Separation Flow Control of a Generic Ground Vehicle Using an SDBD Plasma Actuator

Hui Zheng, Xingjun Hu, Peng Guo, Zewei Wang, Jingyu WangEnergies 2019 · DOI

TL;DR

This paper investigates the use of Surface Dielectric Barrier Discharge (SDBD) plasma actuators for aerodynamic drag reduction on a generic ground vehicle (Ahmed body). Researchers found that strategically placing the actuator and optimizing its voltage can significantly reduce drag, particularly at lower speeds, by controlling flow separation.

What Problem Does This Paper Address?

As fuel efficiency regulations tighten and the demand for longer electric vehicle ranges increases, reducing aerodynamic drag on vehicles has become crucial. Traditional passive methods for drag reduction are reaching their limits. This paper explores active flow control, specifically using SDBD plasma actuators, to manipulate airflow around a vehicle and decrease drag, offering a potential avenue for further improvements. The study focuses on the complex wake flow of an Ahmed body, a common benchmark for vehicle aerodynamics, to understand the effectiveness and mechanisms of plasma-based drag reduction.

Methods

The study employed a multi-faceted experimental approach:

  • Quiescent Flow Tests: These tests were conducted to characterize the "ionic wind" produced by the SDBD plasma actuator. Particle Image Velocimetry (PIV) was used to measure the induced velocity field at various excitation voltages.
  • Wind Tunnel Experiments: A 1:60 scale Ahmed body model was tested in a return-flow automotive wind tunnel.
  • Aerodynamic Measurements: A six-component balance was used to measure drag, and a 96-channel pressure scanner measured surface pressure distribution.
  • Flow Visualization: 2D PIV was used to visualize the flow field around the Ahmed body.
  • Actuator Placement Optimization: The researchers systematically tested two key positions for the upper electrode of the SDBD actuator: on top of the slanted surface (Position 1) and at the trailing edge of the top surface (Position 2).
  • Parameter Studies: The influence of excitation voltage and wind speed on drag reduction was investigated.

Datasets

Not discussed in the paper. The study relies on experimental data collected from wind tunnel tests and quiescent flow measurements.

Key Insights and Ideas

  • Actuator Placement Matters: The location of the SDBD actuator's upper electrode significantly impacts its effectiveness. Placing it at the trailing edge of the top surface (Position 2) proved more effective than on the slanted surface (Position 1) for controlling flow separation. This is attributed to the plasma generation region being closer to the natural separation point.
  • Voltage Optimization is Crucial: There's an optimal excitation voltage for maximum ionic wind velocity. Beyond this point, increasing voltage can lead to plasma saturation and a decrease in induced velocity, diminishing the control effect. For this specific actuator, 17 kV yielded the maximum induced velocity of 3.3 m/s.
  • Drag Reduction Mechanism: The plasma actuator primarily reduces drag by suppressing the separation zone on the slanted surface. This leads to increased pressure in that region, counteracting the low-pressure areas that contribute significantly to drag.
  • Wind Speed Dependency: The effectiveness of the SDBD actuator is highly dependent on wind speed. Significant drag reduction was observed at lower speeds (10-15 m/s), but this effectiveness diminished considerably at higher speeds (20-25 m/s).

Key Results

  • Maximum Ionic Wind Velocity: A maximum induced velocity of 3.3 m/s was achieved at an excitation voltage of 17 kV in quiescent flow.
  • Optimal Actuator Position: Position 2 (upper electrode at the trailing edge of the top surface) showed better control effects than Position 1.
  • Drag Reduction at Low Speeds:
    • At 10 m/s, a maximum drag reduction of 7.92% was achieved with an ionic wind velocity of 1.71 m/s.
  • At 15 m/s, a maximum drag reduction of 7.87% was achieved with an ionic wind velocity of 2.54 m/s.
  • Reduced Drag Reduction at High Speeds:
    • At 20 m/s, drag reduction dropped to 6.20%.
  • At 25 m/s, drag reduction was only 2.91%.
  • Voltage Saturation: The drag reduction effect plateaued at excitation voltages above 11 kV for 10 m/s and above 13 kV for 15 m/s, indicating the actuator's control limit.

Limitations and Future Work

  • High Wind Speed Limitations: The current SDBD actuator design, even at its optimal voltage, does not generate sufficient thrust to achieve substantial drag reduction at high wind speeds.
  • Actuator Optimization: The authors suggest that continued optimization of the actuator design is necessary to generate more thrust for effective control at higher speeds.
  • Multiple Actuators: For further investigation, the use of multiple plasma actuators simultaneously is recommended to achieve better control at higher speeds.
  • Energy Consumption Evaluation: Future work should also evaluate the relationship between the plasma actuator's energy consumption and the resulting fuel reduction.

Summary updated

Abstract

Quiescent flow and wind tunnel tests were performed to gain additional physical insights into flow control for automotive aerodynamics using surface dielectric barrier discharge plasma actuators. First, the aerodynamic characteristics of ionic wind were studied, and a maximum induced velocity of 3.3 m/s was achieved at an excitation voltage of 17 kV. Then, the optimal installation position of the actuator and the influence of the excitation voltage on flow control at different wind speeds were studied. The conclusions drawn are as follows. The effect of flow control is better when the upper electrode of the actuator is placed at the end of the top surface, increasing the likelihood of the plasma generation region approaching the natural separation location. The pressure on top of the slanted surface is primarily affected by airflow acceleration at a low excitation voltage and by the decrease of the separation zone at a high excitation voltage. The maximum drag reduction can be realized when the maximum velocity of ionic wind reaches 1.71 m/s at a wind speed of 10 m/s and 2.54 m/s at a wind speed of 15 m/s. Moreover, effective drag reduction can be achieved only by continuing to optimize the actuator to generate considerable thrust at a high wind speed.
BibTeX
@inproceedings{zheng2019separation,
  author = {Hui Zheng and Xingjun Hu and Peng Guo and Zewei Wang and Jingyu Wang},
  title = {{Separation Flow Control of a Generic Ground Vehicle Using an SDBD Plasma Actuator}},
  booktitle = {Energies},
  year = {2019},
  doi = {10.3390/en12203805},
}
Figure