Reactive Ceramic Membrane for Efficient Micropollutant Purification with High Flux by LED Visible-Light Photocatalysis: Device Level Attempts

Shuo Li, Xuan Zhang, Rui Fang, Zhiliang Cheng, Qian Xu, Shu Ma, Jie Xiong, Peng Chen, Guangjie FengCrystals 2023 · DOI

TL;DR

This paper presents a novel, large-scale photocatalytic reactive ceramic membrane (PRCM) system that efficiently removes micropollutants (MPs) like tetracycline hydrochloride from water using visible LED light. The system achieves high purification rates and flux, demonstrating a promising solution for advanced water treatment with potential for solar energy integration.

What Problem Does This Paper Address?

The world's water sources are increasingly contaminated with micropollutants (MPs) – persistent organic compounds from sources like pharmaceuticals, pesticides, and industrial chemicals. These MPs are present at very low concentrations but pose significant risks to human health and ecosystems due to their recalcitrance and potential for bioaccumulation. Traditional water treatment methods often struggle with these contaminants, requiring high energy input, low efficiency, and sometimes producing harmful disinfection byproducts. While membrane separation techniques like nanofiltration and reverse osmosis are effective, they are prone to fouling. This paper addresses the need for an efficient, low-cost, and anti-fouling method for MP removal, specifically by combining advanced oxidation with membrane technology.

Methods

The core of this research is the development of a Nitrogen-doped Titanium Dioxide Ceramic Membrane (N-TiO₂-CM). The process involved:

  • N-TiO₂ Nanoparticle Synthesis: Nitrogen-doped TiO₂ (N-TiO₂) nanoparticles were synthesized using a sol-gel method, with varying nitrogen-to-titanium ratios. The optimal ratio (N-TiO₂-1) was selected based on photocatalytic activity.
  • N-TiO₂ Coating on Ceramic Membrane: A large, planar ceramic membrane (CM) was coated with the synthesized N-TiO₂ nanoparticles using a facile dip-coating method. This process was repeated three times to achieve optimal loading without significantly compromising water flux.
  • PRCM Module Fabrication: The coated ceramic membrane was then integrated into a module for a fixed-bed reactor system.
  • Fixed-Bed Reactor System: A custom-built fixed-bed reactor was designed, incorporating the N-TiO₂-CM module, visible LED light sources (405 nm), and pumps for circulating the wastewater and collecting permeate.
  • Characterization: The N-TiO₂ nanoparticles and the N-TiO₂-CM were thoroughly characterized using techniques like X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray Spectroscopy (EDS), Transmission Electron Microscopy (TEM), X-ray Photoelectron Spectroscopy (XPS), UV-Vis Diffuse Reflectance Spectroscopy (DRS), and Fourier Transform Infrared Spectroscopy (FT-IR) to confirm their structure, morphology, composition, and optical properties.
  • Performance Evaluation: The system's performance was evaluated by measuring the degradation rate of tetracycline hydrochloride (TC) as a model MP and the permeate flux under visible LED irradiation. Radical scavenging experiments were conducted to identify the key reactive species responsible for degradation.

Datasets

The study did not use pre-existing datasets for training or evaluation. Instead, it generated its own experimental data through the performance evaluation of the developed PRCM system. The primary "dataset" consisted of:

  • Tetracycline Hydrochloride (TC) Aqueous Solutions: Prepared at an initial concentration of 20 mg/L for testing the removal efficiency.
  • Pure Water: Used to measure the pure water flux of the ceramic membranes.

Key Insights and Ideas

  • Synergistic Effect of N-Doping and Photocatalysis: Doping TiO₂ with nitrogen significantly enhances its visible light absorption and photocatalytic activity. This is attributed to the narrowing of the bandgap energy, allowing for better utilization of visible LED light.
  • Facile and Scalable Fabrication: The dip-coating method for loading N-TiO₂ onto the ceramic membrane is straightforward and amenable to producing larger membrane modules, suggesting good potential for industrial scale-up.
  • High Flux and Self-Cleaning Properties: The N-TiO₂-CM not only effectively degrades MPs but also exhibits improved permeate flux and self-cleaning characteristics compared to the bare ceramic membrane. This suggests that the photocatalytic process helps to mitigate membrane fouling.
  • Dominant Reactive Species: Quenching experiments revealed that hydroxyl radicals (•OH) and superoxide radicals (•O₂⁻) are the primary reactive species responsible for the degradation of TC in this system.
  • Potential for Solar Energy Integration: The use of visible LED light highlights the system's compatibility with solar energy, offering a cost-effective and sustainable approach for MP treatment.

Key Results

  • High MP Removal Efficiency: The N-TiO₂-CM system achieved a remarkable 92% removal efficiency of tetracycline hydrochloride (TC) within 270 minutes, even at an initial concentration of 20 mg/L.
  • Enhanced Degradation Rate: The degradation rate constant (k) for TC using N-TiO₂-CM was 2.57 times higher than that of the bare ceramic membrane.
  • Improved Permeate Flux: The permeate flux of the N-TiO₂-CM was 2.30 times higher than that of the bare CM, indicating improved anti-fouling properties. The pure water flux reached 2114.2 L/(m² × h) under a trans-membrane pressure (TMP) of -92 kPa.
  • Reduced Bandgap Energy: N-doping reduced the bandgap energy of TiO₂ from 3.10 eV to 2.70 eV, enhancing visible light absorption.
  • Uniform Nanoparticle Loading: SEM/EDS analysis confirmed that the N-TiO₂ nanoparticles were uniformly and tightly loaded onto the ceramic membrane surface.

Limitations and Future Work

  • Pore Size Distribution Impact: While the N-TiO₂ loading improved photocatalytic performance, it did lead to a decrease in the average pore diameter of the ceramic membrane, which is a trade-off for achieving higher flux.
  • Scale-up Design and Simulation: The paper proposes a pilot-scale equipment diagram but acknowledges that industrial reactor design and process simulation of the flow field are still needed.
  • Long-term Reusability and Stability: While the study indicates good self-cleaning properties, further research on the long-term reusability and stability of the N-TiO₂-CM under continuous operation would be beneficial.
  • Broader MP Spectrum: The study focused on TC as a model MP. Future work could explore the effectiveness of this system for a wider range of emerging micropollutants.
  • Optimization of Loading Layers: Although three loading layers were found to be optimal, further fine-tuning of the coating process could potentially yield even better results.

Summary updated

Abstract

Micropollutants (MPs) are widely occurring in surface water all over the world with extremely low concentrations, and their treatment requires high energy consumption and efficiency. In this study, a large-sized planar photocatalytic reactive ceramic membrane (PRCM) was prepared using the facile dip-coating method with nitrogen-doped TiO2 (N-TiO2-CM) for the purification of tetracycline hydrochloride (TC) as a model MP. The N-TiO2 nanoparticles and the as-prepared N-TiO2-CM were characterized by SEM/EDS, TEM, XPS, UV–Vis DRS, and FT-IR. A fixed bed reactor integrated N-TiO2-CM, and visible LED light was fabricated for the new PRCM water treatment system for the removal of TC with a comprehensive consideration of the degradation rate and permeate flux. The SEM/EDS results indicated that the N-TiO2 was uniformly and tightly loaded onto the flat CM, and the pure water flux could reach over 2000 L/(m2 × h) under a trans-membrane pressure (TMP) of −92 kPa. The fixed bed PRCM water treatment system is extremely suited for MP purification, and the removal efficiency of TC was as high as 92% with 270 min even though its initial concentration was as low as 20 mg/L. The degradation rate and permeate flux of N-TiO2-CM was 2.57 and 2.30 times as high as that of the CM, indicating its good self-cleaning characteristics. The quenching experiments illustrated that the reactive radicals involved in the PRCM process, •OH and •O2−, were responsible for TC degradation. This research also provides a utilization proposal for a scale-up N-TiO2-CM system for water and wastewater treatment.
BibTeX
@inproceedings{li2023reactive,
  author = {Shuo Li and Xuan Zhang and Rui Fang and Zhiliang Cheng and Qian Xu and Shu Ma and Jie Xiong and Peng Chen and Guangjie Feng},
  title = {{Reactive Ceramic Membrane for Efficient Micropollutant Purification with High Flux by LED Visible-Light Photocatalysis: Device Level Attempts}},
  booktitle = {Crystals},
  year = {2023},
  doi = {10.3390/cryst13040651},
}
Figure