Robust interface and reduced operation pressure enabled by co-rolling dry-process for stable all-solid-state batteries

Dong Ju Lee, Yuju Jeon, Jung-Pil Lee, Lanshuang Zhang, Ki Hwan Koh, Feng Li, Anthony U. Mu, Junlin Wu, Yuting Chen, Steven G. McNulty, Wei Tang, Marta Vicencio, Dapeng Xu, Ji Young Kim, Zheng ChenNature Communications 2025 · DOI

TL;DR

Researchers have developed a "co-rolling" dry-process that simultaneously fabricates thin solid-state electrolyte (SSE) layers and high-loading cathodes without using toxic solvents. This integrated approach creates a reinforced, "fused" interface that allows all-solid-state batteries (ASSBs) to maintain high performance even at low operating pressures (2 MPa), a major hurdle for practical EV applications.

What Problem Does This Paper Address?

All-solid-state batteries are the "holy grail" of energy storage due to their high energy density and inherent safety. However, manufacturing them is a nightmare. Current "wet" methods rely on toxic solvents that are environmentally unfriendly and can degrade sensitive electrolyte materials.

While "dry" processing (using binders like PTFE) is more sustainable, it faces a catch-22: to maximize energy density, the SSE layer must be incredibly thin, but thin freestanding SSE films are mechanically fragile and prone to cracking during assembly. Furthermore, most ASSBs require massive "stack pressure" (often >50 MPa) to maintain contact between particles as they expand and contract. This requires heavy, bulky external clamping in a real-world battery pack, defeating the purpose of a high-energy-density cell.

Methods

The authors introduce a co-rolling dry-process. Instead of fabricating a freestanding SSE film and then stacking it onto an electrode, they roll a thick SSE "feed" and a positive electrode "feed" together through a series of rollers.

Key technical nuances include:

  • Binder Fibrillation: They use a tiny amount of PTFE binder (<0.1 wt% in some layers). The shear force from the rollers causes the PTFE to form a web-like network (fibrillation) that holds the particles together.
  • Optimized Parameters: They found that a co-rolling temperature of 120 °C and a gradual reduction in thickness (20 µm steps) were critical to prevent the electrode from piercing the SSE layer.
  • Material Selection: They utilized small, single-crystalline NCM (SC-NCM) particles, which proved more robust against the mechanical stresses of rolling compared to larger polycrystalline particles that tend to crack.

Datasets

As a materials science study, the "datasets" consist of experimental benchmarks and comparative performance metrics:

  • Baseline: Freestanding SSE films and electrodes fabricated via conventional dry-pressing.
  • Characterization: Scanning Electron Microscopy (SEM) for interface analysis, Micro-computed tomography (CT) for 3D structural mapping, and Electrochemical Impedance Spectroscopy (EIS) to measure internal resistance.
  • Performance Benchmarks: Cycling data at varying pressures (2 MPa to 75 MPa) and temperatures (23 °C to 60 °C).

Key Insights and Ideas

  • The "Fused" Interface: The most significant discovery is that co-rolling doesn't just put two layers together; it creates an "intimate" interface. The shear forces induce binder fibrillation across the boundary and force SSE particles into the voids of the electrode. This creates a "network-reinforced" structure that is much tougher than the sum of its parts.
  • Pressure Independence: Because the interface is so well-constructed during fabrication, the battery doesn't rely as heavily on external pressure to keep the components in contact. This is why the cells could cycle 500 times at just 2 MPa—a pressure level manageable in actual electric vehicle packs.
  • Mechanical Synergy: A 50 µm SSE layer is normally too fragile to handle. However, when co-rolled onto a thick electrode, the electrode acts as a mechanical substrate, allowing the total integrated film to achieve a tensile strength of 0.510 N/cm, significantly higher than the individual components.

Key Results

  • Geometry: Achieved a uniform 50 µm SSE layer integrated with a high-loading cathode (5 mAh cm⁻²).
  • Stability: The co-rolled cells maintained >80% capacity retention after 500 cycles at a low stack pressure of 2 MPa. In contrast, conventional freestanding films showed significantly higher capacity loss and interfacial void formation at the same pressure.
  • Energy Density: The team demonstrated a pouch cell (using a Silicon anode) with a stack-level specific energy of 310 Wh kg⁻¹ and an energy density of 805 Wh L⁻¹. These figures are highly competitive with state-of-the-art liquid-electrolyte lithium-ion batteries.

Limitations and Future Work

While the co-rolling process is a major step forward, the authors note a few remaining hurdles:

  • PTFE Stability: PTFE is known to be electrochemically unstable at very low voltages (near the lithium metal potential). While this paper used LTO and Silicon anodes to mitigate this, future work needs to explore alternative binders or protective coatings if pure lithium metal anodes are to be used.
  • Scalability: While roll-to-roll processing is inherently scalable, transitioning from laboratory-scale rollers to industrial-width production lines will require further optimization of heat and pressure uniformity.
  • Chemical Compatibility: The study focused on sulfide-based electrolytes (LPSCl). Testing the co-rolling process with other SSE chemistries (like oxides or halides) would confirm the universality of the approach.

Summary updated

Abstract

The dry-process is a sustainable and promising fabrication method for all-solid-state batteries by eliminating solvents. However, a pragmatic fabrication design for thin and robust solid-state electrolyte (SSE) layers has not been established. Herein, we report a dry-process approach that enhances mechanical stability of SSE layers from film fabrication to cell operation. By co-rolling thick SSE and positive electrode feeds, a uniform, thin SSE layer (50 µm) and a high loading positive electrode layer (5 mAh cm<sup>-2</sup>) with high active material ratio (80 wt%) are simultaneously achieved. This SSE-positive electrode integrated film exhibits enhanced physical properties and cyclability (> 80% retention after 500 cycles) at low stack pressure (2 MPa) compared to the freestanding counterparts, attributed to reinforced and intimate SSE-positive electrode interface constructed during co-rolling process. Additionally, an all-solid-state pouch cell with high stack-level specific energy (310 Wh kg<sup>-1</sup>) and energy density (805 Wh L<sup>-1</sup>) operating at 30 °C and 5 MPa is demonstrated.
BibTeX
@inproceedings{lee2025robust,
  author = {Dong Ju Lee and Yuju Jeon and Jung-Pil Lee and Lanshuang Zhang and Ki Hwan Koh and Feng Li and Anthony U. Mu and Junlin Wu and Yuting Chen and Steven G. McNulty and Wei Tang and Marta Vicencio and Dapeng Xu and Ji Young Kim and Zheng Chen},
  title = {{Robust interface and reduced operation pressure enabled by co-rolling dry-process for stable all-solid-state batteries}},
  booktitle = {Nature Communications},
  year = {2025},
  doi = {10.1038/s41467-025-59363-4},
}

Loading related content...

Figure