Selective Extraction of Bio-oil from Hydrothermal Liquefaction of Salix psammophila by Organic Solvents with Different Polarities through Multistep Extraction Separation

Xiao Yang, Hang Lyu, Kaifei Chen, Xiangdong Zhu, Shicheng Zhang, Jianmin ChenBioResources 2014 · DOI

Abstract: Bio-oil obtained from hydrothermal liquefaction of Salix psammophila is a complex mixture containing numerous high-value chemicals. To facilitate the separation of these components, this study investigated solvent extraction using nine organic solvents with varying polarities. The extraction yields followed the order: tetrahydrofuran (THF) > toluene > ethyl acetate (EAC) > acetone > ether > methylene chloride > methanol > petroleum ether > n-hexane. Utilizing these findings, a multistep extraction process using n-hexane, ethyl acetate, and THF was developed to fractionate the bio-oil into light oil (26.13%), mid-weight oil (54.19%), and heavy oil (19.68%). Characterization via GC-MS, FTIR, NMR, and TGA revealed that high-value chemicals were concentrated in the light oil, while the mid-weight oil showed potential as a petroleum asphalt substitute, and the heavy oil was unexpectedly rich in alkanes.

Introduction

Hydrothermal liquefaction (HTL) is a leading technology for converting wet biomass into liquid bio-oils. However, the resulting crude bio-oil is a dense, complex mixture of hundreds of organic compounds, which complicates its direct application. Traditional separation techniques like distillation often result in coking, while membrane-based methods are prone to fouling. To overcome these challenges, researchers are exploring selective solvent extraction to isolate specific chemical families. This study presents a systematic approach to fractionating bio-oil derived from willow (Salix psammophila) using a sequence of organic solvents tailored to the chemical polarities of the oil's constituents.

Methods and Materials

The investigation began with a screening phase to evaluate the extraction efficiency of nine solvents ranging from non-polar (n-hexane) to highly polar (methanol). Based on the observed yields, a multistep extraction protocol was designed to partition the bio-oil into three distinct fractions.

Figure 5: Flowchart illustrating the multistep extraction sequence used to fractionate bio-crude into heavy, mid-weight, and light oils.

The process utilizes THF for initial extraction from the raw bio-crude, followed by sequential separations using ethyl acetate and n-hexane. The resulting fractions—Light Oil (LO), Mid-weight Oil (MO), and Heavy Oil (HO)—were then characterized using advanced analytical techniques including Gas Chromatography-Mass Spectrometry (GC-MS) and Thermogravimetric Analysis (TGA).

Results and Discussion

The screening results demonstrated that bio-oil extraction yield is not a linear function of solvent polarity. Instead, the yield fluctuates, indicating that the bio-oil contains distinct groups of compounds with specific solvent affinities.

Figure 1: Bio-oil extraction yields for various organic solvents plotted against their polarity index.

THF emerged as the most effective solvent, achieving an extraction yield of approximately 45%. The subsequent multistep fractionation successfully divided the extracted oil into three streams with unique chemical profiles:

  • Light Oil (26.13%): This fraction served as a concentrate for high-value low-molecular-weight chemicals, such as phenols and cyclopentenones, which are critical for the fragrance and polymer industries.
  • Mid-weight Oil (54.19%): Comprising the bulk of the extracted material, this fraction is rich in aromatic oligomers derived from lignin. Its thermal stability and adhesive properties make it a promising candidate for partially replacing petroleum-based asphalt binders.
  • Heavy Oil (19.68%): Surprisingly, this fraction was found to be rich in alkanes. These are hypothesized to be original plant waxes that remained intact throughout the HTL process.

Conclusion

The developed multistep solvent extraction method provides a robust framework for refining complex bio-oils into targeted industrial feedstocks. By isolating high-value chemicals from heavier residues and waxes, this approach enhances the economic viability of biomass liquefaction. Future work will focus on optimizing solvent recovery systems and scaling the process for industrial applications, potentially adapting the solvent sequence for different biomass feedstocks.

Summary updated

Abstract

Bio-oil obtained from hydrothermal liquefaction of Salix psammophila is a very complicated mixture with some highly valued chemicals. In order to separate the chemicals from bio-oil, solvent extraction using nine solvents with different polarities were investigated in detail. The bio-oil extraction yield of the nine solvents were from high to low: tetrahydrofuran > toluene > ethyl acetate > acetone > ether > methylene chloride > methanol > petroleum ether > n-hexane. Based on their extraction yield, an efficient solvent combination of n-hexane, ethyl acetate, and tetrahydrofuran was used to separate the bio-oil through multistep extraction into three parts: light oil (26.13%), mid-weight oil (54.19%), and heavy oil (19.68%). These fractions were characterized by gas chromatography-mass spectrometry, Fourier transform infrared spectroscopy, 1 H nuclear magnetic resonance spectroscopy, and thermogravimetric analysis. The results showed that most of the highly valued chemicals were contained in the light oil; the mid-weight oil consisted of aromatic oligomer derived from the decomposition of lignin, which could be a promising candidate for partial substitute for petroleumasphalt binder; the heavy oil was rich in alkanes
BibTeX
@inproceedings{yang2014selective,
  author = {Xiao Yang and Hang Lyu and Kaifei Chen and Xiangdong Zhu and Shicheng Zhang and Jianmin Chen},
  title = {{Selective Extraction of Bio-oil from Hydrothermal Liquefaction of Salix psammophila by Organic Solvents with Different Polarities through Multistep Extraction Separation}},
  booktitle = {BioResources},
  year = {2014},
  doi = {10.15376/biores.9.3.5219-5233},
}
Figure