TL;DR
This paper presents a "quasi-all-passive" thermal control system (TCS) for the Luojia 1-01 small satellite, addressing challenges of low heat inertia and limited power/mass budgets. The system was successfully validated through ground thermal balance tests and on-orbit telemetry, demonstrating stable temperatures for critical components and overall system functionality.
What Problem Does This Paper Address?
Small satellites, like the Luojia 1-01, face significant thermal control challenges due to their small size, low heat inertia, and limited power and mass budgets. These constraints make traditional active thermal control systems impractical. The Luojia 1-01, in particular, experiences large temperature fluctuations due to its structure's poor thermal conductivity and the frequent switching of its operational modes. This paper aims to design and validate a thermal control system that can maintain critical components within their operational temperature ranges without relying heavily on active heating or cooling, thus conserving precious power and mass.
Methods
The authors employed a multi-faceted approach to design and validate their quasi-all-passive TCS:
- Isothermal Cabin Design: The core strategy was to create an "isothermal cabin" where only the most critical components (camera and battery) receive active thermal control. Other instruments are managed passively.
- Thermal Analysis: A finite element model (FEM) was developed using I-DEAS/TMG software to simulate the thermal behavior of the satellite under various conditions. This model was crucial for understanding heat transfer and identifying potential thermal issues.
- Heat Insulation Design: Multi-layer insulation (MLI) blankets were extensively used to minimize heat exchange with the external environment. Heat-insulating pads were also employed at contact surfaces to reduce unwanted heat conduction.
- Heat Conduction Design: To counteract the poor inherent thermal conductivity of the satellite structure (exacerbated by shock absorbers), conductive grease and thermal conductive membranes were used to improve heat transfer between components and mounting panels.
- Heat Dispersion Design: Specific surfaces on the satellite (+Y and -Y panels) were designated as radiating regions and coated with specialized materials (HA95 and F46) to efficiently dissipate heat into space.
- Heating Design: Active heating circuits were implemented only for the camera and battery, with backup systems, to maintain their temperatures within tight operational limits.
- Ground Thermal Balance Test: The flight model of the satellite underwent rigorous thermal balance testing under simulated high and low temperature conditions to verify the TCS design before launch.
- On-Orbit Validation: Telemetry data from the deployed Luojia 1-01 satellite was analyzed to assess the real-world performance of the TCS.
- Thermal Model Modification: The FEM was updated and refined based on the data obtained from both ground tests and on-orbit operations to improve its predictive accuracy.
Datasets
Not discussed in the paper. The paper focuses on the design and validation of a thermal control system for a specific satellite, using its own telemetry and test data.
Key Insights and Ideas
- "Quasi-All-Passive" is Achievable: The study demonstrates that a thermal control system can be highly effective even with minimal active components, provided a well-thought-out passive design strategy. This is crucial for resource-constrained small satellites.
- Targeted Active Control is Key: Focusing active heating/cooling resources only on the most critical components (camera, battery) is a highly efficient strategy for small satellites.
- Material Selection Matters: The choice of coatings, MLI, and conductive materials significantly impacts thermal performance. The paper details specific materials used for different functions.
- Shock Absorbers are a Thermal Challenge: The paper explicitly identifies shock absorbers as a factor that reduces thermal conductivity, necessitating specific design considerations (like conductive grease) to overcome this.
- Model-Based Design and Validation Loop: The iterative process of thermal analysis, ground testing, and on-orbit validation, followed by model refinement, is essential for ensuring the success of complex thermal control systems.
Key Results
- On-Orbit Performance:
- Camera temperature stabilized around 12 °C.
- Battery temperature stabilized around 19 °C.
- Temperatures of instruments inside the cabin ranged from 10 °C to 25 °C.
- Temperature fluctuation of the optical camera was less than 2 °C when not imaging.
- Temperature fluctuation of instruments not facing the sun was less than 4 °C.
- Ground Thermal Balance Test: Results showed that all instruments were well-controlled within their required temperature ranges, with margins.
- Thermal Model Accuracy: After modification based on in-orbit data, the thermal model showed a temperature difference of within 3 °C compared to in-orbit and ground test data, indicating effective model improvement.
- Power Consumption: The active heating circuits consumed a total of 1.68 W on-orbit, well within the allocated power budget.
Limitations and Future Work
- Limitations:
- The paper acknowledges that the TCS design is a compromise due to limited mass and power.
- The "quasi-all-passive" nature means that some instruments are exposed to wider temperature fluctuations than actively controlled ones.
- The study is specific to the Luojia 1-01 satellite, and direct application to other satellites might require re-evaluation.
- Future Work:
- The authors suggest that this quasi-all-passive TCS provides a valuable reference for the thermal design of other small and micro satellites with similar constraints.
- The successful model modification indicates potential for further refinement of thermal analysis techniques for small satellites.
Summary updated