Preparation and Application of Fluorescent Carbon Dots

Yaru Yang, Feng Lu, Min Hu, Youshen Wu, Dan Xiang, Peihong Gao, Wen ZhangUniversity 2020 · DOI

TL;DR

This paper details a practical undergraduate chemistry experiment focused on synthesizing and characterizing fluorescent carbon dots (CDs). The experiment guides students through the "bottom-up" synthesis of blue and green CDs, exploring their photoluminescence properties, and applying them to create fluorescent ink for anti-counterfeiting applications.

What Problem Does This Paper Address?

Traditional inorganic chemistry lab experiments often rely on outdated verification and preparation methods, failing to keep pace with rapid technological advancements. This paper addresses this gap by proposing a modern, engaging experiment that incorporates cutting-edge fluorescent nanomaterials – carbon dots. The goal is to enhance students' understanding of fundamental photoluminescence principles, develop their practical lab skills, and foster an appreciation for the application of advanced materials in real-world scenarios, such as anti-counterfeiting.

Methods

The core of the experiment involves a "bottom-up" synthesis approach for creating fluorescent carbon dots. Specifically:

  • Synthesis of Green Carbon Dots (GC-dots): This involves a solid-phase reaction of ammonium citrate and urea at 200°C for 1 hour, followed by dissolution in deionized water and centrifugation.
  • Synthesis of Blue Carbon Dots (BC-dots): This method uses citric acid, polyethyleneimine, and deionized water heated at 200°C for 1 hour, also followed by dissolution, centrifugation, and lyophilization.

Following synthesis, students characterize the CDs using:

  • Fluorescence Spectroscopy: Measuring excitation and emission spectra to understand the relationship between absorbed and emitted light.
  • Fluorescence Quantum Yield Measurement: A relative method is employed, using Rhodamine 6G (R6G) as a reference fluorophore to determine the efficiency of light emission.
  • Investigation of Influencing Factors: Students explore how concentration and pH affect the fluorescence intensity of the carbon dots.
  • Application in Fluorescent Ink: The synthesized CDs are incorporated into a PVA solution to create fluorescent inks for anti-counterfeiting purposes.
  • Data Analysis: The Origin software is used for plotting and analyzing experimental data.

Datasets

Not discussed in the paper. The paper describes experimental procedures and results obtained from laboratory measurements, not from pre-existing datasets.

Key Insights and Ideas

  • "Bottom-up" synthesis is accessible for undergraduate labs: The paper demonstrates that synthesizing fluorescent carbon dots with tunable colors (blue and green) can be achieved using relatively simple starting materials and standard laboratory heating equipment, making it suitable for an undergraduate curriculum.
  • Tunable fluorescence properties: The experiment highlights that different precursors and synthesis conditions can lead to carbon dots with distinct emission wavelengths, showcasing the potential for color tuning.
  • Stokes shift is a fundamental property: Students directly observe and quantify the Stokes shift (the difference between excitation and emission maxima), a key concept in understanding photoluminescence.
  • Environmental factors influence fluorescence: The experiment reveals that pH and solvent composition can significantly impact the fluorescence intensity of carbon dots, providing practical insights into their behavior.
  • Practical application in anti-counterfeiting: The successful creation of fluorescent ink demonstrates a tangible application of carbon dots, bridging theoretical knowledge with practical utility.

Key Results

  • Synthesis of Blue and Green CDs: The experiment successfully produced blue and green fluorescent carbon dot solutions.
  • Stokes Shift: GC-dots exhibited a Stokes shift of 103 nm, while BC-dots showed a shift of 84 nm.
  • Fluorescence Quantum Yield: The measured quantum yields for GC-dots and BC-dots were approximately 0.51 and 0.50, respectively. These values are comparable to literature reports, though the paper notes a discrepancy with one cited value for GC-dots (0.13).
  • Concentration Dependence: Fluorescence intensity showed a good linear correlation with concentration (R² > 0.99) within a certain range.
  • pH Dependence: GC-dots showed increased fluorescence intensity in alkaline conditions, while BC-dots were more fluorescent in neutral to slightly acidic conditions.
  • Solvent Dependence: GC-dots' fluorescence intensity generally increased with increasing ethanol concentration, whereas BC-dots' intensity decreased in ethanol.
  • Fluorescent Ink Efficacy: The synthesized fluorescent inks were successfully applied to various materials (paper, wood, plastic, glass) and showed distinct fluorescence under UV light, confirming their anti-counterfeiting potential.

Limitations and Future Work

  • Standardization of Relative Quantum Yield: The paper acknowledges that the choice of standard, its purity, and concentration significantly influence the accuracy of relative fluorescence quantum yield measurements.
  • BC-dot Structure and Solvent Interaction: The paper suggests that the observed decrease in BC-dot fluorescence in ethanol might be due to the disruption of its molecular structure by ethanol's hydroxyl groups or changes in solution polarity. Further investigation into these mechanisms is implied.
  • Broader Applications: While the paper focuses on anti-counterfeiting, the excellent fluorescence properties of carbon dots suggest potential for broader applications in areas like bioimaging, sensing, and optoelectronics, which could be explored in future work.
  • Curriculum Integration: The paper proposes integrating this experiment into a comprehensive 8-hour lab session for second-year chemistry students, including synthesis, characterization, data analysis, and application.

Summary updated

Abstract

The paper designed a chemical experiment based on carbon dots which own excellent fluorescence properties.Students need to synthesize blue and green carbon dots through "bottom-up" method, search the relationship between fluorescence excitation spectra and fluorescence emission spectra, measure the fluorescence quantum yield by comparing with a reference fluorophore, explore the changes of fluorescence spectra at different concentrations and pH, and apply the carbon dots to anti-counterfeit materials.All these will make students have a good command of fluorescence principle, such as fluorescence excitation spectrum, fluorescence emission spectrum, fluorescence quantum yield, Stokes shift and the factors that influence fluorescence.We also encourage students to apply the knowledge they have learned to their daily life.
BibTeX
@inproceedings{yang2020preparation,
  author = {Yaru Yang and Feng Lu and Min Hu and Youshen Wu and Dan Xiang and Peihong Gao and Wen Zhang},
  title = {{Preparation and Application of Fluorescent Carbon Dots}},
  booktitle = {University},
  year = {2020},
  doi = {10.3866/pku.dxhx202009038},
}

Loading related content...

Figure