Real-Time Response-Based Fault Analysis and Prognostics Techniques of Nonisolated DC-DC Converters

Zhen Jia, Zhenbao Liu, Chi-Man Vong, Xin LiuIEEE Access 2019 · OpenReview

Abstract

DC-DC converters are critical components in industrial systems, where their failure can lead to abnormal operation or catastrophic accidents. Traditional fault analysis often relies on complex mathematical modeling or invasive signal processing. This paper proposes a non-invasive fault analysis method based solely on the circuit's output voltage response. By monitoring the output signal, the system can simultaneously locate faulty components and predict their Remaining Useful Performance (RUP). To address the common issue of particle degeneracy in standard prognostic algorithms, a novel conditional particle filter (CPF) is introduced. This filter utilizes historical degradation data to maintain particle diversity and improve prediction accuracy. Case studies on two converter topologies demonstrate that the proposed method effectively identifies fault conditions and achieves high RUP prediction precision.

Introduction

DC-DC converters are essential for power management in industrial electronics but are highly susceptible to environmental stressors such as heat, vibration, and aging. When internal components like capacitors or inductors drift from their nominal values, system stability is compromised.

Current diagnostic approaches generally fall into two categories: model-based methods, which are computationally intensive and struggle with real-world non-linearities, and signal-processing methods, which often require internal node access. Probing internal nodes is frequently impractical for sealed or high-density industrial units. Furthermore, standard prognostic tools like Particle Filters (PF) often suffer from "particle degeneracy," where the statistical diversity of future state guesses collapses, leading to inaccurate failure forecasts. This research introduces a "black-box" diagnostic approach that identifies internal component degradation using only the output voltage wire.

Methodology

The proposed system employs a two-stage strategy for health monitoring: output-based fault analysis and RUP prediction via an improved particle filter.

Output-Based Fault Analysis

Instead of monitoring internal nodes, the system focuses on the Output Average Voltage ($V_{oa}$). The researchers pre-construct "fault-indicating curves" by simulating how specific sensitive components (e.g., filter inductors or feedback resistors) affect the output voltage as they deviate from nominal values. By matching real-time $V_{oa}$ readings against these stored signatures, the system can pinpoint the specific component undergoing degradation.

Flowchart of the proposed fault analysis and failure prognostics methodology.

Exemplar-Based Conditional Particle Filter (CPF)

To predict RUP, the authors developed a Conditional Particle Filter that incorporates historical degradation data as "exemplars." Unlike standard PFs, which can lose diversity during the resampling step, the CPF uses historical failure trajectories to guide current predictions. This ensures that the statistical "particles" remain grounded in realistic failure patterns, significantly mitigating the degeneracy problem.

Experimental Setup and Datasets

The methodology was validated using a combination of software simulation and hardware testbeds.

  1. Simulation: Saber software was used to generate SPICE models for two converter types, allowing for the creation of comprehensive fault-indicating curves.
  2. Hardware Testbeds: Two physical circuits were constructed: a simple converter based on the MC34063a chip and a more complex PWM-controlled converter using the TL494 chip.
  3. Data Acquisition: National Instruments boards and LabVIEW were utilized to record real-time voltage data as component degradation was induced.
Schematic of a typical DC-DC converter circuit highlighting the sensitive components (L, C, R) monitored for degradation.

Key Insights and Results

The core finding of this research is that internal component drifts create unique, identifiable "fingerprints" in the output voltage. By focusing on sensitive components identified through theoretical screening (such as L, C, and feedback resistors), the system avoids monitoring components with negligible impact on output health.

  • Diagnostic Accuracy: The system successfully categorized faults (e.g., "Inductor L decrease" or "Resistor R1 increase") across both simple and complex topologies.
  • Prognostic Precision: The CPF demonstrated remarkable accuracy in predicting the End of Performance (EOP). For instance, when monitoring the timing capacitor of the MC34063a, the maximum prediction error was limited to only 4 cycles.
  • Real-Time Feasibility: Because the method relies on output sampling rather than complex internal modeling during operation, it is computationally efficient enough for real-time industrial deployment.

Conclusion

This research provides a robust framework for the real-time health monitoring of DC-DC converters without the need for invasive probing. While the current model focuses on single-component faults with a 20% deviation threshold, future work will explore simultaneous multi-component failures and the impact of extreme environmental noise on diagnostic sensitivity. The integration of historical data into the particle filtering process represents a significant step forward in improving the reliability of power electronic prognostics.

Summary updated

Abstract

DC-dc converters have been extensively used in industrial systems and their failure may cause the systems to work abnormally and even accidents. Current research on circuit fault analysis is mainly based on a model or complex signal processing. In order to avoid modeling difficulties and complex selection of signal processing methods, a fault analysis method based on circuit output signal is proposed in this paper, which can judge the circuit health status by directly monitoring the circuit response. This method of monitoring output signal also avoids the problem of inconvenient access to internal nodes of the converter circuit. By continuously monitoring the output voltage, two advantages are simultaneously achieved: 1) the fault components range of an abnormal circuit is located and 2) its remaining useful performance (RUP) can be predicted. The particle filter algorithm commonly used to predict RUP often encounters the problem of particle degeneracy, which leads to the decrease of particle diversity and makes the final RUP prediction accuracy lower. In view of this problem, the developed novel way of RUP prediction by monitoring the circuit output voltage is based on a newly developed conditional particle filter, which tracks the degradation process of the circuit according to collected historical degeneration data. The case studies of two dc-dc converter circuits show that the developed fault analysis method can easily analyze the fault condition of the converter circuits and the improved particle filter algorithm achieves excellent prediction accuracy.
BibTeX
@inproceedings{jia2019real,
  author = {Zhen Jia and Zhenbao Liu and Chi-Man Vong and Xin Liu},
  title = {{Real-Time Response-Based Fault Analysis and Prognostics Techniques of Nonisolated DC-DC Converters}},
  booktitle = {IEEE Access},
  year = {2019},
  url = {https://openreview.net/forum?id=xh8zkj6tR7},
}
Figure