Photodetector Using the Pyromagnetic Effect of a Semiconductor Film

Kyoshiro Seki, Takashi Shibuya, S. Chiba, Hiroshi Osada, K. MurakamiJOURNAL 1994 · DOI

Abstract

The Magnetic Semiconductor Photodetector (MSP) is a 40-μm-thick transducer with a magnetic semiconductor film that is composed of MnO, ZnO and Fe2O3 and that has a surface painted with a radiant flux absorbent. Incident light increases the MSP temperature, increasing the MSP's magnetic reluctance. The magnetic density variation in the MSP is read out by a Hall element. MSP patterns can be printed on the substrate in various shapes (such as a plate, a ring, or a rod), and the MSP is suitable for use as a photosensor, a photochopper, a photorelay, or an exposure meter. Preparation techniques, pyromagnetic characteristics, and the light signal read out are discussed here.

Introduction

Conventional light sensors typically rely on electronic phenomena like photoconductivity or the photovoltaic effect. While effective, these sensors often require rigid architectures and direct electrical contacts, limiting their versatility in custom geometries or harsh environments. Researchers have developed a novel Magnetic Semiconductor Photodetector (MSP) that bypasses these limitations by utilizing a "pyromagnetic" chain reaction. By converting incident light into heat, which then alters the magnetic properties of a thick film, the MSP allows for non-contact signal transmission via a Hall element. This screen-printable sensor offers a flexible and robust alternative for applications requiring custom shapes or isolated signal paths.

Methods and Fabrication

The MSP's core is a 40-μm-thick film of manganese-zinc ferrite ($Mn_{0.6}Zn_{0.4}Fe_2O_4$). The fabrication process is designed for scalability and geometric flexibility.

Fabrication process of the Magnetic Semiconductor Photodetector (MSP).

The process begins with the synthesis of the magnetic material by mixing $MnO$, $ZnO$, and $Fe_2O_3$, followed by calcination at 850°C. The resulting material is ground into a fine powder (3–5 μm). This powder is then mixed with an inorganic binder to create a printable paste. Using screen-printing techniques, the paste is applied to an alumina substrate in desired patterns—such as rings, rods, or plates—and sintered at 1200°C. Finally, the film is sensitized with a radiant flux absorbent (carbon black or platinum black) to maximize light-to-heat conversion.

To detect signals, the MSP is integrated into a magnetic circuit driven by an AC field. As light hits the film, its temperature rises, modulating the magnetic reluctance. This variation is read out by a Hall element positioned beneath the substrate, providing a non-contact electrical output proportional to the light intensity.

Key Insights and Results

The performance of the MSP is governed by the pyromagnetic properties of the ferrite film, particularly its behavior near the Curie temperature ($T_c$).

Magnetic reluctance as a function of temperature for different powder-to-binder ratios (X).

The Role of the Curie Point

The ferrite composition was engineered to have a $T_c$ of approximately 30°C. As shown in the experimental data, the magnetic reluctance ($ℛ$) increases sharply as the temperature approaches this threshold. Because magnetic properties are most sensitive to thermal changes near the transition point, the sensor achieves peak sensitivity at typical room temperatures. Above 30°C, the material becomes paramagnetic, and the sensitivity plateaus.

Composition and Sensitivity

The weight ratio ($X$) of magnetic powder to binder is a critical design parameter. Increasing the ratio from $X=1$ to $X=3$ significantly enhances the output voltage. For instance, at an illuminance of 8000 lx, the $X=3$ sample produced an output of 150 mV, roughly 7.5 times greater than the $X=1$ sample. This demonstrates that maximizing the density of magnetic particles within the thick film is essential for high-gain transduction.

Performance Characteristics

  • Linearity: The conversion voltage ($δV_0$) exhibits a highly linear relationship with light intensity across the tested range (up to 8000 lx).
  • Durability: By utilizing a 40-μm thick film instead of bulk materials (typically ~700 μm), the researchers eliminated the thermal stress fractures common in earlier pyromagnetic sensors while improving response speed.
  • Absorbent Efficiency: Both carbon black and platinum black proved to be effective absorbents, ensuring efficient conversion of radiant flux into thermal energy.

Limitations and Future Outlook

While the MSP offers unique advantages in flexibility and non-contact readout, it faces certain constraints. Because it relies on a thermal process, the device has an inherent thermal lag, making it less suitable for high-speed optical communications compared to pure semiconductor photodetectors. Additionally, since the signal is temperature-dependent, ambient fluctuations can introduce noise, necessitating future development of temperature compensation circuitry. Future research will also explore the sensor's spectral response in the infrared (IR) and ultraviolet (UV) ranges to expand its utility in industrial and scientific monitoring.

Summary updated

Abstract

The Magnetic Semiconductor Photodetector (MSP) is a 40-μm-thick transducer with a magnetic semiconductor film that is composed of MnO, ZnO and Fe2O3 and that has a surface painted with a radiant flux absorbent. Incident light increases the MSP temperature, increasing the MSP's magnetic reluctance. The magnetic density variation in the MSP is read out by a Hall element. MSP patterns can be printed on the substrate in various shapes (such as a plate, a ring, or a rod), and the MSP is suitable for use as a photosensor, a photochopper, a photorelay, or an exposure meter. Preparation techniques, pyromagnetic characteristics, and the light signal read out are discussed here.
BibTeX
@article{seki1994photodetector,
  author = {Kyoshiro Seki and Takashi Shibuya and S. Chiba and Hiroshi Osada and K. Murakami},
  title = {{Photodetector Using the Pyromagnetic Effect of a Semiconductor Film}},
  journal = {JOURNAL},
  year = {1994},
  doi = {10.2150/jieij1980.78.10\_555},
}
Figure