TL;DR
This paper introduces a novel Dual-Differential D-dot overvoltage sensor designed for accurate, non-contact measurement of transient overvoltages in power grids. By employing a Field-Circuit Coupling method for sensor design and optimization, they achieved a sensor with fast response, minimal phase and amplitude errors, and improved immunity to external interference.
What Problem Does This Paper Address?
Accurate measurement of overvoltages in high-voltage power grids is crucial for studying their characteristics, designing insulation coordination, and ensuring the safe and stable operation of substations and transmission lines. However, overvoltages are often characterized by large amplitudes and high frequencies, making them difficult to measure reliably. Existing methods like resistance dividers have limitations in thermal capacity and accuracy for high-frequency signals, while optical fiber sensors face challenges with reliability and environmental stability. D-dot sensors, while promising for non-contact measurement, traditionally have limited bandwidth and can be susceptible to interference. This paper addresses the need for a sensor that is accurate, fast, has a wide bandwidth, is robust against interference, and is convenient to install for capturing overvoltage waveforms and parameters.
Methods
The core innovation lies in the Field-Circuit Coupling method for sensor design and parameter optimization. This approach involves:
- Electromagnetic Field Simulation: Using Ansoft Maxwell to model the power transmission line and the sensor, simulating the electric field distribution around the line when the sensor is present.
- Equivalent Circuit Modeling: Developing a detailed equivalent circuit of the Dual-Differential D-dot sensor in Simplorer, incorporating mutual and stray capacitances.
- Joint Simulation and Iterative Optimization: Linking the electromagnetic field simulation with the circuit simulation. The electric field data from Maxwell is used as input for the Simplorer model. The sensor's structural parameters (outer radius, electrode distance, width, and thickness) are iteratively adjusted in Maxwell, and the resulting output voltage and phase difference are analyzed in Simplorer. The optimization target is to minimize the phase difference (ideally < 1°) between the input and output signals.
- Dual-Differential Structure: The sensor itself employs a dual-differential design with four electrodes. This configuration enhances its ability to capture weak electric fields and, importantly, suppresses common-mode interference by amplifying differential signals.
Datasets
Not discussed in the paper. The study relies on simulations and experimental verification using a custom-built test platform.
Key Insights and Ideas
- Field-Circuit Coupling as a Design Paradigm: The paper demonstrates that integrating electromagnetic field simulations with circuit simulations is a powerful method for optimizing sensor parameters, overcoming the "blindness" and "unquantifiable parameters" often encountered in traditional sensor design.
- Dual-Differential for Robustness: The dual-differential structure significantly improves the sensor's immunity to external electromagnetic interference, a critical factor in noisy power grid environments.
- Non-Contact Measurement Capability: The sensor effectively measures voltage without direct electrical connection to the transmission line, enhancing safety and simplifying installation.
- Broadband Overvoltage Measurement: The sensor's design and validated performance indicate its suitability for measuring both steady-state and transient overvoltage signals across a wide frequency range.
Key Results
- Steady-State Performance: The sensor demonstrated excellent steady-state performance, with waveform distortion and phase differences comparable to a high-voltage probe. Ratio errors were consistently below 0.8%, and phase errors were less than 0.7°.
- Transient Performance: The sensor exhibited a fast response time to lightning impulse voltages, with peak response times similar to a high-voltage probe. Relative errors in peak response time were less than 1.7%, and peak error was less than ±1.9%, indicating accurate capture of transient overvoltages.
- Electromagnetic Field Distortion: The introduction of the sensor caused minimal distortion to the electric field around the transmission line (2.499% distortion rate), ensuring it doesn't significantly alter the phenomenon it's measuring.
- Insulation Strength: The sensor's epoxy resin insulation material has a breakdown strength of 35 MV/m, which is sufficient for the intended high-voltage applications.
Limitations and Future Work
- Limitations:
- The paper focuses on a single-phase transmission line model. Extending the simulation and testing to three-phase systems might be necessary for real-world applications.
- While the sensor is designed for non-contact measurement, the paper doesn't extensively discuss the practical challenges of mounting and maintaining its position relative to the transmission line in diverse environmental conditions.
- Future Work:
- The authors suggest that the Field-Circuit Coupling method can serve as a reference for designing other types of sensors.
- Further investigation into the sensor's performance in more complex electromagnetic environments and under various types of overvoltage transients could be beneficial.
- Exploring miniaturization and integration into existing power system infrastructure would be a logical next step.
Summary updated