SEU Mechanism and RHBD Strategy for the Set Circuit in a DICE Flip-Flop

Ye Liu, Guo Hong-Xia, Zhang Hong, Liu Xiang-Yuan, Ding Li-Li, Liu Ze-Teng, Lai Shan-Kun, Li Yun-FeiActa 2026 · DOI

TL;DR

Researchers have identified a critical "weak link" in radiation-hardened DICE flip-flops: the auxiliary set-control circuitry. By implementing a spatially redundant set-signal path, they successfully eliminated Single Event Upsets (SEUs) in a 40nm process, achieving zero errors under heavy-ion simulation with a manageable ~14% overhead in area and power.

What Problem Does This Paper Address?

In the harsh environment of space, high-energy particles (cosmic rays) can strike semiconductor devices, causing Single Event Effects (SEE). A common issue is the Single Event Upset (SEU), where a bit of data in a flip-flop flips from 0 to 1 or vice versa. To combat this, engineers use Radiation Hardening By Design (RHBD), specifically the Dual Interlocked Storage Cell (DICE) architecture, which uses redundancy to self-correct errors.

However, most research focuses on the storage core itself. This paper highlights a neglected vulnerability: the "Set" circuit. Even if the storage core is hardened, a particle strike on the control path that tells the flip-flop to "set" to high can generate a Single Event Transient (SET)—a momentary false pulse. This pulse can "trick" the hardened core into changing state, effectively bypassing its built-in protections.

Methods

The authors employed a sophisticated multi-level simulation framework to analyze and fix this vulnerability in a SMIC 40nm process:

  1. TREES Simulation: Used for full-layout heavy-ion strike scanning. It maps the physical layout to identify "hotspots" where a particle strike is most likely to cause a failure.
  2. TCAD-Calibrated SPICE: The researchers used Technology Computer-Aided Design (TCAD) to model the physical physics of a particle strike on a transistor. They then used these precise current models in SPICE (circuit simulation) to see how the resulting voltage pulses propagate through the logic.
  3. Redundant Design: They proposed a "set-redundancy" scheme. Instead of one set signal, they created two separate paths (S1 and S2) that are physically separated on the chip layout. Because they are far apart, a single particle strike is unlikely to affect both simultaneously.

Datasets

As this is a hardware design and simulation paper, it does not use traditional machine learning datasets. Instead, the "data" consists of:

  • Layout Strike Locations: 1,691 discrete strike points for the baseline design and 1,919 points for the hardened design.
  • Simulation Parameters: Heavy-ion strikes with a Linear Energy Transfer (LET) of 37 MeV·cm²/mg, representing a typical harsh space environment.
  • Process Node: SMIC 40 nm CMOS technology models.

Key Insights and Ideas

  • The "System Shortcut": The most significant insight is that the control logic (Set/Reset) can act as a "shortcut" for radiation-induced errors. Hardening the storage core is useless if the "Set" button can be pushed by a stray ion.
  • Spatial Isolation is Key: The researchers found that simply adding a second signal isn't enough; the two paths must be physically separated in the layout (spatial redundancy) to prevent "charge sharing," where a single strike spreads its energy across both paths.
  • Leveraging DICE Self-Recovery: By splitting the set signal, a strike on one path only affects one node of the DICE core. Because the DICE architecture is designed to recover from single-node upsets, it automatically ignores the false "set" pulse.

Key Results

The proposed RHBD strategy showed dramatic improvements in reliability:

  • Error Elimination: In the baseline design, 18 specific strike locations caused an SEU. In the hardened redundant design, zero SEUs were observed across all 1,919 strike locations.
  • SEU Cross-Section: The sensitive area (cross-section) dropped from $1.7 \times 10^{-9} \text{ cm}^2$ to zero.
  • Manageable Overhead: The hardening came at a cost of a 14.3% increase in area and a 14.5% increase in power consumption.
  • Timing Stability: Critical timing parameters (like signal delay) remained largely unaffected, making it a practical drop-in replacement for standard cell libraries.

Limitations and Future Work

While the simulations are promising, the authors note a few areas for further exploration:

  • PVT Variations: The current study focused on specific conditions. Future work needs to account for variations in Process, Voltage, and Temperature (PVT) to ensure the design is robust across all operating envelopes.
  • Monte Carlo Analysis: To further refine the reliability statistics, more extensive Monte Carlo simulations (randomized strike variables) are suggested.
  • Physical Validation: The ultimate test will be fabricating the design on a test chip and subjecting it to actual heavy-ion beam testing in a laboratory.

Summary updated

Abstract

标准单元库是芯片设计的基础,对其进行有效的抗辐照加固设计与验证是保障宇航电子系统在轨可靠运行的关键。本文以双互锁存储单元触发器为研究对象,系统分析了其在置位冗余加固前后的单粒子翻转效应。研究发现,未加固的双互锁存储单元触发器在重离子入射时可能因置位信号受单粒子瞬脉冲干扰而引发单粒子翻转;而通过置位冗余加固后,其两路置位信号可有效避免同时受到单粒子瞬态的干扰,并利用双互锁存储单元结构的自恢复机制实现对节点电压异常的自动纠正,显著提升了抗单粒子翻转能力。本文冗余加固设计技术及单粒子仿真方法可为标准单元库的抗辐照设计及验证提供有效技术路径,有助于缩短宇航元器件研发周期,推动航空航天电子系统的发展。
BibTeX
@inproceedings{liu2026seu,
  author = {Ye Liu and Guo Hong-Xia and Zhang Hong and Liu Xiang-Yuan and Ding Li-Li and Liu Ze-Teng and Lai Shan-Kun and Li Yun-Fei},
  title = {{SEU Mechanism and RHBD Strategy for the Set Circuit in a DICE Flip-Flop}},
  booktitle = {Acta},
  year = {2026},
  doi = {10.7498/aps.75.20251574},
}
Figure