Research on the Surface Deformation, Fault Rupture, and Coseismic Geohazard of the 2022 Luding Mw 6.8 Earthquake

Yiling Lu, Yinghui Yang, Li Zeng, Wanfu Xu, Jiawei Song, Xiaoyun Li2023 · DOI

TL;DR

This study investigates the 2022 Luding earthquake using InSAR and POT techniques to map surface deformation and identify coseismic geohazards. The research reveals a left-lateral strike-slip fault rupture and provides a detailed understanding of the geohazard distribution, highlighting the critical role of such methods in disaster assessment.

What Problem Does This Paper Address?

The 2022 Luding earthquake, a significant seismic event in Sichuan Province, China, triggered numerous geohazards, causing substantial damage. Traditional methods for assessing surface deformation and geohazards in such complex, high-altitude terrains are often hindered by logistical challenges, sparse seismic networks, and difficult accessibility. This paper aims to overcome these limitations by employing advanced remote sensing techniques to provide a comprehensive analysis of the earthquake's impact, specifically focusing on:

  • Quantifying Coseismic Surface Deformation: Accurately measuring how the ground moved during and immediately after the earthquake.
  • Inverting the Fault Rupture Model: Understanding the geometry and slip distribution of the fault responsible for the earthquake.
  • Identifying and Characterizing Coseismic Geohazards: Mapping the locations and types of landslides, collapses, and other hazards triggered by the earthquake.
  • Establishing the Relationship: Linking the fault rupture and surface deformation to the distribution and density of geohazards.

Methods

The study leverages two primary remote sensing techniques:

  • Interferometric Synthetic Aperture Radar (InSAR): This technique uses pairs of SAR images to detect subtle changes in the Earth's surface over time. By analyzing the phase difference between two SAR images acquired before and after the earthquake, researchers can measure ground displacement along the satellite's line-of-sight (LOS). The paper utilized Sentinel-1A C-band SAR data and processed it using GAMMA software. Key steps included:
  • Interference Processing: Combining ascending and descending track images to capture deformation from different viewing angles.
  • DEM Removal: Using the SRTM-DEM to remove the topographic phase component.
  • Filtering and Phase Unwrapping: Applying Gaussian filtering to improve signal-to-noise ratio and using the Minimum Cost Flow (MCF) method for phase unwrapping.
  • Orbital Error Correction: Employing a bilinear orbital trend surface to correct for satellite orbital inaccuracies.
  • Fault Model Inversion: Using the derived deformation field and elastic dislocation theory to estimate fault parameters (strike, dip, depth, rake) and slip distribution. A simulated annealing nonlinear constraint algorithm was employed for optimization.
  • Pixel Offset Tracking (POT): This method analyzes the intensity and coherence of SAR images to track the movement of surface features. It is particularly useful for detecting larger displacements where InSAR might suffer from decorrelation. The study employed an intensity tracking approach due to the potential for significant surface deformation. Key aspects included:
  • Normalized Cross-Correlation (NCC): Used to identify corresponding points between pre- and post-earthquake SAR images.
  • Search Window Optimization: An iterative process led to the selection of a 150 pixels × 30 pixels search window to balance accuracy and computational efficiency.
  • Geohazard Identification: POT was used to extract deformation along both LOS and azimuth directions, which were then correlated with topography to identify geohazards.

Datasets

  • Sentinel-1A SAR Images: C-band SAR data acquired by the European Space Agency (ESA) were used for both InSAR and POT analyses. Specific acquisition dates for ascending and descending tracks are provided.
  • SRTM-DEM: The Shuttle Radar Topography Mission Digital Elevation Model (30 m resolution) was used for topographic phase removal in InSAR processing.
  • High-Resolution Optical Remote Sensing Images: Post-earthquake optical images, obtained by the Sichuan Earthquake Administration using UAVs, were used to validate the identified geohazards.
  • Focal Mechanism Solutions: Data from GCMT (Global CMT) and USGS were used to constrain the preliminary fault parameters during the inversion process.

Key Insights and Ideas

  • POT's Efficacy for Large-Scale Hazards: While InSAR struggled to capture the relatively modest coseismic surface deformation due to the earthquake's fault rupture not reaching the surface, POT proved effective in identifying larger-scale geohazards like landslides, which typically involve displacements of meters.
  • Geohazard Distribution Linked to Fault Geometry and Slip: The study found a strong correlation between the distribution of coseismic geohazards and the significant slip segments of the seismogenic fault. Geohazards were more prevalent on the fault's flanks, particularly in the hanging wall zone.
  • Dadu River's Role in Landslides: The concentration of geohazards on the northeastern footwalls of the fault along the Dadu River suggests that reservoir bank slope instability, potentially triggered by the earthquake, played a significant role in landslide formation.
  • LOS vs. Azimuth for Hazard Identification: The study highlights that LOS POT results, which are more sensitive to east-west and vertical deformations, were more effective in identifying geohazards associated with the predominantly north-south fault movement, achieving a higher recognition rate.

Key Results

  • Surface Deformation: Maximum LOS deformation reached approximately 190 mm (ascending track) and 140 mm (descending track).
  • Fault Rupture Model:
    • Optimal fault strike: 169.3°
    • Optimal fault dip: 70°
    • Fault depth: 3–12 km
    • Maximum fault slip: 2.67 m at a depth of 7 km.
  • Estimated moment magnitude: Mw 6.72.
  • Coseismic Geohazards: A total of 245 medium- to large-scale coseismic geohazards were identified. These included:
  • Glacier landslides (5)
    • High mountain rupture geohazards (27)
    • Coastal landslides (124)
  • Verification Rate: Optical remote sensing images validated the identified geohazards with verification rates of 71.2% for ascending tracks and 64.7% for descending tracks.

Limitations and Future Work

  • InSAR Decorrelation: Significant surface deformation in the epicenter area led to InSAR interference decorrelation, limiting the detailed capture of coseismic surface deformation.
  • POT Sensitivity: While effective for larger geohazards, the POT technique exhibited reduced sensitivity to minute geohazard targets due to image resolution and processing limitations.
  • Aftershock Influence: Some geohazards identified in post-earthquake SAR images might have been influenced by aftershock events occurring after the optical image capture.
  • Data Availability: While Sentinel-1A data is publicly available, the optical images were obtained by the Sichuan Earthquake Administration, implying potential access limitations for broader research.
  • Future Work: The paper suggests that further investigation into the relationship between geohazards, deformation, and fault activity is warranted. The study also implies that combining different remote sensing techniques and ground-based data can provide a more robust understanding of earthquake impacts.

Summary updated

BibTeX
@misc{lu2023research,
  author = {Yiling Lu and Yinghui Yang and Li Zeng and Wanfu Xu and Jiawei Song and Xiaoyun Li},
  title = {{Research on the Surface Deformation, Fault Rupture, and Coseismic Geohazard of the 2022 Luding Mw 6.8 Earthquake}},
  year = {2023},
  doi = {10.3390/s23249875},
}
Figure