Simulation of Active Compensated Pulsed Alternator with a Laser Flashlamp Load Based on Simplified Model

Yuan Pei, Kexun Yu, Caiyong Ye, Zhangao RenJournal of International Conference on Electrical Machines and Systems 2012 · DOI

Introduction

High-power laser systems typically require massive energy bursts—tens of kilojoules—delivered within a precise window of 400 to 600 microseconds. Traditionally, this demand is met by large banks of capacitors. While effective, these capacitor groups are bulky and heavy, necessitating complex charging and discharging circuitry that limits the mobility of high-power laser applications.

This paper explores a nontraditional power system using an Active Compensated Pulsed Alternator (ACPA) to drive a flashlamp directly. By leveraging the high energy density of the ACPA, the system's overall volume can be significantly reduced.

The proposed ACPA-based laser power system eliminates the need for bulky capacitor groups.

The Challenge of Load Matching

The primary hurdle in replacing capacitors with an alternator is "matching" the machine's output to the specific resistive load of a laser flashlamp. Unlike a steady-state generator, the ACPA must produce a single, high-intensity pulse. If the pulse width or amplitude deviates from the laser's requirements, the system fails to fire efficiently. To address this, the researchers developed a simplified circuit-based simulation model to analyze and optimize the interaction between the ACPA and the flashlamp.

Simulation Methodology

The authors modeled the ACPA as an equivalent circuit featuring a sinusoidal voltage source in series with a variable internal inductance ($L(t)$) and internal resistance ($R_i$). The variable inductance is a result of "flux compression" achieved via a compensating coil.

The laser flashlamp was modeled as a non-linear variable resistor, focusing on the main current buildup phase. The simulation explored three critical parameters:

  1. Trigger Angle ($\theta$): The rotor's position at the start of the pulse.
  2. Compensating Angle ($\delta$): The electrical angle between the compensating and field windings.
  3. Compression Ratio ($\rho$): The ratio of maximum to minimum inductance, representing the machine's ability to "squeeze" magnetic flux.

Key Insights and Results

The simulation results provide a roadmap for optimizing ACPA performance for laser loads:

  • Optimal Timing: Maximum peak current is achieved when both the trigger angle ($\theta$) and the compensating angle ($\delta$) are set to zero. Any deviation leads to a significant drop in output amplitude.
  • Pulse Width Control: The compression ratio ($\rho$) is the primary mechanism for pulse shaping. As shown in the simulation results, increasing $\rho$ narrows the pulse width, which is essential for meeting the microsecond-scale requirements of the flashlamp.
Simulation results showing how increasing the compression ratio (ρ) narrows the output pulse width to meet laser requirements.
  • Load Dominance: The flashlamp's own impedance ($K_0$) was found to have a more profound impact on system adaptation than the machine's compression ratio. Higher impedance shifts the peak current timing, requiring adjustments in external control circuitry.
  • Diminishing Returns: While increasing the compression ratio helps narrow the pulse, the gains in peak amplitude diminish at very high ratios (e.g., doubling $\rho$ from 50 to 100), suggesting a practical limit for machine design.

Conclusion

By developing a simplified simulation model, this research demonstrates that an ACPA can effectively drive a laser flashlamp without the need for bulky capacitors. The findings regarding optimal angles and compression ratios provide critical guidance for the design and control of future, more mobile high-power laser systems. While the model simplifies certain ignition phases, it establishes a robust foundation for moving toward physical prototypes and dynamic control systems.

Summary updated

Abstract

This paper presents a nontraditional laser power system in which an active compensated pulsed alternator (ACPA) drives a flashlamp directly without the use of capacitor groups. As a result, the volume of the laser system is decreased because of the high energy density of the ACPA. However, the difficulty in matching the output of the alternator with the laser flashlamp is a significant issue and needs to be well analyzed. In order to solve this problem, based on the theory for ACPA, the authors propose a simplified model for the system of ACPA with flashlamp load by the way of circuit simulation. The simulation results preliminarily illuminate how the performance of the ACPA laser power system is affected. Meanwhile, the simulation results can also supply a consultation for future ACPA laser power system design and control.
BibTeX
@article{pei2012simulation,
  author = {Yuan Pei and Kexun Yu and Caiyong Ye and Zhangao Ren},
  title = {{Simulation of Active Compensated Pulsed Alternator with a Laser Flashlamp Load Based on Simplified Model}},
  journal = {Journal of International Conference on Electrical Machines and Systems},
  year = {2012},
  doi = {10.11142/jicems.2012.1.4.434},
}
Figure