Research of Tire Pressure Monitoring System

Xu Yuan2016 · DOI

Abstract

Nowadays, the car has become an important means of transportation, and car safety has been paid more and more attention. Abnormal operation can lead to flat tires; therefore, Tire Pressure Monitoring Systems (TPMS) are essential for timely monitoring. This paper provides a comprehensive classification of TPMS based on sensor types, monitoring methods, and principles. It establishes mathematical models for different TPMS architectures, providing a definition of structures that facilitates the analysis and design of future safety systems.

Introduction

Tire failure is a leading cause of highway accidents, with punctures accounting for an estimated 30% to 40% of incidents. Beyond catastrophic failure, improper tire pressure significantly impacts vehicle performance: high pressure reduces traction and causes skidding, while low pressure increases fuel consumption and leads to dangerous heat buildup. Despite the importance of monitoring, there is a wide variety of implementation strategies. This research addresses the need for a clear taxonomy and mathematical foundation for these systems, helping engineers understand the trade-offs between cost, complexity, and accuracy.

Classification and Methodology

The paper categorizes TPMS into two primary architectures: Indirect and Direct systems.

1. Indirect TPMS (WSB TPMS)

Indirect systems do not measure pressure directly. Instead, they infer it using existing vehicle sensors, such as those used for Anti-lock Braking Systems (ABS). The paper explores three main methods:

  • Frequency Analysis: This method treats the tire as a spring. Since there is a linear relationship between a tire's elasticity and its internal pressure, the system uses Vibration Signal Control (VSC) to monitor torsional vibration frequencies. The relationship is governed by the formula $f = 2\pi \sqrt{m/k}$, where $k$ is the elasticity coefficient.
  • Speed Analysis: This relies on the fact that a tire with lower pressure has a smaller rolling radius, causing it to spin faster than others. The system calculates a ratio ($\gamma$) to compare angular velocities across all four wheels to detect discrepancies.
  • Magnetic Detection: This approach uses a pressure sensor on the rim and a Hall effect sensor on the suspension to detect changes in magnetic field direction as pressure fluctuates, utilizing the principle $V_H = K \times B$.
Vibration Signal Control (VSC) logic for indirect tire pressure monitoring.

2. Direct TPMS (PSB TPMS)

Direct systems use dedicated sensors installed inside each tire to provide real-time data. These are further divided into:

  • Active Systems: These utilize battery-powered modules that transmit pressure and temperature data via wireless radio frequency (RF) modulation to a central receiver. These modules must be robust enough to survive "dynamic loads" of 20g and temperature swings from -40°C to +125°C.
  • Passive Systems: These are battery-less designs powered by RFID technology or mechanical energy harvesting, eliminating the maintenance burden and environmental impact of lithium batteries.
Hardware architecture of an active direct TPMS sensor module.

Key Insights and Comparative Analysis

A major insight from this research is the "blind spot" of Speed Analysis. Because it relies on comparing wheels against one another, it often fails to detect a "flat-all-around" scenario where all four tires lose pressure simultaneously, or when two tires on the same side or axle drop at the same rate.

While Direct TPMS is functionally superior—providing actual PSI and temperature readings—it faces significant environmental challenges. Components inside the tire must withstand extreme heat and high centrifugal forces. Conversely, Indirect systems are highly cost-effective because they leverage existing ABS hardware, but they suffer from lower accuracy and specific failure modes like the coaxial pressure drop.

Conclusion and Future Work

The paper serves as a technical roadmap for TPMS design. While current active direct systems provide high precision, they are hampered by the finite life of lithium batteries and the added weight to the wheel assembly.

Future research is directed toward Passive TPMS. Specifically, exploring energy harvesting from the mechanical motion of the car or using RFID read heads to power sensors remotely could remove the battery bottleneck entirely, leading to more sustainable and maintenance-free automotive safety components.

Summary updated

Abstract

Nowadays, the car has become an important means of transportation, the safety of the car has been paid more and more attention by people. The abnormal running will lead to flat tire, TPMS system for the timely monitoring of tire pressure, application of different types of TPMS system are different from each other. Based on the sensor types, monitoring methods and monitoring principle of TPMS system for the classification and different mathematical models are given for different TPMS systems. A more comprehensive definition of the structure of all types of TPMS, which will facilitate analysis and design of TPMS.
BibTeX
@misc{yuan2016research,
  author = {Xu Yuan},
  title = {{Research of Tire Pressure Monitoring System}},
  year = {2016},
  doi = {10.2991/wartia-16.2016.157},
}
Figure