Research and Implementation of the Temperature Control System for the Sintering Shaft Furnace

Guohuan Lou, Jianmin Wang, Jiawei Wang, Fuxing YuInternational Journal of Intelligent Engineering and Systems 2010 · DOI

Abstract

This paper describes the implementation of the temperature control system for sintering shaft furnace. In order to solve the problems caused by pure time-delay and non-linearity, an intelligent serial temperature control system is introduced in this paper, where the fuzzy controller is used in the main control loop and the fuzzy neural network PID controller is adopted in auxiliary loop. Simulation results show that this system is stable and has stronger anti-interference capability. Finally, the hardware and software implementation methods for the firebox temperature control system are introduced. The real production results demonstrate that production requirements are met and better control effects are obtained. The aim of energy saving and consumption reduction and quality improvement is achieved.

Problem Statement: The Complexity of Furnace Temperature Control

Sintering shaft furnaces are critical for roasting pellets used in iron smelting. However, the process is a significant control challenge due to complex thermo-chemical reactions, high non-linearity, and "pure time-delay"—where changes in inputs take a substantial amount of time to reflect in the output temperature.

Schematic diagram of the sintering shaft furnace structure.

Traditional systems typically rely on standard PID (Proportional-Integral-Derivative) control. While reliable in steady states, PID struggles when the quality or pressure of the fuel (blast furnace gas) fluctuates. Most existing systems stabilize temperature by simply adjusting total gas flow, which is inefficient, leads to energy waste, and can disrupt the "oxidation atmosphere" required for high-quality pellets.

Methodology: Intelligent Serial Temperature Control

The authors propose a Serial Temperature Control System designed to maintain stable temperatures without increasing total gas consumption, primarily by optimizing the air-to-gas ratio. The system consists of a main loop and two auxiliary loops.

Main Control Loop: Fuzzy Logic Strategy

Instead of relying on a rigid mathematical model, the main loop utilizes a Fuzzy Controller. It processes the temperature error and the rate of temperature change to output a suggested adjustment to the air/gas ratio ($K$). This approach mimics human expert intuition, effectively handling the furnace's non-linear behavior.

Auxiliary Control Loops: Fuzzy Neural Network PID

Two auxiliary loops—one for gas flow and one for air flow—employ a Fuzzy Neural Network (FNN) PID controller.

Structure of the Fuzzy Neural Network PID controller.

The FNN-PID architecture consists of a five-layer neural network that learns and updates weight coefficients online. Rather than generating a direct control signal, the network's output defines the optimal parameters ($K_p, K_i, K_d$) for a standard PID controller. This hybrid approach allows the system to adapt its responsiveness in real-time based on current flow conditions.

Experimental Results and Industrial Implementation

The system was validated through MATLAB simulations and real-world deployment at the Xingtai Iron and Steel Company in China, utilizing a Logix5000 PLC and RSView32 HMI stack.

Key Performance Metrics:

  • Response Time: In simulations, the FNN-PID reached the target temperature in 320 seconds with zero overshoot. In contrast, standard PID took 500 seconds (15.2% overshoot) and standard Fuzzy PID took 810 seconds (10.4% overshoot).
  • Anti-Interference: The system demonstrated high robustness, recovering and stabilizing within 60 seconds after an $80^\circ C$ interference signal was introduced.
  • Industrial Impact:
    • Energy Efficiency: Total energy consumption was reduced by 3.8%.
  • Product Quality: The pellet qualification rate increased by 6.4%.
  • Operational Stability: Firebox temperature was maintained within a tight window of $\pm 10^\circ C$.

Conclusion

The decoupling strategy—keeping total gas volume fixed while treating the air/gas ratio as the primary control variable—ensures the furnace maintains the necessary "oxygenation atmosphere" for pellet chemistry while preventing energy waste. By combining Fuzzy Logic for high-level strategy and Neural Networks for tactical parameter tuning, the system achieves a balance of robustness and precision. Future work may involve porting this logic to modern IoT frameworks and integrating remote monitoring to further reduce labor intensity.

Summary updated

Abstract

This paper describes the implementation of the temperature control system for sintering shaft furnace. In order to solve the problems caused by pure time-delay and non-linearity, an intelligent serial temperature control system is introduced in this paper, where the fuzzy controller is used in the main control loop and the fuzzy neural network PID controller is adopted in auxiliary loop. Simulation results show that this system is stable and has stronger anti-interference capability. Finally, the hardware and software implementation methods for the firebox temperature control system are introduced. The real production results demonstrate that production requirements are met and better control effects are obtained. The aim of energy saving and consumption reduction and quality improvement is achieved.
BibTeX
@article{lou2010research,
  author = {Guohuan Lou and Jianmin Wang and Jiawei Wang and Fuxing Yu},
  title = {{Research and Implementation of the Temperature Control System for the Sintering Shaft Furnace}},
  journal = {International Journal of Intelligent Engineering and Systems},
  year = {2010},
  doi = {10.22266/ijies2010.0331.02},
}
Figure