Abstract
Graphene monoliths with high porosity inherit extraordinary properties of graphene and establish a versatile platform to integrate diverse materials for multifunctional applications. To date, many methods have been invented to prepare graphene monoliths, including freeze-drying and templating, but these predominantly rely on fluid-based process. Direct thermoplastic foaming for graphene monoliths, as seen in the polymer industry, remains undeveloped. Here, we demonstrate a direct thermoplastic foaming strategy of a graphene monolith with high elasticity and multifunctionality. The intercalation of polymers enables the thermal plasticity of graphene oxide complex solids and allows precise control of the cellular structure of the graphene monolith. The direct thermoplastic foaming method is applicable to graphene monolith bulks, 3D-printed structures, and other 2D-nanosheets monoliths. This approach provides a facile, nontoxic, rapid and low-cost route for the industrial production of monoliths comprising graphene and various nanomaterials.
Introduction
Graphene monoliths (GMs), including foams and aerogels, are highly prized for their lightweight nature, extreme elasticity, and excellent electrical and thermal conductivity. However, traditional production methods like freeze-drying or hydrothermal assembly are "fluid-based," requiring large volumes of solvent and long processing times, which often lead to structural defects during scale-up.
In the polymer industry, foams are typically manufactured via direct foaming, where gas expands within a molten matrix. This approach has been difficult to adapt for 2D materials like graphene because strong interlayer attractions make the solid precursors brittle. Instead of expanding smoothly, these materials tend to fracture under pressure. This study introduces a "solvent-free thermoplastic foaming" (TPF) strategy to transform rigid graphene oxide (GO) solids into a plastic state, enabling rapid expansion into high-performance monoliths.
Methods: Thermoplastic Foaming (TPF) Strategy
The researchers developed a Non-solvent Thermoplastic Foaming (TPF) strategy consisting of three primary stages. First, a solid precursor is prepared by mixing GO sheets with a polymer plasticizer, specifically Polyethylene Glycol (PEG), and physically expandable microspheres.
Second, the solid is heated to approximately 100–120°C. During this stage, PEG intercalates between the GO layers, increasing the interlayer spacing and allowing the sheets to slide past one another—a phenomenon termed "plastic slippage." Simultaneously, the microspheres expand, pushing the now-plastic GO matrix into a stable honeycomb-like cellular structure. Finally, the foam undergoes high-temperature annealing at 1600°C to remove the PEG and microspheres while healing the graphene lattice to ensure high crystallinity.
Key Insights and Mechanism
A critical discovery in this process is the "plasticity threshold." The researchers identified that an interlayer spacing of $d \approx 1.32$ nm is required for the GO complex to behave like a thermoplastic. If the PEG concentration is too low (weight ratio $\alpha < 0.7$), the material remains brittle and fails during expansion.
As the microspheres grow, the internal pressure ($P_{in}$) overcomes external pressure ($P_a$), causing the cells to evolve from spherical to polygonal shapes. This impingement creates "Plateau borders," resulting in a continuous and stable honeycomb architecture. This method is not limited to graphene; it was successfully applied to other 2D materials, including Boron Nitride, MXene, and Montmorillonite, proving its universality.
Results and Performance
The GMs produced via TPF exhibit remarkable mechanical and functional properties:
- Superelasticity: The monoliths show near-perfect recovery (>95% strain) even after 1,000 compression cycles at 90% strain, with significantly lower plastic deformation (~0.6%) compared to traditional freeze-dried versions.
- High Conductivity: Post-annealing, the monoliths reach an electrical conductivity of $8.0 \times 10^3$ S/m and a thermal conductivity of $44.9$ W/m·K.
- Efficiency and Scalability: The foaming process itself takes less than one minute, a massive speedup compared to the days required for freeze-drying. The team demonstrated the fabrication of large-scale 100 mm x 100 mm stacks and complex 3D-printed microlattices.
Conclusion and Future Outlook
The TPF method provides a rapid, low-cost, and scalable alternative to traditional fluid-based synthesis. While the 1600°C annealing step is energy-intensive and the monoliths currently have a relatively low BET surface area due to dense cell walls, the strategy represents a major step toward industrial-scale production. Future work will focus on introducing hierarchical nanopores within the cell walls and exploring lower-temperature reduction methods to improve sustainability.
Summary updated