Abstract
Mycelium, the root-like structure of fungi, represents a sustainable and regenerative material with unique electrical and biological properties. While localized electrical activity in fungi is well-documented, its potential as a distributed biosensor for structural health monitoring (SHM) requires a deeper understanding of how signals propagate across its network. This study introduces an electrical impedance network model combined with the inhomogeneous wave correlation (IWC) method to characterize the spatiotemporal dispersion behavior of living mycelium. Our findings reveal that mycelium acts as a frequency-dependent, ionic conductor that exhibits macroscopic homogeneity and isotropy at low-to-mid frequencies. We demonstrate that moisture content is the critical factor for signal transmission, laying the groundwork for mycelium-based "living sensors" in green infrastructure.
Introduction
As the demand for sustainable building materials grows, fungal mycelium has emerged as a promising candidate for "smart" bio-composites. Beyond its structural potential, mycelium is electrically active, responding to environmental stimuli such as mechanical stress, humidity, and light. However, utilizing mycelium as a functional component in self-sensing systems requires moving beyond the observation of localized "spikes" or action potentials.
To integrate fungi into distributed sensor networks, we must understand the spatial and temporal dynamics of signal propagation. Specifically, how does an electrical input injected at one point travel, attenuate, and disperse across the physical geometry of the fungal network? This research addresses this gap by developing the first rigorous mathematical model to describe spatial wave propagation in living fungi, treating the biological network as a complex electrical circuit.
Methodology
Material Preparation and Actuation
The researchers cultivated Pleurotus ostreatus (oyster mushroom) on agricultural waste substrates. Once a uniform mycelium skin had formed, the sample was prepared for electrical characterization. To map signal propagation, a broadband sweep voltage (ranging from 1 Hz to 500 kHz) was injected at the center of the mycelium block. The response was captured using 16 pairs of subdermal needle electrodes arranged in a radial pattern, allowing for the measurement of voltage across various distances and angular orientations.
Theoretical Modeling
The study modeled the mycelium using transmission line theory. By treating the fungal network as a distributed-parameter impedance network, the material was mathematically decomposed into infinitesimal segments characterized by resistance ($R$), capacitance ($C$), and conductance ($G$).
To bridge the gap between experimental voltage data and this theoretical model, the team employed the Inhomogeneous Wave Correlation (IWC) method. Originally developed for acoustics and elastic wave propagation in solids, the IWC method allowed the researchers to extract complex wavenumbers. These wavenumbers are essential for quantifying how electrical waves disperse (change speed with frequency) and decay (attenuate) as they move through the mycelium.
Key Insights and Results
Ionic vs. Electromagnetic Conduction
A pivotal discovery of this study is the mechanism of conduction. The researchers found that signal propagation is almost entirely dependent on the aqueous environment within the living fungus. When the mycelium was dehydrated, signal propagation ceased; upon rehydration, the electrical response was restored. This confirms that the signals are carried by moving ions within the moisture-rich hyphae—similar to biological signaling in animal neural tissues—rather than through electromagnetic wave propagation typical of dry dielectric materials.
Frequency-Dependent Attenuation
Mycelium behaves effectively as a low-pass filter. The network naturally attenuates higher frequencies and signals traveling over longer distances due to its lossy, dielectric nature. For instance, the dispersion analysis revealed an exponential signal attenuation of approximately -174 dB per unit length at 50 kHz. This suggests that for practical sensing applications in large-scale structures, low-frequency signals are the most viable for long-range communication within the fungal network.
Macroscopic Homogeneity
While a microscopic view of mycelium reveals a chaotic and porous web of branching hyphae, the study found that at a macroscopic scale, the material is surprisingly predictable. At low-to-mid frequencies, the electrical response is uniform across different directions. The standard deviations of the fitted electrical parameters across 12 different directional angles (0° to 330°) were significantly smaller than their mean values. This macroscopic isotropy is a crucial finding, as it simplifies the design of sensors by allowing engineers to treat the material as a homogeneous medium.
Discussion and Limitations
While the model successfully characterized the material, some limitations remain. The analytical dispersion model assumes an infinite medium, which leads to minor discrepancies when applied to the finite boundaries of experimental laboratory samples. Additionally, the current model assumes constant impedance parameters, though real-world dielectric properties may vary slightly with frequency. High-frequency measurements also faced challenges due to the extreme damping nature of the fungus, which can submerge signals in noise at great distances.
Conclusion
This research provides a foundational framework for the spatial and temporal characterization of living mycelium. By quantifying how signals degrade and disperse, we can now move toward designing precise, mycelium-based sensing systems. These living networks offer a path toward sustainable, self-repairing, and carbon-sequestering structural health monitoring systems, where the building material itself acts as the nervous system of the infrastructure.
Summary updated