Research on Dynamic Test of Hyper-Velocity Impact Penetration Acceleration Signal

Debiao Zhang, Jie Li, Xiaokai Wei, Kaiqiang Feng, Yu Wang, Jihe Zhao, Dong XueIEEE Access 2020 · DOI

Introduction

As modern ballistics and defense technologies advance into the hyper-velocity regime—speeds exceeding 3,000 m/s—traditional solid-mechanics models for projectiles become insufficient. At these extreme velocities, the impact pressure far exceeds the material strength of both the projectile and the target. Consequently, projectiles undergo significant "mass erosion" and behave more like hydrodynamic jets than rigid solids. Understanding these dynamics requires precise measurement of the penetration acceleration signal, commonly referred to as the "overload."

The Measurement Challenge

Capturing the overload signal is an immense engineering challenge due to the extreme physical conditions of the impact. The signal typically lasts only microseconds, yet it exhibits a catastrophic drop in acceleration—often reaching hundreds of thousands of gs in a fraction of a microsecond. This requires measurement systems with exceptionally high bandwidth and sampling rates.

Simulated penetration acceleration signal showing the extreme deceleration gradient at impact.

Beyond the physical intensity, two primary noise sources plague measurements:

  1. Mechanical Vibrations: The internal movement and structural ringing of the test unit within the projectile.
  2. Electrical Noise: High-frequency noise originating from the Power Delivery Network (PDN) of the circuit board, which can swamp the actual data at microsecond scales.

Methodology

The researchers developed a comprehensive approach combining mechanical modeling, hardware optimization, and advanced signal processing to extract clean data from chaotic impact environments.

Mechanical and Hydrodynamic Modeling

To understand the sensor's response, the researchers modeled the mechanical coupling between the accelerometer and the projectile body using a spring-mass-damper framework. This analysis determined that a sampling rate of at least 200 MHz is necessary to accurately capture the signal's steep falling edge.

Schematic of the projectile-accelerometer system used for mechanical coupling analysis.

For the impact itself, the team utilized the Alekseevskii-Tate model. This hydrodynamic model simulates how a rod-shaped projectile erodes and decelerates, accounting for the "semi-fluid" state of the contact point during hyper-velocity penetration.

Hardware and PDN Analysis

A unique contribution of this research is the focus on the Power Delivery Network (PDN). Unlike standard designs that treat power supplies as ideal constants, this study used S-parameters to model the dynamic impedance of the PCB power planes. By optimizing the PDN, the researchers minimized electrical noise that typically interferes with high-speed data acquisition.

Advanced Signal Processing (MEEMD)

To isolate the true penetration pulse from structural noise, the team introduced Modified Ensemble Empirical Mode Decomposition (MEEMD). This algorithm decomposes complex, non-stationary signals into simpler Intrinsic Mode Functions (IMFs). To distinguish between signal and noise components, they employed Reverse Dispersion Entropy (RDE), optimized via a genetic algorithm, to automatically select the most relevant IMFs.

Results and Discussion

The proposed system was validated using a Hopkinson rod test setup, with a laser interferometer providing the ground truth standard. The results demonstrated high fidelity:

  • Peak Value Error: 3.29%
  • Pulse Width Error: 3.81%

While traditional digital filters like the Butterworth filter often fail to handle the "mutational" nature of impact signals, the MEEMD approach successfully preserved the sharpness of the impact pulse while effectively removing high-frequency structural ringing. However, the authors noted that the MEEMD algorithm is computationally intensive, making it currently unsuitable for real-time processing.

Conclusion

This research provides a robust framework for measuring acceleration in hyper-velocity environments. By addressing both the mechanical coupling of the sensor and the electrical integrity of the power network, the authors achieved high-precision data capture in one of the most demanding regimes of experimental physics. Future work will focus on reducing the computational cost of the noise-reduction algorithms and accounting for electromagnetic crosstalk between signal traces on the measurement hardware.

Summary updated

BibTeX
@article{zhang2020research,
  author = {Debiao Zhang and Jie Li and Xiaokai Wei and Kaiqiang Feng and Yu Wang and Jihe Zhao and Dong Xue},
  title = {{Research on Dynamic Test of Hyper-Velocity Impact Penetration Acceleration Signal}},
  journal = {IEEE Access},
  year = {2020},
  doi = {10.1109/access.2020.3033676},
}
Figure