PTC Self-Heating Experiments and Thermal Modeling of Lithium-Ion Battery Pack in Electric Vehicles

Chengning Zhang, Xin Jin, Junqiu LiEnergies 2017 · DOI

TL;DR

This paper introduces a novel "PTC self-heating" method for lithium-ion battery packs in electric vehicles (EVs) that allows them to operate independently of external power in cold conditions. By using the battery's own discharge to power positive temperature coefficient (PTC) materials, the system effectively heats the battery pack, leading to improved discharge capacity and more uniform temperature distribution compared to external heating methods.

What Problem Does This Paper Address?

Lithium-ion batteries (LIBs) experience a significant drop in discharge rate and capacity at low temperatures. This performance degradation severely impacts the range, dynamic performance, and overall usability of electric vehicles (EVs) in cold climates. While heating the battery pack is a known solution, existing methods often rely on external power sources, which are not always available, especially in remote or off-grid cold environments. This creates a need for a self-sufficient heating solution that can maintain battery performance without external grid connection.

Methods

The core of this research is the development and experimental validation of a PTC self-heating method. This involves integrating PTC materials within the battery pack. When the battery operates at low temperatures, it discharges a small amount of energy to power these PTC elements. PTC materials have a unique property: their electrical resistance increases sharply above a certain "Curie temperature." This characteristic allows them to generate heat efficiently when cold and self-regulate to prevent overheating as the battery warms up.

The researchers conducted three comparative heating experiments:

  1. External power source heating: Using a standard 220V AC supply to power the PTC elements.
  2. Self-heating Experiment I: Using the battery pack itself (at 100% State of Charge - SOC) as the power source for the PTC elements.
  3. Self-heating Experiment II: Using the battery pack (at 60% SOC) as the power source.

Following the heating phases, the researchers performed Hybrid Pulse Power Characteristic (HPPC) tests and 1C constant-current (CC) discharge tests to evaluate the recovery of the battery pack's charge/discharge capabilities.

To further understand the heating mechanism and temperature distribution, a thermal model was developed. This involved establishing a geometric model of the battery pack and analyzing both internal heat generation (from battery resistance) and external heat generation (from PTC materials). The model was then used for numerical simulations to predict temperature variations.

Datasets

The paper utilizes experimental data collected from a 35Ah square aluminum-plastic-film LiMn2O4 cell. Specific experimental conditions involved charging and discharging at various temperatures (-40°C to 20°C) and discharge rates (0.3C, 1C, 2C). The experiments were conducted using a Digatron EVT500-500 battery tester and an incubator to control ambient temperature. No new benchmark datasets were introduced; rather, the study relies on the performance of the battery under controlled experimental conditions.

Key Insights and Ideas

  • Self-Sufficiency is Key: The most significant insight is the demonstration that a battery pack can effectively heat itself using its own energy, enabling independent operation in extreme cold without external power. This is a crucial step towards more robust EV performance in diverse climates.
  • PTC's Smart Heating: The inherent self-regulating nature of PTC materials is a major advantage. They provide substantial heating when needed (low temperature) and automatically limit heat output to prevent overheating, ensuring battery safety and longevity.
  • Internal Heat Matters: While the external PTC heating is the primary driver, the paper highlights that the internal heat generated by the battery's own resistance during discharge also contributes significantly to the overall heating and capacity recovery. This internal heat, though smaller in magnitude, plays a vital role in achieving uniform temperature distribution.
  • SOC's Influence: The State of Charge (SOC) of the battery pack directly impacts the effectiveness of self-heating. Higher SOC (100%) leads to better heating performance and faster recovery of discharge capabilities compared to lower SOC (60%).

Key Results

  • Improved Discharge Capacity: The self-heated battery pack (Self-heating Experiment I) showed a significantly higher 1C CC discharge capacity (19.834 Ah) compared to the pack heated by an external power source (12.853 Ah), even when the self-heated pack started at a lower SOC after heating.
  • Faster Heating Rate (External vs. Self): The external power source heating achieved a higher heating rate (0.629 °C/min) in the first stage compared to self-heating (0.459 °C/min for Self-heating I). However, the self-heating method still provided substantial heating.
  • Temperature Uniformity: Thermal modeling and simulation confirmed that the PTC self-heating method results in good temperature distribution uniformity within the battery pack after heating. For instance, in the first heating process, the maximum temperature difference within the pack was 4.67 °C.
  • Performance Recovery: After heating, the battery pack's pulse discharge capability improved considerably. For example, after the second heating in Self-heating Experiment I, the pack could be discharged at a 3C rate, a significant improvement from its performance before heating.

Limitations and Future Work

  • Energy Consumption: The self-heating process does consume some of the battery pack's energy (approximately 13% of total pack energy in the experiments). While this is a trade-off for performance, it's a factor to consider.
  • SOC Dependency: The effectiveness of self-heating is dependent on the initial SOC. If the SOC is too low, self-heating might not be sufficient, and an external power source might be necessary.
  • Future Work: The authors propose to develop strategies that combine the advantages of both internal and external heating to mitigate the limitations imposed by initial SOC. They also aim to further refine the thermal model to better predict temperature distribution and optimize the self-heating system.

Summary updated

Abstract

This paper proposes a positive temperature coefficient (PTC) self-heating method, in which EVs can be operated independently of external power source at low temperature, with a lithium-ion battery (LIB) pack discharging electricity to provide PTC material with power. Three comparative heating experiments have been carried out respectively. With charge/discharge tests implemented, results demonstrate the superiority of the self-heating method, proving that the discharge capability, especially the discharge capacity of the self-heated pack is better than that of the external power heated pack. In order to evaluate the heating effect of this method, further studies are conducted on temperature distribution uniformity in the heated pack. Firstly, a geometric model is established, and heat-generation rate of PTC materials and LIB are calculated. Then, thermal characteristics of the self-heating experiment processes are numerically simulated, validating the accuracy of our modeling and confirming that temperature distributions inside the pack after heating are kept in good uniformity. Therefore, the PTC self-heating method is verified to have a significant effect on the improvement of performance of LIB at low temperature.
BibTeX
@inproceedings{zhang2017ptc,
  author = {Chengning Zhang and Xin Jin and Junqiu Li},
  title = {{PTC Self-Heating Experiments and Thermal Modeling of Lithium-Ion Battery Pack in Electric Vehicles}},
  booktitle = {Energies},
  year = {2017},
  doi = {10.3390/en10040572},
}
Figure