Preparation and Failure Behavior of Gel Electrolytes for Multilayer Structure Lithium Metal Solid-State Batteries

Chen Chu, Wang Qin, Qiankun Hun, Yujiang Wang, Xinghua Liang, R.-s. Tan, Jinping Li, Yifeng GuoGels 2025 · DOI

TL;DR

This paper investigates the performance and failure mechanisms of multilayer lithium metal solid-state batteries using a novel PVDF-HFP/PAN-LiClO4-LLZTO gel polymer electrolyte. They found that while multilayer designs offer higher initial capacity at low rates, single-layer batteries exhibit superior long-term stability and significantly lower interfacial impedance increase over cycling, suggesting a path towards more robust high-capacity solid-state batteries.

What Problem Does This Paper Address?

The quest for safer and higher-energy-density batteries has led to significant interest in solid-state lithium batteries (SSLBs). Unlike traditional liquid electrolyte batteries, SSLBs eliminate flammable liquid electrolytes, greatly enhancing safety. However, a major hurdle for high-capacity SSLBs, particularly those with multilayer designs, is their poor cycle life and a substantial performance gap compared to theoretical expectations. This paper aims to understand the failure mechanisms in multilayer SSLBs and compare their performance and stability against single-layer counterparts, using a newly developed gel polymer electrolyte (GPE).

Methods

The researchers prepared a novel gel polymer electrolyte (GPE) by UV curing a mixture of polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP), polyacrylonitrile (PAN), lithium perchlorate (LiClO4), and lithium lanthanum zirconium tantalate (LLZTO). This GPE was then used to assemble both single-layer and three-layer soft-pack lithium metal solid-state batteries.

Key characterization techniques employed include:

  • X-ray Diffraction (XRD) and Raman Spectroscopy: To analyze the structural changes in the GPE after cycling.
  • Thermogravimetric Analysis (TGA): To assess the thermal stability of the GPE.
  • Scanning Electron Microscopy (SEM): To observe the surface morphology and cross-sections of the GPE before and after cycling.
  • X-ray Photoelectron Spectroscopy (XPS): To investigate the chemical composition and changes at the electrode-electrolyte interface.
  • Electrochemical Impedance Spectroscopy (EIS): To track the evolution of interfacial impedance over cycling.
  • Cyclic Voltammetry (CV): To evaluate the electrochemical performance and lithium-ion insertion/extraction behavior.
  • Galvanostatic Charge-Discharge Cycling: To assess the rate capability and cycle life of the batteries.

Datasets

Not discussed in the paper. The study focuses on experimental synthesis and characterization of battery components and assembled cells.

Key Insights and Ideas

  • Multilayer vs. Single-Layer Trade-off: While multilayer batteries can achieve higher initial discharge capacities at low rates (0.1 C), this advantage quickly diminishes at higher rates (0.5 C and above). This suggests that the internal structure of multilayer designs may hinder ion transport under demanding conditions.
  • Interfacial Impedance is Key: The primary failure mechanism identified is the significant increase in interfacial impedance over cycling, particularly in the multilayer configurations. This impedance rise directly correlates with capacity fade.
  • Structural Degradation: Post-cycling analysis (SEM, XRD, Raman) reveals structural deterioration in the GPE, including crack formation, loosening of layered structures, and disappearance of characteristic diffraction peaks, especially in multilayer cells. This indicates that the ion transport pathways within the electrolyte are compromised.
  • LiF Passivation: XPS analysis suggests that the presence of LiF in the solid electrolyte interface (SEI) layer plays a positive role in slowing dendrite formation. The study notes a downward trend in LiF content in multilayer structures after cycling, potentially impacting passivation effectiveness.
  • Safety Demonstrated: Despite structural and performance challenges, the assembled soft-pack batteries (both single and multilayer) demonstrated high safety, remaining functional after bending, cutting, and needle puncture tests.

Key Results

  • Interfacial Impedance: After 100 cycles, the interfacial impedance of the three-layer battery increased by 9.61 times compared to single-layer batteries. Specifically, it rose from 17 Ω to 42 Ω for the three-layer, versus 2.2 Ω to 4.8 Ω for the single-layer.
  • Capacity Retention: After 100 cycles at 0.2 C, the capacity retention for the single-layer battery was 48.9%, while the three-layer battery retained only 15.6%.
  • Rate Performance: At 0.1 C, the three-layer battery showed a higher capacity (126.2 mAh g⁻¹) than the single-layer (106.3 mAh g⁻¹). However, at 0.5 C, the three-layer capacity dropped to 71.1 mAh g⁻¹ compared to 83.4 mAh g⁻¹ for the single-layer.

Limitations and Future Work

The authors acknowledge that the current testing is primarily at the laboratory level. For industrial application, they suggest:

  • Focus on Interfacial Impedance: Further research should concentrate on solving the interfacial impedance problem in multilayer structures.
  • Material Optimization: Exploring polymer-ceramic composite materials with different ratios and combinations could improve conductivity.
  • Environmental Adaptability: A systematic evaluation of the battery's performance at high and low temperatures is needed, as real-world environments are more complex than laboratory conditions.
  • Scale-Up Considerations: In-depth exploration of electrode material matching and packaging process optimization is crucial for industrialization.

Summary updated

Abstract

High safety gel polymer electrolyte (GPE) is used in lithium metal solid state batteries, which has the advantages of high energy density, wide temperature range, high safety, and is considered as a subversive new generation battery technology. However, solid-state lithium batteries with multiple layers and large capacity currently have poor cycle life and a large gap between the actual output cycle capacity retention rate and the theoretical level. In this paper, polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP)/polyacrylonitrile (PAN)-lithium perchlorate (LiClO<sub>4</sub>)-lithium lanthanum zirconium tantalate (LLZTO) gel polymer electrolytes was prepared by UV curing process using a UV curing machine at a speed of 0.01 m/min for 10 s, with the temperature controlled at 30 °C and wavelength 365 nm. In order to study the performance and failure mechanism of multilayer solid state batteries, single and three layers of solid state batteries with ceramic/polymer composite gel electrolyte were assembled. The results show that the rate and cycle performance of single-layer solid state battery with gel electrolyte are better than those of three-layer solid state battery. As the number of cycles increases, the interface impedance of both single-layer and three-layer electrolyte membrane solid-state batteries shows an increasing trend. Specifically, the three-layer battery impedance increased from 17 Ω to 42 Ω after 100 cycles, while the single-layer battery showed a smaller increase, from 2.2 Ω to 4.8 Ω, indicating better interfacial stability. After 100 cycles, the interface impedance of multi-layer solid-state batteries increases by 9.61 times that of single-layer batteries. After 100 cycles, the corresponding capacity retention rates were 48.9% and 15.6%, respectively. This work provides a new strategy for large capacity solid state batteries with gel electrolyte design.
BibTeX
@inproceedings{chu2025preparation,
  author = {Chen Chu and Wang Qin and Qiankun Hun and Yujiang Wang and Xinghua Liang and R.-S. Tan and Jinping Li and Yifeng Guo},
  title = {{Preparation and Failure Behavior of Gel Electrolytes for Multilayer Structure Lithium Metal Solid-State Batteries}},
  booktitle = {Gels},
  year = {2025},
  doi = {10.3390/gels11080573},
}
Figure