Simulation Analysis of Thermal Deformation and Extruded Profile Formability of Al–10Mg–3Zn Aluminum Alloy

Guanmei Niu, Wr Li, Kaidi Jiang, Yang Yang, Guojun Wang, C. Karen Liu, Linzhong ZhuangMaterials 2026 · DOI

TL;DR

This paper investigates the hot deformation and extrusion of Al-10Mg-3Zn aluminum alloy, developing a strain-compensated constitutive model and hot processing maps to predict optimal processing parameters. By optimizing billet temperature, extrusion speed, and ingot length using response surface methodology, they achieved a significant reduction in extrusion load and improved profile quality, paving the way for wider application of these lightweight alloys.

What Problem Does This Paper Address?

High-Mg aluminum alloys, like Al-10Mg-3Zn, are crucial for lightweighting in industries such as transportation. However, their excellent properties come with challenges during hot working, particularly extrusion. These include high deformation resistance, leading to defects like cracking, stalling, and surface imperfections. Traditional trial-and-error methods for optimizing extrusion parameters are time-consuming and costly. This paper aims to address this by providing a scientifically grounded approach to understanding the alloy's hot deformation behavior and optimizing extrusion parameters to ensure successful and efficient manufacturing of complex profiles.

Methods

The researchers employed a multi-pronged approach:

  • Hot Compression Testing: They conducted extensive hot compression tests on Al-10Mg-3Zn alloy across a range of temperatures (300-450 °C) and strain rates (0.001-10 s⁻¹). This generated true stress-strain curves.
  • Temperature Correction: They identified and corrected for adiabatic heating during high-strain-rate compression, which significantly affects flow stress measurements.
  • Constitutive Modeling: A strain-compensated Arrhenius constitutive model was developed to accurately describe the alloy's flow stress behavior as a function of temperature, strain rate, and strain. This involved fitting polynomial functions to material constants.
  • Hot Processing Maps: Using the Dynamic Material Model (DMM) theory, they constructed hot processing maps that delineate safe processing zones from unstable regions prone to defects.
  • Finite Element Analysis (FEA): A steady-state extrusion simulation model was established using Qform software to analyze the influence of various process parameters on extrusion formability.
  • Response Surface Methodology (RSM): A Box-Behnken experimental design was used to systematically investigate the effects of billet temperature, extrusion speed, and ingot length on key output variables (extrusion load, velocity deviation, average strain, and temperature difference). This allowed for multi-objective optimization.

Datasets

The primary dataset used in this study was generated through experimental hot compression tests conducted on Al-10Mg-3Zn alloy. The chemical composition of the alloy was analyzed using a direct-reading spectrometer. The experimental data from these tests, along with simulation results from the FEA, formed the basis for the constitutive modeling and response surface analysis. No pre-existing public datasets were explicitly mentioned as being used for training or evaluation.

Key Insights and Ideas

  • Positive Strain Rate Sensitivity: The alloy's flow stress increases with strain rate and decreases with temperature, a characteristic that needs careful management during hot working.
  • Adiabatic Heating is Critical: At high strain rates, the temperature rise within the sample is substantial and can significantly alter the measured flow stress, necessitating accurate temperature correction for reliable modeling.
  • Hot Processing Maps are Predictive: The developed processing maps accurately predict regions of instability (e.g., cracking) at specific temperature and strain rate combinations, providing crucial guidance for safe processing.
  • Extrusion Speed is a Dominant Factor: Extrusion speed has a more significant impact on the temperature distribution and uniformity of the extruded profile than billet temperature.
  • RSM for Multi-Objective Optimization: Response surface methodology proved effective in finding a balance between competing objectives like minimizing extrusion load and ensuring uniform flow, leading to a practical optimization strategy.

Key Results

  • Optimal Hot Processing Window: A safe processing temperature range of 360–420 °C and a strain rate range of 0.004–0.123 s⁻¹ were identified.
  • Optimized Extrusion Parameters: The optimal parameters determined by RSM were: billet temperature of 400 °C, extrusion speed of 0.20 mm/s, and ingot length of 350 mm.
  • Reduced Extrusion Load: Under optimized conditions, the predicted extrusion load was 73.29 MN, a significant reduction compared to initial simulations (94 MN). This represents a reduction of over 22%.
  • Improved Profile Quality: The optimized parameters resulted in a velocity deviation of 24.96% and a cross-sectional temperature difference of 9.48 °C, indicating improved uniformity.
  • Model Validation: The predicted values from the RSM model showed good agreement with FEA simulations and experimental results, with extrusion load prediction errors less than 5%.

Limitations and Future Work

  • Velocity Deviation Discrepancy: While the extrusion load and temperature difference predictions were highly accurate, the model for velocity deviation showed a larger discrepancy (less than 17%). The authors suggest that optimizing die structure, rather than just extrusion parameters, might be crucial for further improving extrusion flow velocity uniformity.
  • Friction Model Simplification: The study used a simplified friction model. Future work could explore more complex friction models for even greater accuracy.
  • Material Variability: The study focused on a specific Al-10Mg-3Zn alloy composition. Further research could investigate the impact of minor compositional variations on hot deformation behavior and extrusion formability.
  • Die Design Optimization: The authors hint that die design plays a significant role in flow uniformity, suggesting this as a key area for future investigation.

Summary updated

Abstract

To investigate the hot deformation characteristics of the Al-10Mg-3Zn alloy, a series of hot compression tests was carried out using a Gleeble-3500 simulator. The experimental matrix covered temperatures of 300-450 °C and strain rates from 0.001 to 10 s<sup>-1</sup>. The true stress-strain curves were obtained and the hot processing map of the alloy was constructed based on the Dynamic Material Model principle. The multi-objective optimization of the extrusion process parameters was performed using the response surface method. The results showed that the flow stress of Al-10Mg-3Zn alloy increased with the increase in the strain rate and decreased with the increase in the deformation temperature, indicating that the alloy had a positive strain rate sensitivity. A strain-compensated Arrhenius constitutive model and a hot processing map of Al-10Mg-3Zn alloy were established based on the temperature-corrected data; here, the optimal temperature range and strain rate range for hot processing were specified. The optimal extrusion process parameters, determined by the response surface method, were as follows: billet temperature of 400 °C, extrusion speed of 0.20 mm/s, and ingot length of 350 mm. With this parameter combination, the simulation predicted an extrusion load of 73.29 MN, a velocity deviation of 24.96%, and a cross-sectional temperature difference of 9.48 °C for the profile. The predicted values from the response surface method were highly consistent with those from the finite element simulation. The optimized process parameters significantly reduced the extrusion load of the profile.
BibTeX
@inproceedings{niu2026simulation,
  author = {Guanmei Niu and WR Li and Kaidi Jiang and Yang Yang and Guojun Wang and C. Karen Liu and Linzhong Zhuang},
  title = {{Simulation Analysis of Thermal Deformation and Extruded Profile Formability of Al–10Mg–3Zn Aluminum Alloy}},
  booktitle = {Materials},
  year = {2026},
  doi = {10.3390/ma19020375},
}
Figure