatiotemporal beam quality for few-cycle pulses.
- The pressure-dependent spectral broadening could be leveraged to create tunable XUV sources.
Summary updated