TL;DR
This paper presents an optimized overload buffer structure for passive semi-strapdown inertial navigation systems (SINS) used in guided projectiles. By redesigning the spherical cap buffer with improved materials and a spring-based separation mechanism, the system significantly enhances its ability to withstand extreme launch overloads and maintain stability during high-speed flight, crucial for accurate navigation.
What Problem Does This Paper Address?
Guided projectiles require precise navigation information, which is typically provided by inertial navigation systems (INS). However, traditional INS components, like gyroscopes, have limited measurement ranges and are susceptible to damage from the extreme accelerations experienced during projectile launch (high overload) and high-speed rotation. Passive semi-strapdown INS, which isolate the inertial measurement unit (IMU) from the projectile's rolling motion, offer a solution by providing a more stable environment. A key challenge for these systems is the "isolation rolling platform," which uses bearings that are highly vulnerable to damage from the immense impact forces during launch. Existing overload buffer designs, while mitigating direct impact, can lead to increased friction and instability due to the deformation and persistent contact of spherical caps. This paper addresses the need for a more robust and stable overload protection mechanism for these systems.
Methods
The researchers propose an optimized overload buffer structure based on a point-contact spherical cap design. The key innovations include:
- Material Optimization: Replacing the original materials of the upper and lower spherical caps with higher-strength, high-elasticity modulus metals (35CrMnSiA for the upper cap and 40Cr for the lower cap) to improve hardness and toughness, and reduce deformation.
- High Damping Buffer: Incorporating a high-damping magnesium-based alloy (AZ91D) in the lower spherical cap's column to absorb stress and further reduce deformation and pivoting friction.
- Spring-Based Separation: Introducing a compression spring between the isolation rolling platform shaft and the bearing. This spring ensures that after the initial impact, the upper and lower spherical caps are actively separated, eliminating pivoting friction torque during the subsequent flight phases.
- Finite Element Analysis (FEA): Using FEA to simulate the deformation of the spherical caps under overload conditions, comparing the optimized design against the original.
- Ground Semi-Physical Simulation Experiments: Conducting impact tests and high-speed rotation tests to validate the performance of both the original and optimized buffer structures under simulated launch and flight conditions.
Datasets
Not discussed in the paper. The paper relies on simulations and experimental setups rather than pre-existing datasets.
Key Insights and Ideas
- Material Choice is Critical: The selection of specific high-strength steels for the spherical caps, with tailored hardness and toughness, is crucial for managing impact forces without catastrophic failure.
- Active Separation is Key to Stability: The introduction of a spring to actively separate the spherical caps after impact is a significant improvement. It directly addresses the issue of persistent contact and the resulting pivoting friction torque, which degrades the stability of the isolation rolling platform.
- Combined Approach Yields Superior Results: The optimization is not a single tweak but a combination of material science, mechanical design (spring separation), and damping materials, demonstrating a holistic approach to solving the overload problem.
- FEA and Experimentation Synergy: The paper effectively uses FEA to predict performance and then validates these predictions through rigorous physical testing, reinforcing the reliability of the proposed design.
Key Results
- Reduced Deformation: The optimized buffer structure reduced the maximum deformation radius of the lower spherical cap by 40.8% compared to the original design after a 12,000 g impact.
- Withstands High Overload: The optimized buffer structure can withstand an overload impact of 12,690 g, effectively protecting the bearing and internal sensors.
- Improved Stability: In high-speed rotation tests (3600°/s), the optimized system's isolation rolling platform exhibited a 52% improvement in anti-high-speed rotation capability, with a significantly more stable angular rate output (max 67.26°/s vs. 140.3°/s for the original).
- Elimination of Pivoting Friction: The spring-based separation mechanism successfully eliminated the detrimental pivoting friction torque during the out-bore flight phase.
Limitations and Future Work
- Material Limitations: While improved, the paper notes that the damping performance of the magnesium alloy is not as good as pure magnesium or rubber, suggesting potential for further material research.
- Specific Projectile Focus: The analysis and experiments were based on a specific 122 mm extended-range guided projectile. While the principles are generalizable, further validation for different projectile types and sizes might be beneficial.
- Future Work: The authors suggest that this design provides a stable test environment for IMUs and improves system accuracy, laying the groundwork for its application in conventional ammunition guidance. Further research could explore integrating this buffer into actual guided ammunition systems and conducting field tests.
Summary updated