Range-Resolved Bistatic Imaging Lidar Using a CCD Camera.

Kenji Yamaguchi, Kazuo Meki, Yasunori Saito, Tetsuo Kano, Akio Nomura, Toshikazu Itabe, Takashi ShibataThe Review of Laser Engineering 1995 · DOI

Abstract: In this work, we studied the feasibility of a range-resolved bistatic imaging lidar using a CCD camera. The theoretical study revealed that the bistatic imaging lidar could successfully receive a wide height range A-scope signal without range correction and also without alignment for field of view overlapping, although height resolution decreased with height. Field experimental results confirmed these theoretical predictions and showed that the bistatic imaging lidar was a powerful tool for measuring the lower atmosphere, especially near the surface of the earth.

Introduction

Traditional monostatic lidar systems, where the transmitter and receiver are co-located, face significant challenges in atmospheric monitoring. They typically suffer from a "blind spot" at low altitudes due to incomplete overlap between the laser beam and the receiver's field of view (FOV). Furthermore, the signal strength decays according to the inverse-square law ($1/r^2$), necessitating detectors with extremely high dynamic range to capture both near-field and far-field signals. While bistatic lidars (separated transmitter and receiver) can mitigate the overlap issue, they often require complex mechanical scanning to generate vertical profiles. This paper presents a bistatic imaging lidar system that utilizes a high-sensitivity CCD camera to capture an entire range-resolved vertical profile in a single exposure, eliminating the need for range correction and tedious alignment.

Methods

The experimental setup consists of a pulsed Nd:YAG laser (532 nm) as the transmitter and a cooled, high-sensitivity CCD camera as the receiver. The laser is directed vertically into the atmosphere. The CCD camera is positioned at a baseline distance ($l$) from the laser and tilted to intersect the beam.

Geometric configuration of the bistatic imaging lidar system showing the relationship between altitude $z$, baseline $l$, and the scattering volume $V$.

In this configuration, each pixel in a vertical column of the CCD corresponds to a specific altitude ($z$). This allows for the instantaneous capture of an "A-scope" (signal vs. height) profile. To minimize thermal noise, the CCD is cooled to -30°C, enabling long exposure times (up to 15 minutes) for high-altitude measurements. Background light is removed using an "ON/OFF" subtraction method, where an image taken without the laser is subtracted from one taken with the laser pulse.

Key Insights and Ideas

A primary advantage of this bistatic imaging geometry is the inherent cancellation of the $1/r^2$ signal attenuation. As the distance to the scattering volume increases, the physical volume "seen" by a single pixel also increases. This geometric effect almost perfectly offsets the inverse-square drop-off, resulting in a signal that is relatively uniform across a wide range of altitudes. This significantly reduces the dynamic range requirements for the detector.

Additionally, the system is robust against alignment errors. As long as the laser beam remains within the camera's wide FOV, the signal is captured, making it far easier to deploy than monostatic systems requiring sub-milliradian precision. However, there is a trade-off: the height resolution ($\Delta z$) is not constant and degrades as the square of the altitude increases.

Key Results

The system was validated through field campaigns targeting different atmospheric layers. A short baseline (4m) was used at Shinshu University to map aerosol variations in the lower 1km of the atmosphere, successfully capturing structural changes over several hours. For stratospheric studies, a 215m baseline was employed at the Communications Research Laboratory in Tokyo. This setup successfully detected the stratospheric aerosol layer at 25km altitude resulting from the 1991 Mt. Pinatubo eruption.

Field experimental setup showing the CCD camera mounted on a tripod, demonstrating the system's portability.

Quantitative comparisons with traditional monostatic lidar data showed excellent agreement in scattering ratio profiles. The compact nature of the receiver, which uses standard camera lenses, highlights the potential for low-cost, portable atmospheric monitoring stations.

Limitations and Future Work

Currently, the system is limited to nighttime operation because the CCD's integration time would lead to saturation from daytime background noise. Future iterations could incorporate synchronized high-speed shutters to enable daytime use. Furthermore, while the system excels at lower altitudes, the decreasing height resolution at higher altitudes and the current quantum efficiency of CCD sensors (approx. 8.4% at 532nm) are areas for improvement with more advanced sensor technology.

Summary updated

Abstract

In this work, we studied the feasibility of a range resolved bistatic imaging lidar using a CCD camera. The theoretical study revealed that the bistatic imaging lidar could successfully receive a wide height range A-scope signal without range correction and also without alignment for field of view overlapping, although height resolution decreased with height. Field experimental results confirmed these theoretical predictions and showed that the bistatic imaging lidar was a powerful tool for measuring the lower atmosphere, especially near the surface of the earth.
BibTeX
@article{yamaguchi1995range,
  author = {Kenji Yamaguchi and Kazuo Meki and Yasunori Saito and Tetsuo Kano and Akio Nomura and Toshikazu Itabe and Takashi Shibata},
  title = {{Range-Resolved Bistatic Imaging Lidar Using a CCD Camera.}},
  journal = {The Review of Laser Engineering},
  year = {1995},
  doi = {10.2184/lsj.23.25},
}
Figure