Poly (Vinylidene Fluoride-Hexafluoropropylene)–Lithium Titanium Aluminum Phosphate-Based Gel Polymer Electrolytes Synthesized by Immersion Precipitation for High-Performance Lithium Metal Batteries

Xuanan Lu, Jianguo Luo, Lingxiao Lan, Bing Zhang, Zhikun Chen, Yujiang Wang, Xinghua Liang, Qinglie MoGels 2024 · DOI

TL;DR

This paper presents a novel, cost-effective method for synthesizing flexible gel polymer electrolytes (GPEs) for high-performance lithium metal batteries. By incorporating lithium titanium aluminum phosphate (LATP) into a PVDF-HFP matrix using immersion precipitation, the researchers achieved significantly improved ionic conductivity and cycling stability, addressing key limitations of current GPE technology.

What Problem Does This Paper Address?

Lithium metal batteries (LMBs) hold immense promise for next-generation energy storage due to their high theoretical capacity. However, conventional liquid electrolytes pose safety risks like leakage. Solid-state electrolytes offer improved safety but often suffer from low ionic conductivity and high interfacial impedance. Gel polymer electrolytes (GPEs) aim to bridge this gap, combining the advantages of both liquid and solid electrolytes. Despite their potential, existing GPEs struggle with poor lithium ion transfer numbers, limited cycling stability, and low ionic conductivity, especially at room temperature. This hinders their widespread adoption in high-performance LMBs.

Methods

The researchers employed an immersion precipitation method to synthesize the PVDF-HFP-LATP gel polymer electrolytes. This involved:

  • Solution Preparation: Mixing PVDF-HFP and LATP powder in N,N-dimethylformamide (DMF).
  • Casting and Precipitation: Pouring the solution onto a PTFE sheet, spreading it, and then immersing it in deionized water. This process induces phase separation, forming a porous structure.
  • Desolvation and Drying: Removing residual DMF and drying the porous membrane.
  • Electrolyte Impregnation: Soaking the dried membrane in an organic liquid electrolyte (1 mol/L LiPF6 in EC:DMC:EMC).

The study systematically varied the LATP content to optimize the GPE's properties. Key characterization techniques included:

  • X-ray Diffraction (XRD): To analyze the crystalline phases of the materials.
  • Fourier Transform Infrared Spectroscopy (FTIR): To identify functional groups and confirm chemical interactions.
  • Scanning Electron Microscopy (SEM): To visualize the morphology and pore structure of the GPE.
  • Thermogravimetric Analysis (TGA): To assess thermal stability.
  • Electrochemical Impedance Spectroscopy (EIS): To measure ionic conductivity.
  • Linear Scanning Voltammetry (LSV): To determine the electrochemical window.
  • Galvanostatic Cycling: To evaluate lithium plating/stripping stability and battery performance.

Datasets

Not discussed in the paper. The study focuses on material synthesis and electrochemical testing of fabricated cells.

Key Insights and Ideas

  • Honeycomb Morphology is Key: The immersion precipitation method successfully created a porous, honeycomb-like structure in the GPE. This morphology is crucial for effectively storing the liquid electrolyte, leading to enhanced ionic conductivity.
  • LATP as a Performance Enhancer: Incorporating LATP not only increases the amorphous domain of the PVDF-HFP matrix, facilitating lithium ion transport, but also provides additional diffusion pathways. This significantly boosts ionic conductivity and the lithium ion transfer number.
  • Optimal LATP Concentration: The study found that a 10 wt% LATP concentration (GPE-10) yielded the best results. Higher LATP concentrations (e.g., 20 wt%) started to hinder ion movement, reducing conductivity.
  • Improved Mechanical and Thermal Stability: The addition of LATP enhanced the mechanical strength of the GPE and improved its dimensional stability at elevated temperatures, contributing to safer battery operation.
  • Simplified Synthesis: The immersion precipitation method is presented as a straightforward and scalable approach, making it attractive for industrial applications.

Key Results

  • Ionic Conductivity: The optimized GPE-10 achieved a high ionic conductivity of 1.03 × 10⁻³ S cm⁻¹ at room temperature (25 °C).
  • Lithium Ion Transfer Number: The tLi+ for GPE-10 was 0.58, significantly higher than that of GPE-0 (0.47), indicating improved lithium ion mobility.
  • Electrochemical Window: GPE-10 exhibited a wider electrochemical window of 4.6 V, compared to 4.3 V for GPE-0, offering better stability.
  • Liquid Electrolyte Uptake: GPE-10 showed excellent liquid electrolyte uptake of 168.6%.
  • Battery Performance (LiFePO4/GPE/Li):
    • Initial discharge capacity at 1C: 121.5 mAh/g.
  • Capacity retention after 300 cycles: 94.0%.
  • Demonstrated good rate performance across various current densities.
  • Cycling Stability: Li|GPE-10|Li symmetric cells showed stable cycling for 750 hours without significant polarization fluctuations, whereas Li|GPE-0|Li cells short-circuited after 115 hours.

Limitations and Future Work

  • Thermal Decomposition Temperature: While the GPE-10 showed good thermal stability, its decomposition temperature (around 390 °C) was slightly lower than GPE-0. However, the authors note it is still higher than typical liquid electrolytes and sufficient for operating at higher temperatures.
  • Further Optimization: The paper suggests that the cost-effective, efficient, and simple synthesis strategy holds immense promise for integration into next-generation lithium batteries, implying potential for further refinement and application.
  • Interfacial Stability: While improved, further investigation into the long-term interfacial stability between the GPE and electrodes, especially under demanding conditions, could be beneficial.

Summary updated

Abstract

Gel polymer electrolytes (GPEs) have high safety and excellent electrochemical performance, so applying GPEs in lithium batteries has received much attention. However, their poor lithium ion transfer number, cycling stability, and low room temperature ionic conductivity seriously affect the utilization of gel polymer electrolytes. This paper successfully synthesized flexible poly (vinylidene fluoride-hexafluoropropylene)-lithium titanium aluminum phosphate (PVDF-HFP-LATP) gel polymer electrolytes using the immersion precipitation method. The resulting GPE has a porous honeycomb structure, which ensures that the GPE has sufficient space to store the liquid electrolyte. The GPE has a high ionic conductivity of 1.03 ×10<sup>-3</sup> S cm<sup>-1</sup> at room temperature (25 °C). The GPE was applied to LiFePO<sub>4</sub>/GPE/Li batteries with good rate performance at room temperature. The discharge specific capacity of 1C was as high as 121.5 mAh/g, and the capacity retention rate was 94.0% after 300 cycles. These results indicate that PVDF-HFP-LATP-based GPEs have the advantage of simplifying the production process and can improve the utility of gel polymer lithium metal batteries.
BibTeX
@inproceedings{lu2024poly,
  author = {Xuanan Lu and Jianguo Luo and Lingxiao Lan and Bing Zhang and Zhikun Chen and Yujiang Wang and Xinghua Liang and Qinglie Mo},
  title = {{Poly (Vinylidene Fluoride-Hexafluoropropylene)–Lithium Titanium Aluminum Phosphate-Based Gel Polymer Electrolytes Synthesized by Immersion Precipitation for High-Performance Lithium Metal Batteries}},
  booktitle = {Gels},
  year = {2024},
  doi = {10.3390/gels10030179},
}
Figure