Regeneration of industrial cutting blades made from X39Cr13 steel used in skinning process of Pleuronectidae-family flatfishes

Bartosz Zieliński, Wojciech Kapłonek, Krzysztof NadolnyJournal of Mechanical and Energy Engineering 2018 · DOI

Abstract

In the fish processing industry, the intensive wear of cutting surfaces on industrial blades is a significant economic and technical challenge. This paper presents a proprietary solution for the regeneration of worn blades using a prototype 5-axis CNC grinding machine. The process focuses on restoring the complex two-phase geometry of blades made from X39Cr13 steel. Results were validated through cutting edge inclination angle measurements and surface roughness analysis, demonstrating that CNC-based regeneration is a viable alternative to tool replacement.

Introduction

The skinning of flatfishes (Pleuronectidae family) requires high-precision industrial blades that operate in demanding environments. These tools are subjected to mechanical wear from fish raw material, corrosive saltwater, and aggressive chemical cleaning agents like nitric and phosphoric acids. When the cutting edge dulls or loses its specific geometry, it leads to "tearing" of the fish meat and significant production losses. Traditionally, the industry has favored replacing these expensive martensitic stainless steel blades. This research explores a more sustainable "regeneration" approach using advanced CNC grinding.

Methodology

The core of the proposed solution is a prototype 5-axis CNC grinding machine designed to handle the low stiffness and complex geometry of skinning blades. The machine utilizes a high-speed electrospindle (30,000–36,000 RPM) and a cubic Boron Nitride (cBN) grinding wheel with a ceramic binder.

Detail of the mechanical assembly and adjustment components of the prototype CNC grinding machine.

The regeneration process aims to restore a "two-phase" cutting edge geometry:

  1. Phase 1 ($\alpha_1$): The primary edge angle, nominally ~28°.
  2. Phase 2 ($\alpha_2$): The secondary chamfer angle, nominally ~33°.
The industrial control interface and power supply (3x400V) for the prototype 5-axis CNC machine.

Verification was performed using stylus profilometry (Hommel-Tester T8000) to measure inclination angles and surface roughness parameters ($Ra, Rq, Rt, Rz$) across six blades: two new reference blades and four worn blades processed through the prototype machine.

Results and Discussion

The CNC regeneration successfully restored the functional geometry of the blades, though some deviations from the factory-new reference were observed.

  • Geometric Accuracy: While the nominal angles were 28°43’ and 33°55’, the regenerated blades achieved angles between 30°11’–30°50’ for Phase 1 and 34°22’–41°30’ for Phase 2.
  • Surface Quality: The regenerated surfaces exhibited higher roughness than the reference blades. The arithmetical mean deviation ($Ra$) was approximately 39% higher for Phase 1 and 61% higher for Phase 2.

Despite these deviations, the blades were restored to a functional state capable of performing the skinning process without damaging the raw material. The increased roughness and angular shifts are attributed to the prototype machine's stiffness and the initial grinding parameters.

Conclusion

This study demonstrates that a 5-axis CNC grinding process can effectively regenerate specialized industrial cutting tools. While the prototype results show room for optimization in terms of surface finish and angular precision, the method provides a clear path toward reducing waste and operational costs in the food processing industry. Future work will focus on optimizing feed speeds and improving the structural rigidity of the grinding machine to match factory-level specifications.

Summary updated

Abstract

One of the important and still current problems occurring in the fish processing industry is the intensive wear of the cutting surface of industrial cutting blades used to separate the fish raw material. In the paper, the proposes a proprietary solution to the above problem consisting in the regeneration of worn surfaces realized in the process of precise grinding by the use of a prototype 5-axis CNC grinding machine was presented. The obtained machining results were verified, among others on the basis of measurements of values of the cutting edges inclination angles and analysis of values of selected surface roughness parameters. The proposed solution along with the developed methodology can be an interesting alternative to typical ways of renewing the cutting ability of cutting tools in applications from the fish processing industry.
BibTeX
@article{zielinski2018regeneration,
  author = {Bartosz Zieliński and Wojciech Kapłonek and Krzysztof Nadolny},
  title = {{Regeneration of industrial cutting blades made from X39Cr13 steel used in skinning process of Pleuronectidae-family flatfishes}},
  journal = {Journal of Mechanical and Energy Engineering},
  year = {2018},
  doi = {10.30464/jmee.2018.2.4.277},
}
Figure