Predicting The Axial Load Of Capacity Of Joints Formed By V-Band Retainers

Matthias A. Müller, Liam BluntUniversity 2009

Abstract

V-band retainers are widely used in the automotive, aircraft, and aerospace industries to connect a pair of circular flanges, providing joints with high axial strength and torsional rigidity. These components are typically manufactured using a cold rolling process. Despite their ubiquity, the complex interaction between the flange and the band upon assembly remains under-researched. Furthermore, the specific failure modes of V-band clamps under axial loading are not fully understood, particularly regarding the influence of the manufacturing process on final performance.

Introduction

V-band retainers are essential for securing circular flanges in high-performance environments, such as jet engines and turbochargers. A significant gap in current engineering knowledge is the impact of the manufacturing process—specifically cold rolling—on the structural integrity of the final joint. Cold rolling induces work hardening, which alters the material's physical properties, making it harder and less ductile. Most traditional models treat the clamp as a finished product with uniform properties, neglecting the residual stresses and plastic deformations inherent to the manufacturing cycle. This research aims to bridge this gap by developing a predictive model that accounts for the entire lifecycle of the part.

Methodology

The study utilized a multi-tiered Finite Element Analysis (FEA) approach to simulate both the manufacturing and operational phases of V-band retainers. The team employed 2D FEA to track plastic strain across six distinct rolling passes, followed by axisymmetric 2D models to simulate the joint under axial load.

To capture more complex physical phenomena, a 3D FE model was developed. This advanced simulation allows for the prediction of springback (the metal's tendency to return to its original shape after deformation), buckling, and longitudinal strain, which are critical for ensuring the quality of the final product.

Figure 1: 3D Finite Element model of the seven-pass cold rolling process and the corresponding stage schematic.

Key Insights and Results

The research demonstrated that manufacturing history is a critical variable in predicting part failure. The numerical plastic strain values derived from simulations showed a high correlation with physical work hardening measurements, validating the FEA approach.

The Diameter Factor

A key finding was the significant impact of the V-band's diameter on its mechanical behavior. Larger diameter bands tend to exhibit more elastic deformation, which fundamentally changes load distribution across the joint compared to smaller diameter variants. This geometric sensitivity highlights why 2D "slice" models are often insufficient for complex aerospace components.

Figure 2: Comparison of Equivalent Plastic Strain (PEEQ) for small (55mm) and large (1500mm) diameter V-bands, illustrating the difference in strain distribution.

Predictive Accuracy

The axisymmetric models for axial load capacity aligned well with experimental results. This provides engineers with a reliable method to estimate joint strength without the need for exhaustive physical testing. Additionally, the 3D analysis successfully identified the influence of roller distance and forming length on product quality, offering a pathway to optimize manufacturing and prevent defects like buckling.

Conclusion and Future Work

While the current models provide a robust framework, certain limitations remain. The influence of the T-bolt fastener, which introduces asymmetrical stresses, is not yet captured in axisymmetric models. Furthermore, the role of surface roughness in contact pressure requires deeper investigation. Future research will focus on integrating 3D manufacturing outputs directly into assembly simulations to create a seamless digital thread for predicting ultimate axial load capacity.

Summary updated

Abstract

V-band retainers are widely used in the automotive, aircraft and
\naerospace industries to connect a pair of circular flanges to provide a joint
\nwith good axial strength and torsional rigidity. V-band retainers are
\nmanufactured using a cold rolling process. Despite their wide application,
\nonce assembled to a pair of flanges little is known about the interaction
\nbetween flange and band. Moreover the failure mode of V-band clamps
\nwhen applying an axial load is not fully understood.
BibTeX
@inproceedings{muller2009predicting,
  author = {Matthias A. Müller and Liam Blunt},
  title = {{Predicting The Axial Load Of Capacity Of Joints Formed By V-Band Retainers}},
  booktitle = {University},
  year = {2009},
}
Figure