Propiedades mecánicas del hormigón corroído por la lluvia ácida con base en el elemento discreto de partículas (Editado por el Dr. Kimon Christianis, University of Patras, Greece)

Guang Yang, Guoxin LiRevista 2022 · DOI

TL;DR

Researchers have developed a high-fidelity meso-mechanical model using the Particle Discrete Element Method (DEM) to predict how acid rain degrades the strength of prestressed concrete. By simulating the "granular" nature of concrete rather than treating it as a solid block, this approach achieves near-perfect alignment with experimental data, offering a powerful tool for predicting the service life of aging infrastructure.

What Problem Does This Paper Address?

Acid rain is a silent killer for infrastructure, particularly in industrial regions. When sulfate ions from acid rain penetrate concrete, they react with cement hydration products to cause expansion and internal fracturing. For prestressed concrete—often used in high-rise buildings and bridges—this corrosion is even more dangerous because the internal steel strands are under high tension; a sudden snap can lead to catastrophic failure without warning.

The challenge lies in modeling this decay. Traditional Finite Element Method (FEM) analysis treats concrete as a continuous medium. However, concrete is inherently non-uniform, and cracks are, by definition, discontinuities. FEM often struggles to accurately simulate the complex "crushing and spalling" behavior of corroded concrete. The authors sought a more granular approach to bridge the gap between theory and real-world failure.

Methods

The study combines physical experimentation with advanced numerical simulation:

  1. Experimental Corrosion: The team fabricated eight prestressed concrete beams and subjected them to "accelerated corrosion" using electrified immersion in a simulated acid rain solution (pH 2.3). This allowed them to achieve years' worth of environmental damage in just 30 to 90 days.
  2. Impact Testing: They used a Split Hopkinson Pressure Bar (SHPB) to conduct impact splitting tests, measuring how the corroded beams handled sudden, high-energy loads.
  3. Particle Discrete Element Method (DEM): This is the paper's core innovation. Instead of a solid mesh, they modeled concrete as a collection of discrete particles (aggregates and mortar) bonded together.
  4. Meso-mechanical Modeling: They identified three distinct components: the aggregate, the mortar, and the interface between them.
  5. Contact Constitutive Model: They applied laws governing how these particles interact—specifically, when bonds between particles break (rupture) or slide (slip) under stress.

Datasets

While not a traditional "big data" study, the researchers generated a specific experimental dataset to validate their model:

  • Test Specimens: 8 prestressed concrete beams (labeled TYL-a through TYL-h) with varying concrete strengths (H45, H55, H65), different reinforcement ratios, and simulated corrosion rates ranging from 0% to 10%.
  • Comparative Benchmarks: The DEM results were benchmarked against traditional FEM analysis, standard regression models, and the "actual" physical test results.

Key Insights and Ideas

  • The "Granular" Advantage: The move from continuum mechanics (FEM) to discrete mechanics (DEM) is the "aha moment." By treating concrete as a collection of particles that can move and separate, the model naturally captures the "dispersion" and "motion" of material failure that FEM misses.
  • Three Stages of Failure: The study identifies a clear three-step stress process for corroded beams:
  • Uncracking: The elastic stage where the beam holds firm.
  • Crack Increasing: Micro-cracks begin to propagate as load increases.
  • Crushing and Spalling: The final stage where the material literally falls apart.
  • Inverse Proportionality: The relationship is stark—as the corrosion rate of the steel strand increases, the splitting tensile strength of the concrete drops linearly.
  • Reinforcement Matters: The beam with the upper tensile reinforcement (TYL-b) maintained the highest strength, while the beam with the highest corrosion and lower compression reinforcement (TYL-d) was the weakest.

Key Results

The DEM model demonstrated remarkable accuracy. In the splitting tensile strength tests across various air pressures:

  • High Precision: For beam TYL-d at 0.13 MPa, the DEM model predicted a strength of 4.94 MPa, while the actual experimental value was 4.93 MPa.
  • Outperforming FEM: In almost every test case, the DEM results were closer to the actual values than the Finite Element Method. For example, in one test, FEM over-predicted strength by nearly 10%, while DEM remained within a 1% margin of error.
  • Practical Utility: The model successfully captured the inflection points in load-displacement curves, providing a reliable "early warning" signature for structural distress.

Limitations and Future Work

The authors acknowledge a few areas where the model could be refined:

  • Natural vs. Accelerated: The electrified immersion method is a standard lab shortcut, but it doesn't perfectly mimic the slow, chemical-mechanical coupling of decades-long natural acid rain exposure.
  • Short-term Loading: The current study focuses on impact and short-term loads. Future research needs to address how these corroded beams behave under long-term, sustained "creep" loads.
  • Environmental Complexity: The study focuses on acidity and sulfate ions; future iterations could incorporate temperature fluctuations and freeze-thaw cycles to create a truly "all-weather" durability model.

Summary updated

Abstract

Para predecir la durabilidad de la estructura de hormigón y garantizar la seguridad de la vida y la propiedad, se presenta un método para analizar las propiedades mecánicas del hormigón corroído por la lluvia ácida con base en el elemento discreto de partículas. Se diseñaron ocho muestras de prueba de vigas de hormigón pretensado, y luego se obtuvieron muestras de prueba de vigas de hormigón con diferentes tasas de corrosión mediante la simulación de la corrosión por lluvia ácida. La prueba de división de impacto se llevó a cabo con base el elemento discreto de partículas y luego se construyó el modelo mesomecánico de elemento discreto de partículas de hormigón. Los resultados del experimento muestran que el proceso de estrés de la viga de hormigón de prueba después de la corrosión por lluvia ácida incluye tres etapas: desmonoramiento, aumento de la grieta por la carga, trituración y astillado. Después de la corrosión por lluvia ácida, la resistencia a la tracción de división del haz TYL-b (el refuerzo de tracción superior) es la más alta, y la resistencia a la tracción de división del haz TYL-d (el refuerzo de compresión inferior) es la más baja. La tasa de corrosión de la lluvia ácida es inversamente proporcional a la resistencia a la tracción de división del hormigón. La resistencia a la tracción por hendimiento del hormigón después de la corrosión por lluvia ácida obtenida por el método propuesto es coherente con el valor real. Por lo tanto, el método propuesto tiene una alta precisión y un alto valor práctico.
BibTeX
@inproceedings{yang2022propiedades,
  author = {Guang Yang and Guoxin Li},
  title = {{Propiedades mecánicas del hormigón corroído por la lluvia ácida con base en el elemento discreto de partículas (Editado por el Dr. Kimon Christianis, University of Patras, Greece)}},
  booktitle = {Revista},
  year = {2022},
  doi = {10.20937/rica.54615},
}
Figure