Polycarbonate mPOF-Based Mach-Zehnder Interferometer for Temperature and Strain Measurement

Xiaoyu Yue, Haijin Chen, Hang Qu, Rui Min, Getinet Woyessa, Ole Bang, Xuehao Hu2020 · DOI

TL;DR

Researchers have developed a novel, low-cost Mach-Zehnder interferometer using microstructured polymer optical fiber (mPOF) for simultaneous temperature and strain sensing. This approach overcomes challenges in connecting polymer and silica fibers, offering high sensitivity and a straightforward fabrication process.

What Problem Does This Paper Address?

Traditional fiber optic sensors often rely on silica optical fibers (SOFs). While effective, SOFs can be brittle and expensive. Polymer optical fibers (POFs) offer advantages like flexibility, lower cost, and higher sensitivity to certain stimuli, making them attractive for sensing applications. However, a significant hurdle in utilizing POFs, particularly microstructured POFs (mPOFs), in existing fiber optic systems is the difficulty in reliably connecting them to standard SOF infrastructure. This is due to differences in melting points and the lack of commercial splicing equipment for POF-SOF connections. This paper addresses this by developing a practical method for connectorizing mPOFs with SOFs and then integrating this into a Mach-Zehnder (M-Z) interferometer for robust temperature and strain measurements.

Methods

The core of this work involves two key methodological innovations:

  • POF-SOF Connectorization: The authors devised an "imaging projecting method" to align single-mode mPOFs with SOFs. This technique uses a red-light universal fault locator, an objective lens, and a white paper screen to visualize the fiber ends. By observing the projected image, they can precisely align the cores of the two fibers. The connection is then permanently cured using UV glue. This method is crucial because standard fusion splicing is not feasible for POF-SOF connections due to their differing material properties.
  • Mach-Zehnder Interferometer (M-Z) Configuration: A standard M-Z interferometer setup was adapted. A He-Ne laser beam is split into two arms: a reference arm (SOF) and a sensing arm. The sensing arm incorporates a section of the polycarbonate (PC) mPOF. Changes in temperature or strain applied to the mPOF alter its effective refractive index or length, leading to a phase shift in the light propagating through it. This phase shift manifests as a shift in the interference fringes observed at the output, which are then monitored by a camera.

Datasets

Not discussed in the paper.

Key Insights and Ideas

  • Bridging the Gap: The developed imaging projection method for POF-SOF connectorization is a significant practical advancement, enabling the integration of sensitive polymer fibers into existing fiber optic systems without specialized, expensive equipment.
  • Material Advantage: Polycarbonate mPOF exhibits a high thermo-optic coefficient (TOC) and a suitable glass transition temperature, making it a promising material for high-performance sensing.
  • Annealing for Stability: Annealing the PC mPOF at 125 °C for 36 hours significantly improved the linearity and reduced hysteresis in temperature measurements, suggesting that residual stress from the fiber fabrication process can impact sensor performance.
  • High Sensitivity: The PC mPOF-based M-Z interferometer demonstrates high sensitivity for both temperature and strain, outperforming some existing polymer and even silica-based sensors.
  • Cost-Effectiveness: The overall approach emphasizes low cost and ease of fabrication, making it accessible for a wider range of applications.

Key Results

  • Temperature Sensing (Non-annealed):
    • Sensitivity: 25.5 fringes/°C (increasing temp), 20.6 fringes/°C (decreasing temp).
  • Converted sensitivity per unit length: 135.6 fringes/°C/m.
  • Optical phase change: 852.2 rad/°C/m.
  • Temperature Sensing (Annealed, immediately after):
    • Sensitivity: 16.8 fringes/°C (increasing temp), 21.3 fringes/°C (decreasing temp).
  • Temperature Sensing (Annealed, 1 month later):
    • Improved linear response with sensitivity of ~20.7 fringes/°C (both directions).
  • Strain Sensing (Non-annealed):
    • Sensitivity: ~1463 fringes/%ɛ.
  • Linear response observed up to 2.06% strain.
  • Axial Force Sensitivity: ~2886 fringes/N.
  • Force Measurement Resolution: ~3.47 × 10⁻⁴ N.

Limitations and Future Work

  • Temperature Range: While the annealing temperature was 125 °C, the reported temperature measurements were conducted in a limited range (28-32 °C) for ease of data acquisition. The authors state that measurements for higher temperatures will be implemented in the future.
  • Hysteresis: Although annealing improved linearity, some hysteresis was still observed, particularly immediately after annealing. This suggests that further optimization of annealing protocols or fiber pre-treatment might be beneficial.
  • Higher Order Modes: The use of a 632.8 nm laser with a multimode SOF in the reference arm can lead to speckle patterns in the interference fringes. The authors note that using a longer wavelength where both fibers are single-mode could mitigate this.
  • Strain Range Extension: The current strain measurement was limited to 2.06%, while the fiber's pseudo-yield point is around 5%. Future work could explore extending the strain measurement range.
  • Environmental Factors: While temperature and RH were controlled during experiments, the long-term stability and performance in more complex, uncontrolled environments would be valuable to investigate.

Summary updated

BibTeX
@misc{yue2020polycarbonate,
  author = {Xiaoyu Yue and Haijin Chen and Hang Qu and Rui Min and Getinet Woyessa and Ole Bang and Xuehao Hu},
  title = {{Polycarbonate mPOF-Based Mach-Zehnder Interferometer for Temperature and Strain Measurement}},
  year = {2020},
  doi = {10.3390/s20226643},
}

Loading related content...

Figure