Preparation and Characterization of Al2O3/h-BN Composite Coatings by Atmospheric Plasma Spraying (APS)

Yifeng Guo, Lingxiao Lan, Boying Qin, Xinghua Liang, Yujiang Wang, Zhikun ChenCrystals 2024 · DOI

TL;DR

This paper presents Al₂O₃/h-BN composite coatings applied to corona rollers using atmospheric plasma spraying (APS). These coatings demonstrate improved electrical insulation, wear resistance, and adhesion compared to single-phase materials, making them a promising candidate for enhancing the performance and lifespan of high-voltage electrical components.

What Problem Does This Paper Address?

Corona rollers are critical components in modern tape casting equipment, operating under high-voltage electric fields for extended periods. This demanding environment necessitates materials with excellent electrical insulation, arc resistance, corona resistance, and flame retardancy. The generation of ozone during operation can lead to film breakdown and equipment failure. While protective coatings are used to enhance the durability of corona rollers, there's a need for advanced ceramic coatings that offer a superior combination of mechanical strength and electrical insulation properties to meet these stringent requirements.

Methods

The researchers employed Atmospheric Plasma Spraying (APS) to deposit Al₂O₃/h-BN composite coatings onto 20 steel substrates. This technique involves melting powder materials and spraying them at high velocity onto a surface. Two distinct coatings, labeled 'A' and 'B', were prepared using different APS parameters, specifically varying the spraying current (550 A for coating A and 650 A for coating B).

To characterize the coatings, the following techniques were utilized:

  • Scanning Electron Microscopy (SEM): Used to observe the surface morphology and cross-sectional structure of the coatings.
  • X-ray Diffraction (XRD): Employed to analyze the phase composition and crystal structure of the coatings.
  • Energy Dispersive X-ray Diffraction (EDX): Used to determine the elemental composition of the coatings.
  • Vickers Microhardness Testing: To measure the hardness of the coatings.
  • Adhesion Strength Testing: Performed according to ASTM C633 standard to assess the bond strength between the coating and the substrate.
  • Volume Resistivity Measurement: Conducted according to GB/T 1410-2006 to evaluate the electrical insulation properties.
  • Image Analysis Software (Image J): Utilized to quantify the porosity of the coatings from SEM images.

Datasets

Not discussed in the paper. The study focuses on the preparation and characterization of novel composite coatings rather than training or evaluating models on existing datasets.

Key Insights and Ideas

  • Synergistic Properties: The combination of Al₂O₃ (known for insulation and thermal stability) and h-BN (offering thermal conductivity, insulation, and wear resistance) creates a composite material with enhanced properties beyond those of individual components.
  • APS Parameter Influence: The study highlights that key APS parameters, particularly the spraying current, significantly influence coating properties like porosity, microhardness, and volume resistivity.
  • Negative Correlation between Porosity and Resistivity: A crucial finding is the inverse relationship between coating porosity and volume resistivity. Higher spraying currents lead to denser coatings with lower porosity, which in turn results in higher volume resistivity (better insulation).
  • Phase Transformation: The APS process induces a phase transformation in Al₂O₃ from the stable α-Al₂O₃ to the metastable γ-Al₂O₃ phase, which is influenced by the rapid cooling rates inherent in the spraying process.
  • Bonding Layer Effectiveness: The inclusion of a Ni₂0Cr bonding layer between the steel substrate and the Al₂O₃/h-BN coating is shown to effectively relieve internal stresses caused by thermal expansion mismatches, improving overall adhesion.

Key Results

  • Porosity: Coating A (550 A) had a porosity of 6.04%, while Coating B (650 A) exhibited a lower porosity of 4.75%.
  • Microhardness: Coating A had a microhardness of 781 ± 0.5 HV, whereas Coating B showed a higher microhardness of 840.5 ± 0.5 HV.
  • Adhesion Strength: Both coatings demonstrated excellent adhesion, with Coating A at 22.0 MPa and Coating B at 22.3 MPa.
  • Volume Resistivity: Coating A had a volume resistivity of 9.29 × 10¹⁰ Ω·cm, and Coating B had a resistivity of 3.55 × 10¹⁰ Ω·cm. Both values exceed the critical threshold of 1 × 10¹⁰ Ω·cm required for corona roller applications.
  • Coating B Superiority: The coating prepared with a higher spraying current (650 A, Coating B) consistently showed better performance in terms of lower porosity, higher microhardness, and good adhesion, indicating its superior mechanical and electrical properties.

Limitations and Future Work

  • Limitations:
  • The study primarily focuses on the preparation and characterization of the coatings under specific APS parameters. A more extensive parameter study could reveal further optimization possibilities.
  • While wear resistance and chemical stability are mentioned as desired properties, the paper focuses more on mechanical and electrical characteristics. Direct testing of wear and chemical resistance under operational conditions would be beneficial.
  • The study acknowledges the presence of micropores and small cracks, which are typical in APS coatings. Further research into minimizing these defects could lead to even better performance.
  • Future Work:
  • Investigating the long-term performance and durability of these Al₂O₃/h-BN coatings under actual corona roller operating conditions.
  • Exploring a wider range of APS parameters and composite compositions to further optimize properties.
  • Conducting detailed studies on the wear resistance and chemical stability of the coatings to fully assess their suitability for demanding applications.
  • Investigating the potential for these coatings in other high-voltage electrical applications beyond corona rollers.

Summary updated

Abstract

To improve the adhesion strength of polymer functional films, corona treatment is required. Corona rollers are key components for corona treatment, which are used in high-voltage electric fields for a long time. In this work, in order to improve electrical insulation, arc resistance, wear resistance, and chemical stability, a coating is usually sprayed on the surface of the corona roller. Al2O3/h-BN composite coatings are prepared on the surface substrate of a corona roller (20 steel) by atmospheric plasma spraying (APS) technology. Scanning Electron Microscope (SEM) and X-ray diffraction (XRD) analysis showed that the Al2O3/h-BN composite coating had a layered structure and compactness. Two kinds of Al2O3/h-BN composite coatings are prepared under different APS process parameters; the porosities of A coating and B coating are 6.04% and 4.75%, the microhardnesses are 781 ± 0.5 Hv and 840.5 ± 0.5 Hv, and the adhesion strengths are 22.0 MPa and 22.3 MPa, respectively. The A and B volume resistivity of the coatings are 9.29 × 1010 Ω·cm and 3.55 × 1010 Ω·cm, respectively. The volume resistivity and porosity of the coatings are negatively correlated, and they decrease with the increase in spraying current. But for both coatings, volume resistivity is greater than 1 × 1010 Ω cm. These results indicate that the Al2O3/h-BN composite coatings, as a new type of electrode roller coating, satisfy the use requirement. Al2O3/h-BN composite coatings can become the potential for ceramic coatings that have good mechanics and insulation performance.
BibTeX
@inproceedings{guo2024preparation,
  author = {Yifeng Guo and Lingxiao Lan and Boying Qin and Xinghua Liang and Yujiang Wang and Yu Wang and Zhikun Chen},
  title = {{Preparation and Characterization of Al2O3/h-BN Composite Coatings by Atmospheric Plasma Spraying (APS)}},
  booktitle = {Crystals},
  year = {2024},
  doi = {10.3390/cryst14121035},
}
Figure