Oxidation of printed circuit board wastes in supercritical water

Yi‐Chi Chien, H. Paul Wang, Kuen‐Song Lin, Yun YangWater 2000 · DOI

TL;DR

This paper investigates the supercritical water oxidation (SCWO) of printed circuit board (PCB) wastes, focusing on the role of sodium cations in enhancing bromine removal. The study demonstrates that SCWO effectively oxidizes PCB waste, with NaOH significantly improving the process and facilitating bromine's transfer to the liquid phase, while X-ray spectroscopy confirms the formation of copper oxides and hydroxides in the solid residue.

What Problem Does This Paper Address?

Printed circuit board (PCB) waste presents a significant environmental challenge due to its high bromine content. Traditional disposal methods like incineration can lead to the formation of toxic by-products such as HBr, Br₂, and brominated dioxins. While solidification/landfill is currently practiced, its cost is rising. This paper addresses the need for more effective and environmentally sound methods for treating PCB waste, specifically by exploring the potential of supercritical water oxidation (SCWO) to break down these complex materials and manage their hazardous components, particularly bromine.

Methods

The researchers employed a supercritical water oxidation (SCWO) process using a high-pressure quartz-lined batch reactor. PCB wastes were treated at temperatures ranging from 593 K to 793 K and pressures of 240 atm. Hydrogen peroxide was used as an oxidant. To understand the fate of bromine and the composition of the solid residue, several analytical techniques were utilized:

  • ICP-MS (Inductively Coupled Plasma Mass Spectrometry): Used to measure the concentration of bromine in samples.
  • X-ray Diffraction (XRD) Spectroscopy: Employed to identify the crystalline phases present in the solid residue after SCWO.
  • X-ray Absorption Spectroscopy (XAS): This included both X-ray Absorption Near Edge Structure (XANES) and Extended X-ray Absorption Fine Structure (EXAFS) to probe the local atomic environment and bonding of copper species in the solid residue.

The study also investigated the effect of sodium hydroxide (NaOH) addition on the SCWO process, comparing results with and without its presence.

Datasets

Not discussed in the paper. The study utilizes printed circuit board waste as the material for treatment and analysis.

Key Insights and Ideas

  • SCWO as an effective treatment for PCB waste: The process efficiently oxidizes the organic resin component of PCBs, converting it to CO₂ and H₂O.
  • The crucial role of NaOH: Adding NaOH significantly enhances the oxidation of PCB waste and, importantly, facilitates the removal of bromine.
  • Bromine migration to the liquid phase: In the presence of NaOH, a substantial portion of the bromine (63.2%) is found in the liquid phase after SCWO, with Br₂ identified as the main gaseous bromine species. This suggests a mechanism for effectively sequestering bromine away from potentially harmful gaseous emissions.
  • Copper speciation in the residue: XRD analysis reveals that the solid residue primarily consists of copper oxides (Cu₂O, CuO) and copper hydroxide (Cu(OH)₂).
  • No direct Cu-Br bonding observed: Crucially, EXAFS and XRD analyses did not detect any direct Cu-Br species in the solid residue. This suggests that copper is not directly involved in abstracting bromine from the resin matrix, and the observed bromine removal is likely mediated by sodium cations.
  • Sodium's potential role in bromine abstraction: The paper speculates that sodium cations might play a role in abstracting bromine, possibly through the formation of intermediate species like NaBr, which then precipitates or dissolves in the aqueous phase.

Key Results

  • Resin conversion: At 793 K for 10 minutes, the resin conversion in SCWO of PCB waste reached 0.90. Temperature dependence showed a resin conversion of approximately 0.73 at 593 K in subcritical water and increased with temperature in supercritical conditions.
  • Carbon balance: The carbon balance in SCWO of PCB waste was greater than 96%.
  • Bromine distribution with NaOH: In the presence of NaOH at 693 K for 10 min, 63.2% of the bromine was found in the water phase, and 36.8% in the gaseous phase. Without NaOH, the distribution was 40.0% in the water phase and 60.0% in the gaseous phase.
  • Solid residue composition: XRD confirmed the presence of Cu₂O, CuO, and Cu(OH)₂ in the solid residue.
  • EXAFS analysis of copper: The Cu-O bond distance in the solid residue was determined to be 1.87 Å with a coordination number of 2.61.

Limitations and Future Work

  • Limited study of Cu-Br interaction: While the study strongly suggests copper is not directly involved in bromine abstraction, the exact mechanism of bromine removal by sodium cations could be further elucidated.
  • Trace phenols and PAHs: The paper notes that trace phenols and polycyclic aromatic hydrocarbons (PAHs) were found in the SCWO process, indicating that complete mineralization might require optimization of reaction conditions or further treatment steps.
  • Further investigation of NaBr behavior: The paper mentions that NaBr could redissolve in subcritical conditions, suggesting that the fate of NaBr in different phases and conditions warrants further investigation.
  • Optimization of SCWO for complete destruction: Future work could focus on optimizing SCWO parameters to achieve complete destruction of all organic components and minimize the formation of any undesirable by-products.

Summary updated

BibTeX
@inproceedings{chien2000oxidation,
  author = {Yi‐Chi Chien and H. Paul Wang and Kuen‐Song Lin and Yun Yang},
  title = {{Oxidation of printed circuit board wastes in supercritical water}},
  booktitle = {Water},
  year = {2000},
  doi = {10.1016/s0043-1354(00)00184-6},
}
Figure