Polymer Distribution and Mechanism Conversion in Multiple Media of Phase-Separated Controlled-Release Film-Coating

Lu Chen, Guobao Yang, Xiaoyang Chu, Chun‐Hong Gao, Yuli Wang, Wei Gong, Zhiping Li, Meiyan Yang, Chunsheng GaoPharmaceutics 2019 · DOI

TL;DR

This study investigates how different release media (varying in pH, ionic strength, and osmolarity) affect the drug release rate from ethyl cellulose/hydroxypropyl cellulose (EC/HPC) coated pellets. The findings reveal that the media's influence on the coating's microstructure and polymer properties can override drug solubility, leading to complex release behaviors and highlighting the importance of media selection for optimizing controlled-release formulations.

What Problem Does This Paper Address?

Developing effective controlled-release drug delivery systems is crucial for optimizing therapeutic outcomes and patient compliance. Film coatings, particularly those made from blends of water-insoluble (like ethyl cellulose, EC) and water-soluble (like hydroxypropyl cellulose, HPC) polymers, are a common strategy for achieving this. HPC acts as a pore-former, creating channels for drug release as it leaches out. However, the in vitro release profiles of these systems can be highly sensitive to the surrounding environment, specifically the composition of the release medium. This study addresses the critical gap in understanding how variations in pH, ionic strength, and osmolarity of the release media influence the drug release kinetics and underlying mechanisms of EC/HPC coated pellets, which is essential for accurate prediction of in vivo performance and for rational formulation design.

Methods

The researchers employed a multi-faceted approach to investigate drug release:

  • Preparation of Coated Pellets: Metoprolol succinate (a model drug) was coated onto starter cores using fluidized bed coating with varying ratios of EC/HPC (from 100:0 to 74:26 w/w).
  • In Vitro Drug Release Studies: Pellets were tested in various media: deionized water, HCl solution (pH 1.2), acetate buffer (pH 4.5), and phosphate buffer (pH 6.8). The effects of ionic strength and osmolarity were further explored by adding NaCl.
  • HPC Leaching and Swelling: The rate at which HPC leached from the coating and the swelling behavior of the pellets were monitored to understand pore formation.
  • Free Film Analysis: EC/HPC free films were prepared to study their water uptake and microstructure using Scanning Electron Microscopy (SEM). This allowed for direct observation of how media affected film morphology.
  • Viscosity Measurements: The viscosity of HPC solutions in different media was measured to assess how media composition influenced the polymer's behavior.
  • Mathematical Modeling: A theoretical framework based on osmotic pumping and diffusion was applied to quantitatively explain the observed release mechanisms.

Datasets

Not discussed in the paper. The study utilized prepared drug-coated pellets and free films as experimental materials.

Key Insights and Ideas

  • Media Dominates Solubility: Surprisingly, drug release rates in different media did not always correlate with drug solubility. In some cases, faster release occurred even when drug solubility was lower, suggesting that media effects on the coating structure are paramount.
  • Acetate Buffer's Peculiar Effect: Acetate buffer at pH 4.5 consistently led to faster drug release, regardless of HPC levels, even when drug solubility was not exceptionally high. This points to a specific interaction between acetate and the EC/HPC film that enhances permeability.
  • HCl's HPC Dependence: In HCl solution (pH 1.2), drug release was strongly dependent on HPC levels. Higher HPC concentrations led to faster release, likely due to increased pore formation and reduced film integrity.
  • Phosphate Buffer's Osmolarity Sensitivity: Release in phosphate buffer was primarily influenced by osmolarity, not pH or HPC levels, suggesting a more straightforward osmotic mechanism.
  • EC/HPC Synergy: The study suggests that the combined action of EC and HPC, rather than HPC alone, dictates the final pore structure and permeability of the film, influencing release mechanisms.
  • Microstructure Mirrors Release: SEM observations of free films directly correlated with drug release profiles, showing how media can alter pore size and distribution, thereby affecting drug diffusion.

Key Results

  • Drug release was significantly faster in acetate buffer (pH 4.5) compared to other media, even with lower drug solubility.
  • In HCl solution (pH 1.2), increasing HPC content from 20% to 24% led to a substantial increase in drug release rate.
  • Phosphate buffer (pH 6.8) showed reduced drug release, primarily sensitive to osmolarity.
  • SEM analysis revealed that acetate buffer and HCl solution, particularly at higher concentrations, induced larger pores in the EC/HPC films compared to deionized water or phosphate buffer.
  • Mathematical modeling confirmed that release mechanisms shifted between osmotic pumping and diffusion depending on the media and HPC content, with diffusion becoming more dominant in HCl and acetate buffers.

Limitations and Future Work

  • Model Drug Specificity: The study used metoprolol succinate as a model drug. While it has good aqueous solubility, its specific properties might influence the observed interactions. Future work could explore other drugs with different solubility profiles.
  • In Vitro/In Vivo Correlation: While the study provides mechanistic insights, direct in vivo validation of these findings is not presented. Establishing robust in vitro-in vivo correlations (IVIVCs) for these formulations under various media conditions would be a valuable next step.
  • Complex Media: The study focused on relatively simple buffer systems. Investigating the effects of more complex physiological fluids (e.g., gastrointestinal fluids with enzymes and varying compositions) would provide a more comprehensive understanding.
  • Optimization Potential: The authors suggest that these findings can facilitate the optimization of film-coated formulations. Future work could focus on designing specific EC/HPC ratios and media conditions to achieve desired release profiles for different therapeutic applications.

Summary updated

Abstract

Phase-separated films of water-insoluble ethyl cellulose (EC) and water-soluble hydroxypropyl cellulose (HPC) can be utilized to tailor drug release from coated pellets. In the present study, the effects of HPC levels and the pH, type, ionic strength and osmolarity of the media on the release profiles of soluble metoprolol succinates from the EC/HPC-coated pellets were investigated, and the differences in drug-release kinetics in multiple media were further elucidated through the HPC leaching and swelling kinetics of the pellets, morphology (SEM) and water uptake of the free films and the interaction between the coating polymers and the media compositions. Interestingly, the drug release rate from the pellets in different media was not in agreement with the drug solubility which have a positive correlation with the drug dissolution rate based on Noyes⁻Whitney equation law. In particular, the drug release rate in acetate buffer at pH 4.5 was faster than that in other media despite the solubility of drug was relatively lower, regardless of the HPC levels. It may be attributed to the mutual effect between the EC and acetate buffer, which improved the permeability of the film. In contrast, the release of drug in HCl solution was dependent on the HPC levels. Increasing the levels of HPC increased the effects of hydrogen ions on the polymer of HPC, which resulted in a lower viscosity and strength of the gel, forming the larger size of pores in polymer films, thus increasing the drug diffused from the coating film. Further findings in phosphate buffer showed a reduction in the drug release compared to that in other media, which was only sensitive to the osmolarity rather than the HPC level and pH of the buffer. Additionally, a mathematical theory was used to better explain and understand the experimentally measured different drug release patterns. In summary, the study revealed that the effects of the media overcompensated that of the drug solubility to some extent for controlled-release of the coating polymers, and the drug release mechanism in multiple media depend on EC and HPC rather than on HPC alone, which may have a potential to facilitate the optimization of ideally film-coated formulations.
BibTeX
@inproceedings{chen2019polymer,
  author = {Lu Chen and Guobao Yang and Xiaoyang Chu and Chun‐Hong Gao and Yuli Wang and Wei Gong and Zhiping Li and Yang Yang and Meiyan Yang and Chunsheng Gao and Chunsheng Gao and Chunsheng Gao},
  title = {{Polymer Distribution and Mechanism Conversion in Multiple Media of Phase-Separated Controlled-Release Film-Coating}},
  booktitle = {Pharmaceutics},
  year = {2019},
  doi = {10.3390/pharmaceutics11020080},
}
Figure