Optofluidic Assembly of InGaAsP Microdisk Lasers on Si Photonic Circuits with Submicron Alignment Accuracy

Ming-Chun Tien, Kyoungsik Yu, Aaron T. Ohta, Steven L. Neale, Ming C. Wu2009 · DOI

TL;DR

Researchers have developed a novel optofluidic assembly technique to precisely place tiny InGaAsP microdisk lasers onto silicon photonic circuits. This method achieves sub-micron alignment accuracy, enabling efficient coupling of laser light into silicon waveguides, a crucial step for integrating on-chip lasers with existing silicon photonics technology.

What Problem Does This Paper Address?

Silicon photonics holds immense promise for integrating optical functionalities with the ubiquitous CMOS electronics. While passive silicon photonic circuits and modulators are readily fabricated using standard CMOS processes, a significant hurdle has been the lack of efficient, on-chip semiconductor lasers. Direct epitaxial growth of III-V lasers on silicon is challenging due to high temperatures incompatible with CMOS fabrication. Existing hybrid integration methods, like wafer bonding, often struggle with the planarity requirements of multi-layered CMOS wafers. This paper addresses the need for a low-temperature, high-precision method to integrate pre-fabricated III-V lasers onto fully processed CMOS wafers, specifically focusing on coupling these lasers to sub-micron silicon waveguides.

Methods

The core innovation is the use of lateral-field optoelectronic tweezers (LOET) for the optofluidic assembly. Here's how it works:

  1. Microdisk Laser Fabrication: InGaAsP microdisk lasers (6 µm diameter, 200 nm thick) are grown on an InP substrate using metalorganic chemical vapor deposition (MOCVD). They are then released and suspended in an ethanol solution. The thinness of the microdisks is critical for evanescent coupling to silicon waveguides.
  2. Silicon Photonic Circuit Fabrication: Silicon waveguides (850 nm wide, 100 nm thick) are fabricated on a silicon-on-insulator (SOI) wafer. A thin oxide cladding layer is grown on top to facilitate optical coupling.
  3. LOET Integration: A specialized LOET structure, consisting of amorphous silicon (a-Si) photoconductor electrodes and aluminum, is patterned around the silicon waveguides and pedestals.
  4. Optofluidic Assembly: The suspended microdisk lasers in ethanol are transported and precisely aligned to the silicon waveguides using LOET. This is achieved by projecting optical patterns onto the a-Si layer, which induces localized electric fields. An AC voltage (1-10 Vpp at 200 kHz) is applied to drive the dielectrophoresis.
  5. Fixation and Finalization: Once aligned, the voltage is increased (to 20 Vpp) to hold the disks during solvent evaporation. Finally, the a-Si layer is selectively etched away using xenon difluoride to avoid interfering with optical modes.

This method is novel in its use of LOET for precise, room-temperature assembly of III-V microdisk lasers onto silicon photonic circuits, overcoming the temperature and planarity challenges of previous integration techniques.

Datasets

Not discussed in the paper. The paper focuses on the fabrication and characterization of a specific device.

Key Insights and Ideas

  • Optofluidics as a Precision Assembly Tool: The paper demonstrates that optofluidic techniques, specifically LOET, can achieve the sub-micron alignment accuracy required for efficient coupling between micro-scale lasers and nano-scale silicon waveguides.
  • Room-Temperature Integration: The LOET assembly process operates at room temperature, making it compatible with post-CMOS fabrication, a significant advantage over high-temperature epitaxial growth methods.
  • Thin Microdisks for Evanescent Coupling: The deliberate design of thin (200 nm) InGaAsP microdisk lasers is crucial for enabling evanescent optical coupling to the underlying silicon waveguides, allowing for efficient light transfer.
  • Successful Laser-Waveguide Integration: The successful demonstration of light coupling from the assembled microdisk laser into the silicon waveguide, evidenced by laser output measurements, validates the effectiveness of the assembly technique.

Key Results

  • Sub-micron Alignment Accuracy: The optofluidic assembly process achieved sub-micron alignment accuracy between the InGaAsP microdisk lasers and the silicon waveguides.
  • Effective Threshold Pump Power: The assembled microdisk lasers exhibited an effective threshold peak pump power of 0.6 mW (pulsed) when coupled to the waveguide.
  • Maximum Output Power: A maximum laser output power of 90 µW was achieved with 8.8 mW of pump power.
  • External Quantum Efficiency: The external quantum efficiency of the laser coupled to the waveguide was 3.5%.
  • Single-Mode Operation: Single-mode lasing operation was observed at a peak wavelength of 1572.6 nm.
  • Linewidth: The measured linewidth was <23 pm, limited by the optical spectrum analyzer's resolution.
  • Whispering Gallery Mode: A second whispering gallery mode was observed with a 15-dB suppression at higher pump powers.

Limitations and Future Work

  • Pulsed Operation: The current measurements were performed under pulsed optical pumping. Future work could focus on achieving electrically pumped operation for practical device integration.
  • Coupling Efficiency: While successful, the coupling efficiency could potentially be further optimized through finer control of waveguide dimensions and microdisk placement.
  • Scalability: The paper demonstrates the principle for a single laser. Future research would involve scaling this process to integrate multiple lasers and complex photonic circuits.
  • Material Compatibility: While this work focuses on InGaAsP lasers, the optofluidic assembly technique could potentially be adapted for other III-V laser materials and different waveguide platforms.

Summary updated

Abstract

We demonstrate optofluidic assembly of pre-fabricated InGaAsP microdisk lasers (6 µm diameter, 200 nm thickness) on silicon photonic circuits with sub-micron alignment accuracy. The laser output is successfully coupled to the integrated silicon waveguide.
BibTeX
@misc{tien2009optofluidic,
  author = {Ming-Chun Tien and Kyoungsik Yu and Aaron T. Ohta and Steven L. Neale and Ming C. Wu},
  title = {{Optofluidic Assembly of InGaAsP Microdisk Lasers on Si Photonic Circuits with Submicron Alignment Accuracy}},
  year = {2009},
  doi = {10.1364/ofc.2009.omr7},
}
Figure