ppb-Level Selective Hydrogen Gas Detection of Pd-Functionalized In2O3-Loaded ZnO Nanofiber Gas Sensors

Jae-Hyoung Lee, Jae-Hun Kim, Jin-Young Kim, Ali Mirzaei, Hyoun Woo Kim, Sang Sub Kim2019 · DOI

TL;DR

Researchers have developed a highly sensitive and selective hydrogen gas sensor using Pd-functionalized In₂O₃-loaded ZnO nanofibers. This novel sensor can detect hydrogen at ppb levels, offering a significant advancement for safety and industrial applications where early hydrogen leak detection is critical.

What Problem Does This Paper Address?

Hydrogen gas is a promising clean energy source, but its high flammability and lack of odor, color, or taste make it a significant safety hazard. Early and reliable detection of hydrogen leaks is crucial for preventing accidents in storage, transport, and industrial use. While ZnO-based gas sensors are known for their potential in hydrogen detection due to their favorable properties, enhancing their sensitivity, selectivity, and response speed remains a challenge. Existing methods often involve complex fabrication processes or lack the required performance for real-world applications. This paper aims to address these limitations by developing a simple yet highly effective hydrogen gas sensor through strategic functionalization and material composition.

Methods

The researchers employed a multi-step fabrication process:

  • Electrospinning: This technique was used to create the core ZnO nanofibers. A viscous solution containing polyvinyl alcohol (PVA), zinc chloride dihydrate (ZnCl₂·2H₂O), and indium nitrate hydrate (In(NO₃)₃·4.5H₂O) was prepared. The ratio of In(NO₃)₃·4.5H₂O was varied (0.05, 0.1, and 0.15 molar ratio) to control the In₂O₃ loading. The solution was then electrospun into nanofibers, followed by annealing at 600 °C to remove organic matter and form crystalline phases.
  • Pd Nanoparticle Functionalization: Palladium (Pd) nanoparticles were deposited onto the surface of the In₂O₃-loaded ZnO nanofibers using a UV reduction method. This involved immersing the nanofibers in a Pd²⁺-containing solution and irradiating it with UV light. The functionalized nanofibers were then annealed at 500 °C.
  • Gas Sensing Measurements: The fabricated sensor devices were tested in a tube furnace with controlled gas atmospheres. Resistance changes were measured using a Keithley source meter. The sensor response was calculated as the ratio of resistance in air to resistance in the presence of the target gas (for reducing gases like H₂ and CO). Response and recovery times were defined as the time to reach 90% of the final resistance change.

Datasets

Not discussed in the paper. The study focuses on the fabrication and characterization of a novel sensor material and its performance evaluation under controlled gas exposure.

Key Insights and Ideas

  • Synergistic Effect of In₂O₃ and Pd: The combination of In₂O₃ loading and Pd functionalization on ZnO nanofibers proved crucial for enhancing hydrogen sensing performance. In₂O₃ acts as a co-catalyst, and Pd significantly boosts sensitivity and selectivity.
  • Optimal In₂O₃ Loading: The study identified 0.1 molar ratio of In₂O₃ as optimal for the ZnO nanofibers, leading to the strongest response to hydrogen gas.
  • Pd Nanoparticles as Catalysts: Pd nanoparticles play a vital role by efficiently dissociating hydrogen molecules and forming PdHx, which facilitates electron transfer and significantly increases the sensor's response.
  • Heterojunction Formation: The formation of Pd/ZnO Schottky junctions and In₂O₃/ZnO heterojunctions, along with ZnO-ZnO homojunctions, contributes to the enhanced sensing mechanism by modulating the electron depletion layer.
  • High Selectivity: The sensor demonstrated excellent selectivity towards hydrogen gas, showing significantly lower responses to CO and NO₂. This is attributed to the smaller kinetic diameter of H₂ allowing for deeper diffusion into the sensing layer.
  • Long-Term Stability: The optimized sensor exhibited remarkable stability over a 12-month period, indicating its potential for practical, long-term applications.

Key Results

  • The Pd-functionalized 0.1 In₂O₃-loaded ZnO nanofibers sensor showed a very strong response to 50 ppb hydrogen gas at 350 °C, with a response of 172.
  • The optimal sensing temperature was determined to be 350 °C.
  • At 350 °C, the sensor exhibited responses of 72, 88, 96, and 114 to 50 ppb, 100 ppb, 1 ppm, and 5 ppm H₂ gas, respectively.
  • For 50 ppb concentrations, the sensor showed responses of 152 for H₂, 14.6 for NO₂, and 13.48 for CO, demonstrating excellent selectivity.
  • The sensor maintained its high performance after 12 months, indicating excellent long-term stability.

Limitations and Future Work

  • Optimization of Pd Content: While the study optimized In₂O₃ loading, the authors suggest that further enhancement in gas response could be achieved by optimizing the content of Pd NPs.
  • Further Mechanistic Studies: While the paper proposes several mechanisms (heterojunctions, PdHx formation, metallization of ZnO), deeper investigations into the precise contributions of each factor could provide further insights.
  • Operating Temperature: The optimal operating temperature of 350 °C, while effective, might be a consideration for low-power applications. Future work could explore strategies to achieve high performance at lower temperatures.

Summary updated

BibTeX
@misc{lee2019ppb,
  author = {Jae-Hyoung Lee and Jae-Hun Kim and Jin-Young Kim and Ali Mirzaei and Hyoun Woo Kim and Sang Sub Kim},
  title = {{ppb-Level Selective Hydrogen Gas Detection of Pd-Functionalized In2O3-Loaded ZnO Nanofiber Gas Sensors}},
  year = {2019},
  doi = {10.3390/s19194276},
}
Figure