Reduction Effect of Extra Biochar on PAHs Originating from Corn Stover Pyrolysis

Lijie Li, Xiuli Shen, Meng HaiBo, Yujun Shen, Jingtao Ding, Hongbin Cong, Mingsong ChenMolecules 2025 · DOI

TL;DR

This study explores using pre-made biochar as a catalyst to reduce harmful polycyclic aromatic hydrocarbons (PAHs) during corn stover pyrolysis. While adding extra biochar significantly lowered PAHs in the resulting solid biochar, especially at lower temperatures, it paradoxically increased PAHs in the residual tar at higher temperatures, indicating a complex, temperature-dependent catalytic effect.

What Problem Does This Paper Address?

Biochar, a promising material for soil improvement and carbon sequestration, can contain concerning levels of polycyclic aromatic hydrocarbons (PAHs). These PAHs are toxic and pose environmental and health risks, making their reduction during biochar production crucial for widespread adoption. Current methods for minimizing PAHs are often complex or energy-intensive. This paper investigates a simpler, potentially more cost-effective approach: using pre-produced biochar as a "catalyst" to mitigate PAH formation during the pyrolysis of corn stover, a common agricultural residue. The goal is to develop a more sustainable and safer biochar production process.

Methods

The researchers employed a fixed-bed pyrolysis reactor to process corn stover at three different temperatures: 500, 600, and 700 °C. The core experimental design involved "stacking" extra biochar (prepared separately from corn stover at the same temperatures) on top of the raw corn stover in the reactor. This setup aimed to allow pyrolysis vapors to interact with the extra biochar catalyst as they evolved.

After pyrolysis, the researchers analyzed the resulting biochar and the "residual tar" (a semi-solid tar trapped within the reactor) for the concentration of 16 US EPA-listed PAHs using gas chromatography-mass spectrometry (GC-MS). They also characterized the extra biochar catalysts themselves using:

  • Scanning Electron Microscopy (SEM): To visualize surface morphology and pore structure.
  • Brunauer-Emmett-Teller (BET) analysis: To determine specific surface area and pore size distribution.
  • Raman Spectroscopy: To analyze the carbon structure and functional groups.
  • X-ray Photoelectron Spectroscopy (XPS): To investigate surface elemental composition and chemical states of carbon and oxygen.

Datasets

Not discussed in the paper. The study utilizes corn stover as the feedstock and pre-prepared biochar as the catalyst. The primary "data" generated are the PAH concentrations in the biochar and residual tar, and the characterization data of the biochar catalysts.

Key Insights and Ideas

  • Dual Role of Extra Biochar: The extra biochar acts not just as a passive material but as a catalytic surface. It appears to adsorb and react with pyrolysis vapors, influencing the final PAH content.
  • Temperature-Dependent Effects: The catalytic effect of the extra biochar is highly dependent on temperature. It's beneficial at lower temperatures (500 °C) for reducing PAHs in the biochar product but can exacerbate PAH formation in the residual tar at higher temperatures (600-700 °C).
  • PAH Source Shift: The study suggests that in the presence of extra biochar, the primary pathway for PAH formation in the biochar shifts away from secondary gas-phase reactions and towards solid-phase mechanisms, which are then suppressed.
  • Tar as a PAH Reservoir: The residual tar, often overlooked, is a significant reservoir of PAHs, and its behavior is crucial to understanding the overall PAH reduction strategy. The increase in tar-bound PAHs at higher temperatures is a major concern.
  • Catalyst Modification: The characterization techniques (SEM, BET, Raman, XPS) reveal that the extra biochar undergoes structural and chemical changes during the process, indicating its active role in the catalytic cycle.

Key Results

  • Biochar PAH Reduction: At 500 °C, adding extra biochar reduced PAHs in the resulting corn stover biochar by a significant 82.52% (from ~9.14 mg/kg to ~1.25 mg/kg). Even at higher temperatures, biochar-bound PAHs decreased by 59.96–74.14%.
  • Residual Tar PAH Increase: Conversely, at 600 °C and 700 °C, the concentration of PAHs in the residual tar increased substantially (up to 4.51–5.85 times higher than the blank groups).
  • Toxicity Equivalent (TEQ): The TEQ of biochar was significantly reduced by the extra biochar, falling from 0.05–0.23 mg/kg to almost zero at 500 °C. However, the TEQ of the residual tar remained high and increased with temperature.
  • Correlation Analysis: A significant positive correlation between PAHs in biochar and residual tar was observed in the absence of extra biochar, suggesting residual tar is a source. With extra biochar at 500-600 °C, this correlation disappeared, indicating an inhibitory effect. However, at 700 °C, the correlation reappeared, suggesting a different mechanism at play.

Limitations and Future Work

  • Incomplete Elimination: The study concludes that while adding extra biochar effectively reduces PAHs in the biochar product, it does not completely eliminate PAH issues in the entire pyrolysis process, particularly concerning the residual tar.
  • Temperature Dependence: The paradoxical increase in residual tar PAHs at higher temperatures highlights the need for further investigation into the specific catalytic pathways and how to manage them.
  • Reactor Design: The authors emphasize the need for targeted reactor modifications to address tar accumulation, suggesting this is a critical area for future work.
  • Economic Viability: While the approach is presented as potentially more economical, a full life-cycle assessment and energy input analysis would be beneficial.
  • Future Research: The authors suggest focusing on reactor-level tar mitigation techniques and conducting a comprehensive life-cycle assessment of this biochar-catalyzed pyrolysis method.

Summary updated

Abstract

As attention to environmental risks from the PAHs in biochar production increases, developing a low-cost and easy-to-operate optimized pyrolysis process is urgent. The effect of extra biochar was investigated in order to minimize polycyclic aromatic hydrocarbons (PAHs) on biochar and residual tar for the development of a new fixed-bed pyrolysis process. Hence, the effect of extra biochar as a catalyst on the reduction effect on PAHs originating from corn stover pyrolysis was inspected and explored in this study. Pyrolysis was conducted at 500, 600, and 700 °C in a tube furnace reactor with corn stover as the biomass feedstock. Biochar prepared at 500 °C, 600 °C, and 700 °C was used as a catalyst by stacking extra biochar on top of the corn stover raw material. Then, the concentration of PAHs in corn stover biochar and residual tar inside the reactor was examined. The physicochemical characteristics, including morphology, pore structure, and chemical structures of extra biochar, were investigated separately. The results showed that, with stacking extra biochar, the concentrations of PAHs in corn stover biochar (7.15 mg/kg to 1.25 mg/kg) and residual tar (132.23 mg/kg to 101.10 mg/kg) inside the reactor decreased significantly at medium temperatures (500 °C). The concentrations of PAHs in corn stover biochar decreased from 9.14 mg/kg, 10.44 mg/kg to 3.66 mg/kg, 2.7 mg/kg. However, the concentrations of PAHs of residual tar inside the reactor increased significantly at medium temperatures (600 °C, 700 °C). In addition, the reaction mechanism of extra biochar as a catalyst to reduce PAHs in corn stover biochar was established. The results suggest that the measure of adding extra biochar reduced PAHs in resulting biochar effectively, but is not high enough to eliminate PAHs issues in the entire pyrolysis process completely.
BibTeX
@inproceedings{li2025reduction,
  author = {Lijie Li and Xiuli Shen and Meng HaiBo and Yujun Shen and Jingtao Ding and Hongbin Cong and Mingsong Chen},
  title = {{Reduction Effect of Extra Biochar on PAHs Originating from Corn Stover Pyrolysis}},
  booktitle = {Molecules},
  year = {2025},
  doi = {10.3390/molecules30214238},
}
Figure