Abstract
The influences of the endwall corner jet (ECJ) with different locations, yaw angles and jet-to-inflow total pressure ratios on the aerodynamic performance of a high-speed compressor cascade are parametrically investigated by numerical simulation. The results show that the ECJ could weaken the boundary layer separation, reduce the loss and increase the pressure rise effectively by inputting momentum to the low energy corner region. The optimal ECJ location for the loss reduction is slightly downstream of the separation line. With the increase of the yaw angle, more loss reduction is obtained in the near endwall region, whereas the loss near the midspan is enhanced due to the enlarged separation along the blade height. A higher jet-to-inflow total pressure ratio could enhance the pressure rise of the cascade, whereas the mixing losses between the jet and the low energy fluid are also strengthened. The benefit of loss reduction degrades when the jet-to-inflow total pressure ratio is higher than 1.1. Moreover, the ECJ could obtain considerable loss reduction for the incidence ranging from -4° to +4°. A maximum loss reduction up to 15.0% is obtained at the incidence of +2° by the ECJ located at 60% chord with a yaw angle of 30°, whereas the jet-to-inflow mass flow ratio is only 0.57%.
Introduction
In the pursuit of high-performance aero-engines, modern compressor designs utilize "highly loaded" blades to achieve significant pressure rises. However, this design philosophy creates a challenging aerodynamic environment. Low-energy air tends to accumulate in the corners where the blade meets the casing (the endwall), leading to severe flow separation. This separation manifests as turbulent, stagnant regions that significantly increase energy loss, reduce pressure rise, and threaten engine stability.
While various active and passive flow control methods have been proposed, many suffer from manufacturing complexity or a lack of adaptability to varying flight conditions. This paper investigates the Endwall Corner Jet (ECJ) as a practical, high-efficiency alternative for re-energizing the boundary layer and mitigating corner separation.
Methodology and Validation
The researchers conducted a high-fidelity parametric study using numerical simulations to evaluate the ECJ's effectiveness. The study utilized ANSYS CFX to solve the three-dimensional steady viscous Reynolds-Averaged Navier-Stokes (RANS) equations, paired with the SST $k-\omega$ turbulence model, which is widely recognized for its accuracy in predicting flow separation onset.
The study focused on a standardized aerodynamic benchmark: the NACA65-K48 compressor profile. To ensure the virtual model's reliability, the simulation was rigorously validated against experimental data from Hergt et al. (2011). As shown in the comparison of surface streamlines, the simulation accurately captures the secondary flows and the extent of corner separation observed in physical experiments.
Three primary variables were systematically investigated:
- Axial Location: Placement along the blade chord (30% to 80%).
- Yaw Angle ($\alpha$): The injection angle relative to the wall.
- Pressure Ratio: The strength of the jet relative to the incoming flow.
Key Insights and Discussion
Momentum Injection and Optimal Location
The fundamental mechanism of the ECJ is momentum injection. By introducing high-energy air directly into the sluggish corner boundary layer, the jet helps the flow resist the adverse pressure gradients that typically trigger stall. The study identified a "sweet spot" for jet placement at 60% of the chord length, which is slightly downstream of the natural separation line. Placing the jet too far upstream allows its energy to dissipate before reaching the critical separation zone.
The Yaw Angle Trade-off
Adjusting the yaw angle ($\alpha$) presents a balancing act. While increasing the angle effectively clears low-energy air near the endwall, it can inadvertently push the separation higher up the blade toward the midspan. A 30° yaw angle was found to provide the optimal balance between endwall clearance and midspan stability.
Diminishing Returns on Pressure
Interestingly, more pressure does not always equate to better performance. The benefits of loss reduction begin to degrade when the jet-to-inflow total pressure ratio exceeds 1.1. At these higher levels, the "mixing losses"—the turbulence generated when the high-velocity jet interacts with the slower mainstream flow—begin to outweigh the aerodynamic gains from separation control.
Key Results
The ECJ demonstrated remarkable efficiency across a variety of conditions:
- Maximum Performance: A peak loss reduction of 15.0% was achieved at an incidence angle of +2°.
- Design Point: At standard operating conditions, the optimal configuration (60% chord, 30° yaw) reduced total pressure loss by 11.6%.
- Efficiency: These gains were achieved with a minimal jet-to-inflow mass flow ratio of only 0.57%, making it a highly efficient control method.
- Robustness: The ECJ remained effective across a wide incidence range (-4° to +4°), suggesting it is a robust solution for real-world flight envelopes.
Conclusion and Future Work
The Endwall Corner Jet proves to be a potent tool for enhancing compressor performance with minimal mass flow requirements. However, several avenues for future research remain. This study focused on steady jets; investigating pulsed or "unsteady" jets might yield even higher efficiencies. Additionally, while the stationary cascade results are promising, future work must account for the centrifugal and Coriolis forces present in rotating engine components. Finally, the mechanical integration of these jet systems into thin compressor blades remains a significant engineering challenge for the next generation of aero-engines.
Summary updated