Preparation and Characterization of Graphene Oxide/Carbon Nanotube/Polyaniline Composite and Conductive and Anticorrosive Properties of Its Waterborne Epoxy Composite Coatings

Yufeng Li, Shibo Liu, Feng Feng, Yiming Li, Yahui Han, Xinyang Tong, Xiaohui GaoPolymers 2024 · DOI

TL;DR

This paper introduces a novel composite coating made from graphene oxide (GO), carbon nanotubes (CNT), and polyaniline (PANI) embedded in a waterborne epoxy resin (WEP). This new coating demonstrates significantly improved electrical conductivity and corrosion resistance compared to traditional coatings, making it suitable for applications like protecting grounding grids and oil storage tanks.

What Problem Does This Paper Address?

Metal materials are susceptible to corrosion, which reduces their lifespan and can lead to economic losses and safety hazards. While organic coatings are a common solution, they often have limitations. Pure resin coatings can be penetrated by corrosive agents through micropores, and they typically lack electrical conductivity, which is crucial for applications like electromagnetic interference (EMI) shielding or preventing static discharge. Existing conductive fillers have drawbacks such as high cost, poor chemical stability, or limited conductivity. This research aims to develop a single coating that effectively addresses both corrosion and conductivity challenges by synergistically combining three advanced nanomaterials.

Methods

The researchers prepared a GO/CNT/PANI nanocomposite filler using an in-situ polymerization method. Aniline (AN) was polymerized onto the surface of pre-treated carbon nanotubes (Ac-CNT) and graphene oxide (GO). This nanocomposite filler was then dispersed into a waterborne epoxy resin (WEP) to create the final composite coating.

The characterization of the materials and coatings involved a suite of standard techniques:

  • FT-IR spectroscopy: To identify functional groups and confirm chemical interactions.
  • X-ray Diffraction (XRD): To analyze crystal structures and phase composition.
  • Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM): To visualize the surface morphology, dispersion of fillers, and the structure of the composite.
  • Electrical Resistivity Measurement: Using a four-probe meter to quantify the coating's conductivity.
  • Electrochemical Impedance Spectroscopy (EIS) and Potentiodynamic Polarization Curves: To evaluate the corrosion protection performance in a 3.5% NaCl solution.
  • Salt Spray Test: To assess long-term corrosion resistance under harsh environmental conditions.
  • Mechanical Performance Tests: Including flexibility, adhesion, pencil hardness, and impact resistance.

Datasets

Not discussed in the paper.

Key Insights and Ideas

  • Synergistic Effect: The combination of GO, CNT, and PANI creates a synergistic effect that significantly enhances both conductivity and corrosion resistance, outperforming individual components or simpler combinations.
  • "Labyrinth Effect" and Barrier Properties: GO's layered structure and PANI's ability to form a dense film create a "labyrinth effect," hindering the penetration of corrosive media.
  • Conductive Network Formation: The interconnected network of GO, CNT, and PANI facilitates electron transfer, crucial for conductivity and preventing corrosion.
  • Optimal Filler Ratio is Key: The study highlights that there's an optimal ratio of GO, CNT, and PANI for achieving the best performance. Too much of any component can lead to agglomeration and reduced effectiveness. Specifically, 20% GO content in the filler showed the best results.
  • PANI as a Binder and Enhancer: PANI not only contributes to conductivity but also helps disperse CNTs and GO, and its terminal amino groups can react with the epoxy matrix, improving interfacial adhesion.

Key Results

  • Corrosion Resistance: The GO/CNT/PANI/WEP composite coating with 3.5% filler content exhibited excellent corrosion resistance.
  • Corrosion current density (Icorr) was as low as 4.53 × 10⁻⁸ A·cm⁻².
  • Electrochemical impedance was high, reaching 3.84 × 10⁶ Ω·cm².
  • After 480 hours in a salt spray test, only slight corrosion was observed, with no obvious corrosion spreading.
  • Electrical Conductivity: The resistivity of the composite coating was as low as 2.3 × 10⁴ Ω·cm, significantly lower than the 10⁶ Ω·cm threshold for effective conductivity.
  • Mechanical Properties: The optimized GO/CNT/PANI/WEP coating achieved good mechanical properties, including adhesion grade 0, flexibility of 5 mm, pencil hardness of 2H, and impact resistance of 50 cm.
  • Hydrophobicity: The contact angle increased with GO content, peaking at 73.7° with 20% GO, indicating improved hydrophobicity which contributes to corrosion resistance.

Limitations and Future Work

  • Agglomeration Issues: While the study optimized filler ratios, the authors acknowledge that excessive amounts of GO can still lead to agglomeration, negatively impacting dispersion and conductivity. CNTs are shown to help mitigate GO agglomeration.
  • Further Optimization: The paper suggests that further research could explore different preparation methods or modifications of the fillers to further enhance dispersion and synergistic effects.
  • Application Scope: The authors propose that this composite coating has broad applications, particularly in areas requiring both conductivity and corrosion protection, such as grounding grids and oil storage tank protection. Future work could focus on scaling up production and testing in real-world application scenarios.

Summary updated

Abstract

The organic coating on the surface is common and the most effective method to prevent metal materials from corrosion. However, the corrosive medium can penetrate the metal surface via micropores, and electrons cannot transfer in the pure resin coatings. In this paper, a new type of anticorrosive and electrically conductive composite coating filled with graphene oxide/carbon nanotube/polyaniline (GO/CNT/PANI) nanocomposites was successfully prepared by in situ polymerization of aniline (AN) on the surface of GO and CNT and using waterborne epoxy resin (WEP) as film-forming material. The structure and morphology of the composite were characterized using a series of characterization methods. The composite coatings were comparatively examined through resistivity, potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS), and salt spray tests. The results show that the GO/CNT/PANI/WEP composite coating exhibits excellent corrosion resistance for metal substrates and good conductivity when the mass fraction of GO/CNT/PANI is 3.5%. It exhibits a lower corrosion current density of 4.53 × 10<sup>-8</sup> A·cm<sup>-2</sup> and a higher electrochemical impedance of 3.84 × 10<sup>6</sup> Ω·cm<sup>2</sup>, while only slight corrosion occurred after 480 h in the salt spray test. The resistivity of composite coating is as low as 2.3 × 10<sup>4</sup> Ω·cm. The composite coating possesses anticorrosive and electrically conductive properties based on the synergistic effect of nanofillers and expands the application scope in grounding grids and oil storage tank protection fields.
BibTeX
@inproceedings{li2024preparation,
  author = {Yufeng Li and Shibo Liu and Feng Feng and Yiming Li and Yahui Han and Xinyang Tong and Xiaohui Gao and Xinyang Tong and Xiaohui Gao},
  title = {{Preparation and Characterization of Graphene Oxide/Carbon Nanotube/Polyaniline Composite and Conductive and Anticorrosive Properties of Its Waterborne Epoxy Composite Coatings}},
  booktitle = {Polymers},
  year = {2024},
  doi = {10.3390/polym16182641},
}
Figure