Reactive-Sputtered Prepared Tin Oxide Thin Film as an Electron Transport Layer for Planar Perovskite Solar Cells

Wenhai Sun, Shuo Wang, Shina Li, Miao Xu, Yu Zhu, Du Chen, Ruixin Ma, Chengyan WangCoatings 2019 · DOI

TL;DR

This paper presents a new, low-temperature method for preparing tin oxide (SnO2) thin films using reactive radio-frequency magnetron sputtering. These SnO2 films serve as effective electron transport layers (ETLs) in perovskite solar cells (PSCs), leading to improved device efficiency and suppressed carrier recombination. The optimized process achieved a maximum power conversion efficiency of 14.63%.

What Problem Does This Paper Address?

Perovskite solar cells (PSCs) have seen rapid efficiency gains, but their performance is heavily reliant on the electron transport layer (ETL). Traditional ETLs like titanium dioxide (TiO2) often require high processing temperatures, which increases manufacturing costs and can limit scalability. While other materials are being explored, there's a need for ETLs that are efficient, stable, and can be fabricated using cost-effective, low-temperature methods suitable for industrial production. This paper addresses the challenge of finding and optimizing such an ETL, focusing on tin oxide (SnO2) as a promising candidate.

Methods

The core of this research is the preparation of SnO2 thin films using radio frequency (RF) reactive magnetron sputtering at room temperature. This technique involves sputtering a pure tin (Sn) target in a reactive atmosphere containing argon (Ar) and oxygen (O2). The process parameters, particularly the sputtering time, were varied to control the film thickness and its properties.

The prepared SnO2 films were then characterized using:

  • UV-Vis spectroscopy to measure transmittance and determine the band gap.
  • X-ray photoelectron spectroscopy (XPS) to analyze elemental composition and chemical states.
  • Atomic Force Microscopy (AFM) and Field-Emission Scanning Electron Microscopy (FESEM) to assess surface morphology and roughness.
  • Ultraviolet Photoelectron Spectroscopy (UPS) to determine energy levels (conduction band, valence band, and Fermi level).

These SnO2 films were integrated as ETLs into planar perovskite solar cells. The performance of these devices was evaluated by measuring their current-voltage (J-V) characteristics under simulated sunlight, external quantum efficiency (EQE), and photoluminescence (PL) spectra to understand carrier recombination.

Datasets

Not discussed in the paper. The study focuses on the fabrication and characterization of the SnO2 films and their integration into perovskite solar cells, rather than training on or evaluating against large datasets.

Key Insights and Ideas

  • Room-temperature sputtering is viable for SnO2 ETLs: The study demonstrates that RF reactive magnetron sputtering can effectively produce high-quality SnO2 films at room temperature, bypassing the need for high-temperature annealing required by some other methods. This is crucial for cost-effective and scalable manufacturing.
  • SnO2 improves interface morphology: The sputtered SnO2 layer reduces the surface roughness of the FTO substrate. This smoother interface leads to better crystallization of the perovskite layer, resulting in a more uniform film with fewer defects.
  • SnO2 effectively suppresses carrier recombination: PL spectra show a significant reduction in recombination when SnO2 is used as an ETL compared to bare FTO. This is a key factor in improving device efficiency.
  • Sputtering time is critical: The research highlights that the sputtering time (and thus film thickness) has a significant impact on device performance. An optimal time of 20 minutes was identified, balancing good coverage and electron transport without introducing excessive resistance.
  • SnO2 offers suitable electronic properties: The determined energy levels of the SnO2 film align well with the perovskite layer, facilitating efficient electron extraction and hole blocking, which are essential for high-performance PSCs.

Key Results

  • High transmittance: The sputtered SnO2 films exhibit high transmittance in the visible region.
  • Optimal band gap: The SnO2 film has a band gap of 3.79 eV.
  • Reduced surface roughness: The roughness of the FTO substrate decreased from 31.8 nm to 30.2 nm after SnO2 sputtering.
  • Improved perovskite morphology: Perovskite films deposited on SnO2 showed a flatter surface and more uniform grain size compared to those on bare FTO.
  • Suppressed recombination: PL intensity was significantly weakened with the addition of SnO2, indicating reduced carrier recombination.
  • Maximum PCE of 14.63%: The best-performing planar perovskite solar cell using the optimized SnO2 ETL achieved a power conversion efficiency of 14.63%, with a Voc of 994.98 mV, Jsc of 21.94 mA·cm⁻², and FF of 67.01%.
  • Good repeatability: Histograms of device parameters for 30 PSCs demonstrated good repeatability of the results.

Limitations and Future Work

  • Optimization of parameters: While the study identified an optimal sputtering time of 20 minutes, the authors suggest that further improvements can be made by optimizing other parameters of the reactive sputtering process.
  • Long-term stability: The paper focuses on achieving high efficiency. Further investigation into the long-term operational stability of these SnO2 ETL-based PSCs would be valuable for commercialization.
  • Scalability: Although the sputtering method is inherently scalable, detailed studies on large-area deposition and uniformity would be beneficial.
  • Comparison with other ETLs: While SnO2 is compared to TiO2 in the introduction, a more direct comparative study of the optimized sputtered SnO2 against other state-of-the-art ETLs in similar device architectures would strengthen the findings.

Summary updated

Abstract

Currently, tin oxide (SnO2) is a highly sought-after semiconductor material used in perovskite solar cells (PSCs) because of its good transmittance, the appropriate energy level, high electron mobility, high conductivity, ideal band gap and excellent chemical stability. In this study, SnO2 film was successfully prepared by radio frequency reactive magnetron sputtering (RS) under room temperature conditions. The obtained SnO2 thin films not only exhibited high transmittance in the visible region as well as the pure phase, but also had a suitable energy band structure and lower surface roughness than FTO (SnO2:F) glass substrate, which contributes to the improvement of the adjacent interface morphology. The SnO2 films prepared by reactive sputtering could effectively suppress carrier recombination and act as an electron transport layer. Moreover, the maximum efficiency of the device based on reactive sputtering of SnO2 as the electron transport layer (ETL) for planar perovskite solar cells (PSCs) was 14.63%. This study mainly described the preparation of SnO2 by reactive sputtering under room temperature conditions.
BibTeX
@inproceedings{sun2019reactive,
  author = {Wenhai Sun and Shuo Wang and Shina Li and Miao Xu and Yu Zhu and Du Chen and Ruixin Ma and Chengyan Wang},
  title = {{Reactive-Sputtered Prepared Tin Oxide Thin Film as an Electron Transport Layer for Planar Perovskite Solar Cells}},
  booktitle = {Coatings},
  year = {2019},
  doi = {10.3390/coatings9050320},
}
Figure